Search Results

The intake and exhaust port design plays a substantial role in performance of combustion systems. The port design determines the volumetric efficiency and in-cylinder charge motion of the spark-ignited engine which influences the thermodynamic properties directly related to the power output, emissions, fuel consumption and NVH properties. Thus intake port has to be appropriately designed to fulfill the required charge motion and high flow performance. While turbulence intensity and air-mixture quality affect dilution tolerance and fuel economy as a result, breathing ability affects wide open throttle performance. Traditional approaches require experimental techniques to reach a target balance between the charge motion and breathing capacity. Such techniques do not necessarily result in an optimized solution.

Stringent fuel economy and emissions regulations have driven development of new mixture preparation technologies and increased spark-ignition engine complexity. Additional degrees of freedom, brought about by devices such as cam phasers and charge motion control valves, enable greater range and flexibility in engine control. This permits significant gains in fuel efficiency and emission control, but creates challenges related to proper engine control and calibration techniques. Accurate experimental characterization of high degree of freedom engines is essential for addressing the controls challenge. In particular, this paper focuses on the evaluation of three experimental residual gas fraction measurement techniques for use in a spark ignition engine equipped with dual-independent variable camshaft phasing (VVT).

With increasingly stringent emissions regulations and concurrent requirements for enhanced engine thermal efficiency, a comprehensive characterization of the automotive gasoline fuel spray has become essential. The acquisition of accurate and repeatable spray data is even more critical when a combustion strategy such as gasoline direct injection is to be utilized. Without industry-wide standardization of testing procedures, large variablilities have been experienced in attempts to verify the claimed spray performance values for the Sauter mean diameter, Dv90, tip penetration and cone angle of many types of fuel sprays. A new SAE Recommended Practice document, J2715, has been developed by the SAE Gasoline Fuel Injection Standards Committee (GFISC) and is now available for the measurement and characterization of the fuel sprays from both gasoline direct injection and port fuel injection injectors.

External aerodynamic simulations are becoming more important because of regulatory pressures on fuel economy improvements and shorter design cycles. Experimental work is typically done on scaled models to get drag and cooling flow information. This is a time consuming process. Numerical simulations might provide a complementary path to get the answers in a timely manner. This paper discusses one such approach.

Accurate evaluation of vehicles' transient total power requirement helps achieving further improvements in vehicle fuel efficiency. When operated, the air-conditioning (A/C) system is the largest auxiliary load on a vehicle, therefore accurate evaluation of the load it places on the vehicle's engine and/or energy storage system is especially important. Vehicle simulation models, such as "Autonomie," have been used by OEMs to evaluate vehicles' energy performance. However, the load from the A/C system on the engine or on the energy storage system has not always been modeled in sufficient detail. A transient A/C simulation tool incorporated into vehicle simulation models would also provide a tool for developing more efficient A/C systems through a thorough consideration of the transient A/C system performance. The dynamic system simulation software MATLAB/Simulink® is frequently used by vehicle controls engineers to develop new and more efficient vehicle energy system controls.

The power and thermal management system (PTMS) developed by Honeywell for aircraft is an integral approach combining the functions of the auxiliary power unit (APU), emergency power unit (EPU), environmental control system (ECS), and thermal management system (TMS). The next generation PTMS discussed in this paper incorporates the new more electric architecture (MEA) and energy efficient aircraft (EEA) initiatives. Advanced system architectures with increased functionality and further integration capabilities with other systems are included. Special emphasis is given to improvements resulting from interactions with the main engine, main electric power generation, and flight actuation. The major drivers for advancement are highlighted, as well as the potential use of new technologies for turbomachinery, heat exchangers, power electronics, and electric machines. More advanced control and protection algorithms are considered.

