Search Results

We assessed the engine-out emissions of an ultra-low sulfur diesel (ULSD) and a neat hydrogenated vegetable oil (HVO) from a light-duty diesel truck equipped with common rail direct injection. The vehicle was tested at least twice on each fuel using the LA-92 drive cycle and at steady-state conditions at 30 mph and 50 mph at different loads. Results showed reductions in the engine-out total hydrocarbon (THC), carbon monoxide (CO), nitrogen oxide (NOx), and particulate emissions with HVO. The reductions in soot mass, solid particle number, and particulate matter (PM) mass emissions with HVO were due to the absence of aromatic and polyaromatic hydrocarbon compounds, as well as sulfur species, which are known precursors of soot formation. Volumetric fuel economy, calculated based on the carbon balance method, did not show statistically significant differences between the fuels.

In some studies, a relationship has been observed between increasing ethanol content in gasoline and increased particulate matter (PM) emissions from vehicles equipped with spark ignition engines. The fundamental cause of the PM increase seen for moderate ethanol concentrations is not well understood. Ethanol features a greater heat of vaporization (HOV) than gasoline and also influences vaporization by altering the liquid and vapor composition throughout the distillation process. A droplet vaporization model was developed to explore ethanol’s effect on the evaporation of aromatic compounds known to be PM precursors. The evolving droplet composition is modeled as a distillation process, with non-ideal interactions between oxygenates and hydrocarbons accounted for using UNIFAC group contribution theory. Predicted composition and distillation curves were validated by experiments.

Biofuels, such as ethanol and butanol, have been the subject of significant political and scientific attention, owing to concerns about climate change, global energy security, and the decline of world oil resources that is aggravated by the continuous increase in the demand for fossil fuels. This study evaluated the potential emissions impacts of different alcohol blends on a fleet of modern gasoline vehicles. Testing was conducted on a fleet of nine vehicles with different combinations of ten fuel blends over the Federal Test Procedure and Unified Cycle. The vehicles ranged in model year from 2007-2014 and included four vehicles with port fuel injection (PFI) fueling and five vehicles with direct injection (DI) fueling. The ten fuel blends included ethanol blends at concentrations of 10%, 15%, 20%, 51%, and 83% by volume and iso-butanol blends at concentrations of 16%, 24%, 32%, and 55% by volume, and an alcohol mixture giving 10% ethanol and 8% iso-butanol in the final blend.

Gasoline direct injection (GDI) engines have improved thermodynamic efficiency (and thus lower fuel consumption) and power output compared with port fuel injection (PFI) and their penetration is expected to rapidly grow in the near future in the U.S. market. In addition, the use of alternative fuels is expanding, with a potential increase in ethanol content beyond the current 10%. Increased emphasis has been placed on butanol due to its more favorable fuel properties, as well as new developments in production processes. This study explores the influence of mid-level ethanol and iso-butanol blends on criteria emissions, gaseous air toxics, and particulate emissions from two wall-guided gasoline direct injection passenger cars fitted with three-way catalysts. Emission measurements were conducted over the Federal Test Procedure (FTP) driving cycle on a chassis dynamometer.

The paper presents reportage of the debate on the topic expressed by its title that was held as a special session at the SAE 2003 Congress, supplemented by commentaries on its highlights. The debate brought to focus the fact that fuel cells are, indeed, superb powerplants for automobiles, while hydrogen is at the pinnacle of superiority as the most refined fuel. The problems that remained unresolved, are: (1) when fuel cells will be practically viable to replace internal combustion engines and (2) under what circumstances hydrogen, as the ultimate fuel, will be economically viable in view of its intrinsically high cost and hazards engendered by its extraordinary flammability and explosive tendency.

A relationship has been observed between increasing ethanol content in gasoline and increased particulate matter (PM) emissions from direct injection spark ignition (DISI) vehicles. The fundamental cause of this observation is not well understood. One potential explanation is that increased evaporative cooling as a result of ethanol’s high HOV may slow evaporation and prevent sufficient reactant mixing resulting in the combustion of localized fuel rich regions within the cylinder. In addition, it is well known that ethanol when blended in gasoline forms positive azeotropes which can alter the liquid/vapor composition during the vaporization process. In fact, it was shown recently through a numerical study that these interactions can retain the aromatic species within the liquid phase impeding the in-cylinder mixing of these compounds, which would accentuate PM formation upon combustion.

