Search Results

Hydrocarbon permeation is one of the remaining main sources of vehicle evaporative hydrocarbon emission. However, very little information exists on the role of fuel properties on permeation losses. Therefore, experimental and modeling studies were conducted to determine the relationships between hydrocarbon permeation through HDPE (high density polyethylene) and fuel properties. Half-gallon HDPE bottles without EVOH were used in this study, because they were easily available and because steady state permeation can be measured in a matter of few days instead of several months in the case of HDPE/EVOH bottles. A permeation equation was developed using both theory and experimental data, which shows that permeation increases exponentially with fuel aromatic content, increases linearly with fuel RVP, and increases exponentially with temperature. The equation is useful for predicting how fuel and ambient temperature affect hydrocarbon permeation through vehicle fuel system.

Commingling of fuels containing various concentrations of ethanol can occur in a vehicle fuel tank. It was not possible to estimate the RVPs of commingled ethanol containing fuels because they form complex non-ideal solutions. A nomograph and an equation were developed using the theory and experimental data for estimating the RVP of a commingled ethanol fuel blend from the RVPs of two base fuels containing any amounts of ethanol. The model is also useful for general purpose estimation of vapor pressures of ethanol/gasoline blends such as seasonal blending of E85 fuels with the right vapor pressure gasoline and the right amount of ethanol to meet the seasonal fuel vapor pressure requirement.

The recyclability of co-extruded multilayer fuel tanks, and characterization of the materials used in their manufacture, have been investigated. The ethylene-vinyl alcohol, EvOH, copolymer barrier layer, extruded as a sandwich between two adhesive layers of a maleated linear low density polyethylene, LLDPE, is surrounded by three high density polyethylene, HDPE, layers, one of which is composed of the regrind derived from the waste generated by manufacture. Particular attention has been focused on the mechanism of adhesion between the barrier layer and the adhesive layers. Surface analysis of the in situ surfaces has confirmed the formation of chemical bonds between the two polymers. Morphological information, concerning dispersion of the barrier layer in the HDPE matrix during recycling, has been obtained by scanning (SEM) and transmission (TEM) electron microscopy techniques.

The accurate prediction of burst of hydroformed tubes is a research area of considerable importance in order to evaluate a design before prototyping. This report applies the presently available criteria (forming limit diagram, stress-based forming limit diagram, extended stress based forming limit curve and the plastic strain criterion) to some of the benchmark examples carried out by the Auto/Steel partnership. It was found that the formability predictions are lowest if the plastic strain criterion is used and highest if either the stress-based criteria are used. Predicted and measured results were also compared.

Federal standards that mandate improved fuel economy have resulted in the increased use of lightweight materials in automotive applications. However, the environmental burdens associated with a product extend well beyond the use phase. Life cycle assessment is the science of determining the environmental burdens associated with the entire life cycle of a given product from cradle-to-grave. This report documents the environmental burdens associated with every phase of the life cycle of two fuel tanks utilized in full-sized 1996 GM vans. These vans are manufactured in two configurations, one which utilizes a steel fuel tank, and the other a multi-layered plastic fuel tank consisting primarily of high density polyethylene (HDPE). This study was a collaborative effort between GM and the University of Michigan's National Pollution Prevention Center, which received funding from EPA's National Risk Management Research Laboratory.

In the twenty-first century, exhaust emission control will remain a major technical challenge especially as additional pressures for fuel and energy conservation mount. To address these needs, a wide variety of engine and powertrain options must be considered. For many reasons, the piston engine will remain the predominant engine choice in the twenty-first century, especially for conventional and/or parallel hybrid drive trains. Emissions constraints favor the conventional port fuel-injected gasoline engine with 3-way exhaust catalyst, while energy conservation favors direct-injection gasoline and diesel engines. As a result of recent technological progress from a competitive European market, diesels, and most recently, direct-injection (DI) diesels now offer driveability and performance characteristics competitive with those of gasoline engines. In addition, DI diesels offer the highest fuel efficiency.