Launch vehicles that use electric actuators for thrust vector or flight control require a safe, reliable and lightweight source of electrical power. Honeywell, working with NASA Glenn Research Center and Lockheed Martin Space Systems, has developed and successfully tested a turbine-driven electric power generation system which meets these needs. This Turbine Power Unit (TPU) uses hydrogen and oxygen propellants which react catalytically to drive a shaft-speed turboalternator mounted on foil bearings. A high-reactance permanent-magnet machine (HRPMM) was selected for this application. The power conditioning and control electronics can be located within the TPU housing and the hydrogen fuel can be used to pressurize the bearings and electronics and to regeneratively cool the machine. A brassboard unit incorporating many of these features was successfully tested at output power levels from 0 to 138 kilowatts (kW).

In this paper, an analytical procedure for prediction of shell radiated noise of air induction systems (AIS) due to engine acoustic excitation, without a prototype and physical measurement, is presented. A set of modeling and simulation techniques are introduced to address the challenges to the analytical radiated noise prediction of AIS products. A filter seal model is developed to simulate the unique nonlinear stiffness and damping properties of air cleaner boxes. A finite element model (FEM) of the AIS assembly is established by incorporating the AIS structure, the proposed filter seal model and its acoustic cavity model. The coupled acoustic-structural FEM of the AIS assembly is then employed to compute the velocity frequency response of the AIS structure with respect to the air-borne acoustic excitations.

The traditional method of engine knock detection is to compare the knock intensity with a predetermined threshold. The calibration of this threshold is complex and difficult. A statistical knock detection method is proposed in this paper to reduce the effort of calibration. This method dynamically calculates the knock threshold to determine the knock event. Theoretically, this method will not only adapt to different fuels but also cope with engine aging and engine-to-engine variation without re-calibration. This method is demonstrated by modeling and evaluation using real-time engine dynamometer test data.

This paper presents the studies on how to efficiently and easily implement ECU application algorithms using the Signal Processing Engine (SPE) of the Copperhead microcontroller. With the introduced development and testing concepts and methods, users can easily establish their own PC based SPE emulation system. All application unit testing and verification work for the fixed point implementation using SPE functions can be easily conducted in PC without relying on a costly real time test bench and expensive third party dedicated software. With this simple development environment, the code can be run in both embedded controllers and PCs with exact bit to bit numerical behavior. The paper also demonstrates many other benefits such as code statistics information retrieval, floating simulation mode, automated code verification, online and offline code sharing.

The requirement of reduced emissions and improved fuel economy led the introduction of direct-injection (DI) spark-ignited (SI) engines. Dual-fuel injection system (direct-injection and port-fuel-injection (PFI)) was also used to improve engine performance at high load and speed. Ethanol is one of the several alternative transportation fuels considered for replacing fossil fuels such as gasoline and diesel. Ethanol offers high octane quality but with lower energy density than fossil fuels. This paper presents the combustion characteristics of a single cylinder dual-fuel injection SI engine with the following fueling cases: a) gasoline for PFI and DI, b) PFI gasoline and DI ethanol, and c) PFI ethanol and DI gasoline. For this study, the DI fueling portion varied from 0 to 100 percentage of the total fueling over different engine operational conditions while the engine air-to-fuel ratio remained at a constant level.

During initial phases of vehicle development process, it is usually required to understand the temperature profile for all components. It is usually more effective and less costly if the thermal issues are determined and addressed before actual vehicles are built. Computational Fluid Dynamics (CFD) analysis tools are typically used for thermal management of the vehicle environment. However, for transient thermal analysis problems, running a full CFD requires solving the mass, momentum, and energy equations. This typically requires a lengthy computation time and extensive computer resources. The problem becomes more challenging when trying to conduct CFD analysis for several design iterations and for different duty cycles that may be of a transient nature. Therefore, the application of one-dimensional analysis early in the development phase can help point out the areas of prime concern.