The environmental implications of converting vehicles powered by Internal Combustion Engines (ICE) to battery powered and hybrid battery/ICE powered are evaluated for the case of Chile, one of the worldwide leaders in the production of lithium (Li) required for manufacturing of Li-ion batteries. The economic and environmental metrics were evaluated by techno-economic analysis (TEA) and Life Cycle Assessment (LCA) tools - SuperPro Designer and Gabi®/GREET® models. The system boundary includes both the renewable and nonrenewable energy sources available in Chile and well-to-pump energy consumptions and GHG emissions due to Li mining and Li-ion battery manufacturing. All the major input data required for TEA and LCA were generated using Autonomie vehicle modeling software. This study compares economic and environmental indicators of three vehicle models for the case of Chile including compact, mid-size, and a light duty truck.

Although various legislation and regulations have been adopted to promote the use of alternative-fuel vehicles for curbing urban air pollution problems, there is a lack of systematic comparisons of emission control cost-effectiveness among various alternative-fuel vehicle types. In this paper, life-cycle emission reductions and life-cycle costs were estimated for passenger cars fueled with methanol, ethanol, liquified petroleum gas, compressed natural gas, and electricity. Vehicle emission estimates included both exhaust and evaporative emissions for air pollutants of hydrocarbon, carbon monoxide. nitrogen oxides, and air-toxic pollutants of benzene, formaldehyde, 1,3-butadiene, and acetaldehyde. Vehicle life-cycle cost estimates accounted for vehicle purchase prices, vehicle life, fuel costs, and vehicle maintenance costs.

Liquefied petroleum gas (LPG), whose primary composition is propane, is a promising candidate for heavy-duty vehicle applications as a diesel fuel alternative due to its CO2 reduction potential and high knock resistance. To realize diesel-like efficiencies, spark-ignited LPG engines are proposed to operate near knock-limit over a wide range of operating conditions, which necessitates an investigation of fuel-engine interactions that leads to end-gas autoignition with propane combustion. This work presents both experimental and numerical studies of stoichiometric propane combustion in a spark-ignited (SI) cooperative fuel research (CFR) engine. Engine experiments are initially conducted at different compression ratio (CR) values, and the effects of CR on engine combustion are characterized.

Natural Gas used in high-efficiency engines holds promise as a low-cost intermediate solution to reduce Greenhouse Gases and particulate matter. However, to achieve high engine efficiencies, engines need to be operated at increased Brake Mean Effective Pressures (BMEP), which is limited by destructive, engine damaging knock. Alternatively, if controlled, the same End-Gas Autoignition (EGAI) process responsible for knock can boost efficiencies and consume unburned methane while leveraging low-cost traditional exhaust aftertreatment technologies, such as a three-way catalyst, to minimize environmental impact. For this reason, this work has developed a method to detect the presence of EGAI and to determine its onset location (or crank angle).

Research on alternative fuels has made significant progress as demands for cleaner and more efficient engine operation intensifies. Liquefied petroleum gas (LPG) can offer a potential alternative fuel route in the Diesel fuel dominated heavy-duty transportation sector due to its low cost, high anti-knock limit relative to gasoline, and reduced emission levels. In this work, experimental investigations are performed to study the effects of LPG compositions on performance, emissions, and combustion behavior of a spark-ignited (SI) cooperative fuel research (CFR) engine under stoichiometric conditions. Four LPG blends (chemically pure propane, a representative US blend, HD-5, and a representative European blend) representing the present LPG market are chosen. The impact of fuel composition is studied under different compression ratios (CR), ranging from 7:1 to 10:1 with one-unit increments, and at constant engine speed, intake manifold air pressure (IMAP) and 50% burn crank angle (CA50).

This study presents experimental and numerical examination of directly injected (DI) propane and iso-octane, surrogates for liquified petroleum gas (LPG) and gasoline, respectively, at various engine like conditions with the overall objective to establish the baseline with regards to fuel delivery required for future high efficiency DI-LPG fueled heavy-duty engines. Sprays for both iso-octane and propane were characterized and the results from the optical diagnostic techniques including high-speed Schlieren and planar Mie scattering imaging were applied to differentiate the liquid-phase regions and the bulk spray phenomenon from single plume behaviors. The experimental results, coupled with high-fidelity internal nozzle-flow simulations were then used to define best practices in CFD Lagrangian spray models.

Liquefied petroleum gas (LPG), like many other alternative fuels, has witnessed increased adoption in the last decade, and its use is projected to rise as stricter emissions regulations continue to be applied. However, much of its use is limited to dual fuel applications, gaseous phase injection, light-duty passenger vehicle applications, or scenarios that require conversion from gasoline engines. Therefore, to address these limitations and discover the most efficient means of harnessing its full potential, more research is required in the development of optimized fuel injection equipment for liquid port and direct injection, along with the implementation of advanced combustion strategies that will improve its thermal efficiency to the levels of conventional fuels.

