Search Results

This paper discusses simplified lumped parameter thermal modeling of power train components. In particular, it discusses the tradeoff between model complexity and the ability to correlate the predicted temperatures and flow rates with measured data. The benefits and problems associated with using a three lumped mass model are explained and the value of this simpler model is promoted. The process for correlation and optimization using modern software tools is explained. Examples of models for engines and transmissions are illustrated along with their predictive abilities over typical driving cycles.

The Advanced ECS is under development for the purpose of saving fuel, improving safety, and cabin comfort. In FY2006 study, basic components (i.e. MDC, OBNOGS, desiccant units, and CO2 removers) have been improved and their performances evaluated including resistance to environmental condition (i.e. vibration). In addition, the suitable system configuration for a 90-seats aircraft has been considered to evaluate the feasibility of the system. In this paper, we show the results of the evaluated performances based on prototype components, and the analytical study of a revised system configuration.

For designing new products or developing new specifications, the reliability performance of systems and components experienced by the customer provides invaluable information for the engineer. This information, not only provides for the visibility of reliability requirements, but also an awareness of potential degradation of the systems and components during its life cycle. In this paper, a method is presented for predicting vehicle system and component reliability from vehicle fleet repair data. This method combines sampling stratification, computer data analysis and statistical modeling techniques into a reliability analysis procedure to provide reliability prediction. Specifically, published vehicle fleet data was used to provide the basis for predicting the vehicle system and component reliability at any mileage level.

Although rollover crashes represent a small fraction (approximately 3%) of all motor vehicle crashes, they account for roughly one quarter of crash fatalities to occupants of cars, light trucks, and vans (NHTSA Traffic Safety Facts, 2004). Therefore, the National Highway Traffic Safety Administration (NHTSA) has identified rollover injuries as one of its safety priorities. Motor vehicle manufacturers are developing technologies to reduce the risk of injury associated with rollover collisions. This paper describes the development by General Motors Corporation (GM) of a suite of laboratory tests that can be used to develop sensors that can deploy occupant protection devices like roof rail side air bags and pretensioners in a rollover as well as a discussion of the challenges of conducting this suite of tests.

Nowadays, space crafts such as a space shuttle take the O2 gas for crew respiration from the earth. However, for long periods of stay in space and far missions such as to the moon, it is not possible to carry sufficient amounts of oxygen. Therefore, there is need to establish other methods of supplying the extra O2 required by the crew under such circumstances. The CO2 reduction system is one method to generate O2 in space.

This paper discusses the feasibility and issues associated with integrating a consumer off-the shelf product into a vehicle. For this evaluation, we selected a handheld personal computer (HPC), cellular telephone and modem to integrate with the vehicle audio, climate and system controls. Connectivity between the HPC and the vehicle is established by the use of the standard infrared serial data link that comes with the HPC. Connectivity outside the vehicle uses a cellular telephone for voice and a cellular digital packet data (CDPD) modem for data. This system is built into the Dodge ESX-2 hybrid powered concept vehicle for demonstration.

The rapid growth of information technology has the potential to affect many of the reasons why people drive. The Internet is arguably the most significant recent milestone in the growth of information technology. This paper examines the ways Internet communication might affect the travel experience by a) eliminating traditional reasons for personal travel, b) providing new reasons, c) changing the balance between personal and freight travel, and d) changing trip length distribution. Changes of the types listed could affect the product demand "mix" for electric, hybrid-electric and fuel cell vehicles being developed.

The free-rolling cornering, straight-line braking, and pull force properties of a small sample of tire specifications is examined. This is done to examine potential differences between the specifications and the statistics of force and moment measurements. Two steer axle specifications, two drive axle specifications, and a trailer specification are considered, In addition, the evolution of properties for one drive axle specification is followed from new to naturally worn-out to retreaded. The summarized data is available from SAE Cooperative Research on electronic media.

The Auto/Steel Partnership established the Light Truck Frame Project Group in 1996 with two objectives: (a) to develop materials, design and fabrication knowledge that would enable the frames on North American OEM (original equipment manufacturer) light trucks to be reduced in weight, and (b) to improve corrosion resistance of frames on these vehicles, thereby allowing a reduction in the thickness of the components and a reduction in frame weight. To address the issues relating to corrosion, a subgroup of the Light Truck Frame Project Group was formed. The group comprised representatives from the North American automotive companies, test laboratories, frame manufacturers, and steel producers. As part of a comprehensive test program, the Corrosion Subgroup has completed tests on frame coatings. Using coated panels of a low carbon hot rolled and pickled steel sheet and two types of accelerated cyclic corrosion tests, seven frame coatings were tested for corrosion performance.

Electro-Motive Division of GM jointly with HRL Laboratories have developed a software tool, called TechPro, which assists in troubleshooting of diesel locomotives. The tool has been tested extensively in the field for the last two years. It has improved significantly the quality of diagnosis of locomotives. The tool is based on Graphical Probabilistic Models and Case Data Bases. We will discuss the design of the tool, its performance and will show its relevance to diagnosis of automobiles.

The Japanese Experimental Module (JEM) Pressurized Module (PM) is a facility where astronauts conduct experiments or control the total JEM facility. Inside the PM, the air composition, temperature and humidity are controlled so as to be comfortable for astronauts' activity all the time. The verification of the on-orbit performance of the functions constituting a manned space system is one of the critical points. Computational Fluid Dynamics (CFD) simulation technology is utilized to characterize and investigate the airflow in the JEM for various operating conditions. The development of a successful CFD model for International Space Station (ISS) operation is useful because there are always off-nominal and other contingency operations, which might occur and could be analyzed using an existing CFD model. This paper also presents the cabin ventilation test data obtained from the JEM flight module.