Nine engine oils were evaluated in two GM vehicles: a 1993 Pontiac Grand Am with a 2.3L Quad4 engine and a 1993 Buick LeSabre with a 3.8L (3800) V-6 engine. Standard EPA (Environmental Protection Agency) fuel economy (FE), vehicle-dynamometer tests were conducted. The results were compared with the fuel economy obtained with a standard ASTM reference oil (BC). The vehicle data from this program were used in evaluating the new engine-dynamometer ASTM Sequence VI-A test designed to predict “real world” fuel economy in vehicles. EPA 55/45 combined fuel economy performance in the GM vehicles ranged from almost 2 percent improvement (over the BC oil) for an SAE 5W-20 oil, to over 2 percent poorer fuel economy than the reference oil for an SAE 20W-50 oil. The two different engines responded similarly to the different oils and showed similar trends.

This paper describes a bench method to evaluate the frictional behavior, under scuffing conditions, of some test coupons of standard materials currently used in making cylinder bores and pistons. The usefulness of this method is in evaluating new materials and coatings that may enable the elimination of iron liners from engine blocks. While investigating the potential application of Plasma Source Ion Implantation (PSII) on engine piston/bore materials, we have systematically studied the scuffing related friction behavior of aluminum 390 alloy and cast iron. A pin-on-disk tribometer is used under dry sliding conditions. Testing parameters for simulating cold scuff in bench tests have been specified. This proposed test method offers a screening tool desirable for the development of PSII technology and may also be useful for the design of other new surface modification techniques.

This paper examines the potential use of diamond-like carbon (DLC) on aluminum alloy pistons of internal combustion engines. Our approach is to apply a DLC coating on the piston running against an aluminum-390 bore thus eliminating the iron liners in a standard piston/bore system. Experimental data, using a pin-on-disk tribometer under unlubricated test conditions, indicate that the performance of the DLC coating against aluminum 390 exhibits superior friction resistance compared to aluminum-390 against cast iron; the latter material couple representing the materials currently being used in production for the piston/bore application. Moreover, by thermally cycling the DLC coatings we show that improved friction and wear properties can he maintained to temperatures as high as 400°C.

ACuZinc™ 5, a GM-patented, high-performance ternary zinc-copper-aluminum alloy which is suitable for manufacturing net shape die castings, plays a vital role in the success of new automotive parts and systems. The new parts were designed to meet the auto industry's higher load and safety specifications. The superior mechanical properties of ACuZinc™ make it suitable for structural applications where commercial zinc die casting alloys have been found to be inadequate. From a business viewpoint, ACuZinc™ can help in penetrating new markets by competing for cast iron, powder metal and brass applications. ACuZinc is a registered GM trademark.

A survey of the CNG compositions within NGV driving range of Houston was performed. It was found that the statistics for the Texas CNGs were very similar to those from a previous national survey Based upon the present survey results, two extremes of CNG composition were chosen for a study of the effects of composition on emissions, fuel economy, and driveability. Two other CNG compositions were also included to provide for comparisons with the recently completed Auto/Oil Air Quality Improvement Research Program (AQIRP) and to extend the AQIRP database. One of the vehicles used in the AQIRP study was also used in the present investigation. Correlations were investigated for the relationships between the CNG composition and tailpipe emissions, fuel economy, and driveability.

Over the last two decades, advanced engine control systems have been developed that use cylinder pressure as the primary feedback variable. Production application has been limited by cost, reliability, and packaging difficulties associated with intrusive cylinder pressure sensors. Now, a low-cost cylinder-pressure-based engine control system has been developed that utilizes Pressure-Ratio Management (PRM) and non-intrusive cylinder pressure sensors mounted in the spark plug boss of four-valve-per-cylinder engines. The system adaptively optimizes individual-cylinder spark timing and air-fuel ratio, and overall exhaust gas recirculation (EGR) for best fuel economy and lowest emissions over the life of each vehicle. This paper presents the engine control and cylinder pressure sensor systems. Results are presented showing spark timing and EGR control, knock and misfire detection, cylinder-to-cylinder air/fuel balancing, and cold start control.

This paper presents an overview of techniques for measuring friction using bench tests and fired engines. The test methods discussed have been developed to provide efficient, yet realistic, assessments of new component designs, materials, and lubricants for in-cylinder and overall engine applications. A Cameron-Plint Friction and Wear Tester was modified to permit ring-in-piston-groove movement by the test specimen, and used to evaluate a number of cylinder bore coatings for friction and wear performance. In a second study, it was used to evaluate the energy conserving characteristics of several engine lubricant formulations. Results were consistent with engine and vehicle testing, and were correlated with measured fuel economy performance. The Instantaneous IMEP Method for measuring in-cylinder frictional forces was extended to higher engine speeds and to modern, low-friction engine designs.