Search Results

Electro-pneumatic valve actuators are used to eliminate the cam shaft of a traditional internal combustion engine. They are used to control the opening timing, duration, and lift of both intake and exhaust valves. A physics based nonlinear mathematical model called the level one model was built using Newton's law, mass conservation and thermodynamic principles. A control oriented model, the level two model, was created by partially linearizing the level one model for model reference parameter identification. This model reduces computational throughput and enables real-time implementation. A model reference adaptive control system was used to identify the nonlinear parameters that were needed for generating a feedforward control signal. The closed-loop valve lift tracking, valve opening and closing timing control strategies were proposed.

The purpose of this paper is to demonstrate our success in taking advantage of model-based development tools and auto-code technology to accelerate the typical life cycle development of powertrain software. In particular, we applied the technology as a clean sheet approach to Visteon's third generation Electronic Throttle Control system. In the process of applying model-based development and 100% auto-code, we identified various pitfalls and created solutions to overcome the gap between technology and development process during each phase of the entire software development life cycle. We will share our lessons learned during the requirement, design, implementation, and validation stages.

This paper describes two electronic throttle controllers of Visteon Corporation with one already in production and the other currently under development. Analysis and tuning of the two controllers are described. The general structure of the controllers consists of a reference shaping subsystem and a proportional-plus-integral-plus-derivative(PID) controller supplemented with additional terms that deal with the nonlinearility of the electronic throttle body. Due to a friction cancellation term in the controller that minimizes the nonlinearity of the system, linear system analysis techniques are applied. The transfer functions of the electronic throttle body at six different operating conditions are derived. Analysis of the closed-loop dynamics is performed based on the plant and the controller transfer-functions. Controller fine-tuning is performed using frequency response techniques, MATLAB simulations and testing on the actual system.

This paper introduces the Driver Stability System (DSS) at Visteon. DSS is a new active comfort / safety system for automobiles which controls the seat bolsters independently in real time to enhance the lateral support of the occupants. Under turning maneuvers, DSS reacts to the vehicle dynamics to provide an increased contact area between the occupants and their seats, allowing optimal occupant location with respect to such variables as steering wheel angle, lateral acceleration, yaw rate, and vehicle velocity. The lateral force compensation is directly coupled to the dynamic movement of vehicle chassis and the change of road profile. The system consists of the seat bolster assembly including DC motors, wheel speed sensors, steering wheel sensor, lateral accelerometer, yaw rate sensor, and electronic control unit (ECU). This paper also discusses the control concept of DSS and its realistic controller structure.

Steer-by-wire systems (SBW) offer the potential to enhance steering functionality by enabling features such as automatic lane keeping, park assist, variable steer ratio, and advanced vehicle dynamics control. The lack of a steering intermediate shaft significantly enhances vehicle architectural flexibility. These potential benefits led GM to include steer-by-wire technology in its next generation fuel cell demonstration vehicle, called “Sequel.” The Sequel's steer-by-wire system consists of front and rear electromechanical actuators, a torque feedback emulator for the steering wheel, and a distributed electronic control system. Redundancy of sensors, actuators, controllers, and power allows the system to be fault-tolerant. Control is provided by multiple ECU's that are linked by a fault-tolerant communication system called FlexRay. In this paper, we describe the objectives for fault tolerance and performance that were established for the Sequel.

Principle of the target tracking method for the Adaptive Cruise Control (ACC) system, which is applicable to non-uniform or transient condition, had been proposed by one of the authors. This method does not need any other information rather than that from the radar and host vehicle. Here the method is modified to meet more complex traffic scenarios and then applied to data measured on real highway. The modified method is based on the phase chart between the lateral component of the relative velocity and azimuth of a preceding vehicle. From the trace on the chart, the behavior of a preceding vehicle is judged and the discrimination between the lane change and curve-entry/exit can be made. The method can deal with the lane-change of a preceding vehicle on the curve as well as on the straight lane. And it is applied to more than 20 data including several road/vehicle conditions: road is straight, or turns right or left; vehicles are motorbikes, sedans and trucks.