For model year 2003, the General Motors Corporation is introducing new medium duty trucks - the Chevrolet Kodiak and GMC TopKick. These new trucks replace the previous versions of the Kodiak and TopKick medium duty trucks that were introduced in 1989 and the Chevrolet and GMC 3500HD that debuted in the 1991 model year. This new series of trucks marks a clear change in General Motors' strategy in the medium duty marketplace. It emphasizes General Motors' strong commitment to the medium duty market, as well as a strong focus on customer needs, vehicle quality and reliability. This paper describes the General Motors strategy in the medium duty market, along with the history of the design and development of these new products. Finally, this paper will discuss performance to program objectives.

Airbag systems have been part of passenger car and truck programs since the mid-1980's. However, systems designed for medium and heavy duty truck applications are relatively new. The release of airbag systems for medium duty truck has provided some unique challenges, especially for the airbag sensing systems. Because of the many commercial applications within the medium duty market, the diversity of the sensing environments must be considered when designing and calibrating the airbag sensing system. The 2003 Chevrolet Kodiak and GMC TopKick airbag sensing development included significant work, not only on the development of airbag deployment events but also non-deployment events – events which do not require the airbag to deploy. This paper describes the process used to develop the airbag sensing system deployment events and non-deployment event used in the airbag sensing system calibration.

The reliability of an electronic sensor in the automotive applications is assessed using data from Fleet Test and proving ground Vehicle Endurance test. These nonfailure data are multiply censored at different mileage. Reliability analysis of data with no failure is rarely discussed in most reliability literature. This paper applies the Weibull maximum likelihood analysis based on known values of the Weibull shape parameter to extract useful reliability information. The well-known Weibayes and Weibest methods are subsets of the discussed approach. The sensitivity of the change of reliability levels over a range of Weibull shape parameter values is also examined in our case. The Huang-Porter (1991) approach of obtaining a reliability lower bound regardless of the Weibull shape parameter values is also applied and its potential of practical application is discussed. Practical limitations of all methods are discussed.

In order to design a well-balanced truck frame, optimization of not only the stiffness of the entire body and stress of each member, but also the internal force of each member is necessary, including the effect of a rear body mounted on the frame. This paper proposes a new parameter, “torsional stiffness share rate,” that directly correlates the contribution of member torsional stiffness to frame torsional stiffness with the internal force of the members as to torsion of the truck frame. The merits of the torsional stiffness share rate are shown in comparison with the strain energy share rate and the stiffness contribution rate. The results of experimental and FEM analyses of the torsional stiffness share rate are also presented.

Mud adhesion to the rear surfaces of trucks, vans and buses causes troublesome results such as aesthetic degradation, hindered rear view and laborious washing. To raise the product value of trucks and buses, it is important to develop effective measures for suppressing such mud adhesion. In this research the authors first clarified the mechanism of mud adhesion through flow visualization tests. Then, wind tunnel tests were performed to predict the effects of various countermeasures, and prospective ones were put under actual driving tests to verify their effects. The following measures were found effective in suppressing mud adhesion. (1) Aerodynamic improvement by attaching corner vanes to the upper and side edges of the rear surface. (2) Blocking road splash with a slanted plate under the truck and close to the base.

Allison Gas Turbine Division of General Motors is performing the first phase of a multiphase development project aimed at demonstrating an electric vehicle based on a proton exchange membrane (PEM) fuel cell. This work is sponsored by the Office of Transportation Technologies of the U.S. Department of Energy (DoE) through the DoE's Chicago Field Office (Contract No. DE-AC02-90CH10435). This work complements major efforts under way to produce electric vehicles for reducing pollution in key urban areas. Battery powered vehicles will initially satisfy niche markets where limited range vehicles can meet commuter needs. The PEM fuel cell/battery hybrid using methanol as fuel potentially offers an extremely attractive option to increasing the range, payload, and/or performance of battery powered vehicles.

To evaluate and refine interior architecture of the new Dodge Ram pickup truck three years before production, a road worthy interior package validation buck was built using a fiberglass body shell. Molds for the shell were made using CAD/CAM techniques. Advanced CAD/CAM techniques were used to build the interior buck of a subsequent model from individual panels molded in carbon fiber. This buck also included inner structural panels and interior trim components taken from CAD data. For this and subsequent new vehicle programs, refinement of construction techniques allows the bucks to serve as aids in product design and manufacturing feasibility studies.

Chrysler Corporation has developed an 8.0-liter engine for light truck applications. Numerous features combine to produce the highest power and torque ratings of any gasoline-fueled light truck engine currently available while also providing commensurate durability. These features include: a deep-skirt ten-cylinder 90° “V” block, a Helmholtz resonator intake manifold that enhances both low and mid-range torque, light die cast all-aluminum pistons for low vibration, a unique firing order for smooth operation, a “Y” block configuration for strength and durability, a heavy duty truck-type thermostat to control warm up, and a direct ignition system.

Chrysler Corporation's Jeep and Truck platform implemented a new design and prototype process for the body-in -white of a new pickup truck. A team approach achieved concurrent body design, stamping die design, assembly process development, and assembly tooling development. The first domestic US industry use of a 100% electronic design and release system was instrumental in the process. The new process produced a prototype body-in-white on time at 95 WBVP (weeks before volume production) with the highest level of production-intent components ever achieved within Chrysler at this stage of development.