For automotive applications, it is necessary to maximize the fuel conversion efficiency of a PEM direct-methanol fuel cell (DMFC) over the broadest possible dynamic range of power. The research reported here critically examines the efficiency of the DMFC stack when operated over a broad power range. This research establishes a basis for a control strategy that simultaneously: optimizes DMFC fuel conversion efficiency versus power level, leads into a system level optimization of efficiency vs. power, and provides an operational strategy for controlling a direct-methanol fuel cell for maximum fuel efficiency from minimum to maximum power demand. First, there is an explanation of the experimental conditions used to obtain the DMFC experimental data that is reported and analyzed. Next the DMFC methanol crossover phenomenon is discussed and characterized. Then the conceptual framework for the optimization of fuel conversion efficiency is presented.

The relationship between ethanol and iso-butanol fuel concentrations and vehicle particulate matter emissions was investigated. This study utilized a gasoline direct injection (GDI) flexible fuel vehicle (FFV) with wall-guided fueling system tested with four fuels, including E10, E51, E83, and an iso-butanol blend at a proportion of 55% by volume. Emission measurements were conducted over the Federal Test Procedure (FTP) driving cycle on a chassis dynamometer with an emphasis on the physical and chemical characterization of particulate matter (PM) emissions. The results indicated that the addition of higher ethanol blends and the iso-butanol blend resulted in large reductions in PM mass, soot, and total and solid particle number emissions. PM emissions for the baseline E10 fuel were characterized by a higher fraction of elemental carbon (EC), whereas the PM emissions for the higher ethanol blends were more organic carbon (OC) in nature.

This paper follows a cycle-simulation method for creating an engine performance map for an ethanol fueled boosted HCCI engine using a 1-dimensional engine model. Based on experimentally determined limits, the study defined operating conditions for the engine and performed a limited parameter sweep to determine the best efficiency case for each condition. The map is created using a 6-Zone HCCI combustion model coupled with a detailed chemical kinetic reaction mechanism for ethanol, and validated against engine data collected from a 1.9L 4-Cylinder VW TDI engine modified to operate in HCCI mode. The engine was mapped between engine speeds of 900 and 3000 rpm, 1 and 3 bar intake pressure, and 0.2 and 0.4 equivalence ratio, resulting in loads between idle and 14.0 bar BMEP. Analysis of a number of trends for this specific engine map are presented, such as efficiency trends, effects of combustion phasing, intake temperature, engine load, engine speed, and operating strategy.

Engine manufacturers have explored many routes to reducing the emissions of harmful pollutants and conserving energy resources, including development of after treatment systems to reduce the concentration of pollutants in the engine exhaust, using alternative fuels, and using alternative fuels with after treatment systems. Liquefied petroleum gas (LPG) is one alternative fuel in use and this paper will discuss emission measurements for several LPG vehicles. Regulated emissions were measured for five school buses, one box truck, and two small buses over a cold start Urban Dynamometer Driving Schedule (CS_UDDS), the Urban Dynamometer Driving Schedule (UDDS), and the Central Business District (CBD) cycle. In general, there were no significant differences in the gas phase emissions between the UDDS and the CBD test cycles. For the CS-UDDS cycle the total hydrocarbons and non-methane hydrocarbon emissions are higher than they are from the UDDS cycle.

Hydrotreating of vegetable oils or animal fats is an alternative process to esterification for producing biobased diesel fuels. Hydrotreated products are also called renewable diesel fuels. Hydrotreated vegetable oils (HVO) do not have the detrimental effects of ester-type biodiesel fuels, like increased NOx emission, deposit formation, storage stability problems, more rapid aging of engine oil or poor cold properties. HVOs are straight chain paraffinic hydrocarbons that are free of aromatics, oxygen and sulfur and have high cetane numbers. In this paper, NOx - particulate emission trade-off and NOx - fuel consumption trade-off are studied using different fuel injection timings in a turbocharged charge air cooled common rail heavy duty diesel engine. Tested fuels were sulfur free diesel fuel, neat HVO, and a 30% HVO + 70% diesel fuel blend. The study shows that there is potential for optimizing engine settings together with enhanced fuel composition.

Steady-state, transient and dithering characteristics of emission conversion efficiencies of three-way catalysts on natural gas IC engine were investigated experimentally on a single-cylinder CFR engine test bench. Steady-state runs were conducted as references for specific engine emission levels and corresponding catalyst capacities. The steady-state data showed that conversion of HC will be the major problem since conversion of HC was effective only for a very narrow range of exhaust mixture. Unsteady exploration runs with both lean-to-rich and rich-to-lean transitions were conducted. These results were interpreted with a time scale analysis, according to which a qualitative oxygen storage model was proposed featuring the difference between oxygen absorption and desorption rates on the palladium catalysts.