Based on Woodbury-Sherman-Morrison formula, a general and efficient method for torsional damper tuning is presented. This method is based on exact calculation of the resulting Frequency Response Functions (FRF's) of the system with the damper by using the original (old) FRF's of the original (baseline) system and the damper's parameters (the mass polar moment of inertia, stiffness and damping coefficient). The only requirement for this method is to have the baseline FRF's at the active points of the structure where the damper is to be attached and those point where the resulting FRF's are of interest. The baseline FRF's can be obtained by either analytical or experimental methods. Once this requirement is met, all possible scenarios of the dampers for their potential and feasibility can be efficiently evaluated before being put into service without the need for costly hardware modification and test cycles on actual structure.

Tuned mass dampers (TMDs) or vibration absorbers are widely used in the industry to address various NVH issues, wherein, tactile-vibration or noise mitigation is desired. TMDs can be classified into two categories, namely, tuned-to-resonance and tuned-to-discrete-excitation. An overwhelming majority of TMD applications found in the industry belong to the tuned-to-resonance category, so much of information is available on design considerations of such dampers; however, little is published regarding design considerations of dampers tuned-to-discrete-excitation. During this study, a problem was solved that occurred at a discrete excitation frequency away from the primary resonance frequency of a steering column-wheel assembly. A solution was developed in multiple stages. First the effects of various factors such as mass and damping were analyzed by using a closed-form solution.

A fundamental problem in the development of automotive thermal protection strategies is the understanding of the effect of time and temperature on vehicle components life and their performance throughout the life of the vehicle. Due to restrictions on emissions and the stringent requirements for improved fuel economy, the use of polymers and synthetic materials has been widely adopted in automotive applications. It is therefore critical to develop a process to estimate life of engineering materials based on thermal testing and material physical properties. While a series of carefully selected vehicle tests can determine components temperatures during different testing conditions, a need still exists to determine the expected component life and performance throughout the life of the vehicle. Kinetic models have been widely used, in literature, to determine the aging of polymeric and composite materials over time.

As global automobile manufacturers prepare for the phase-out of R134a in Europe, they must address the issue of using the new refrigerant for European sales only or launching the product worldwide. Several factors play into this decision, including cost, service, risk, customer satisfaction, capacity, efficiency, etc. This research effort addresses the minimal vehicle-level hardware differences necessary to provide a European solution of R1234yf while continuing to install R134a into vehicles for the rest of the world. It is anticipated that the same compressor, lubricant and condenser; most fluid transport lines; and in most cases the evaporator can be common between the two systems.

An experiment was conducted testing a powertrain package consisting of a four cylinder four valve engine coupled to a four speed automatic transmission in a dynamometer test cell. Cylinder pressure transducers, an encoder, and other instrumentation were used to measure transient combustion events. The transient cycle chosen for testing was a Cold 80 of the Federal Test Procedure (FTP) that produces a standardized fuel economy value. After analyzing the combustion events, a determination was made between the spark advance delivered and a revised spark advance for optimum combustion efficiency. Based upon the relationship between spark advance and fuel consumption, a prediction for the improved fuel consumption was made. The testing was then repeated to evaluate the revised spark advance and the fuel economy benefits in comparison to the predicted values.

This paper focuses on the numerical investigation of the mixing and combustion of ethanol and gasoline in a single-cylinder 3-valve direct-injection spark-ignition engine. The numerical simulations are conducted with the KIVA code with global reaction models. However, an ignition delay model mitigates some of the deficiencies of the global one-step reaction model and is implemented via a two-dimensional look-up table, which was created using available detailed kinetics models. Simulations demonstrate the problems faced by ethanol operated engines and indicate that some of the strategies used for emission control and downsizing of gasoline engines can be employed for enhancing the combustion efficiency of ethanol operated engines.

Ring gear bolts in differentials are often modified in size to accommodate the additional clamp load that is required due to an increase in torque from a vehicle's powertrain. Depending on a given program several constraints need to be considered. These include cost, validation time, reliability / durability and timing for implementation. In this paper, a Finite Element Analysis (FEA) procedure for analyzing stresses in ring gear bolts within a rear differential assembly is outlined and the computational results are then compared to quasi-static bench test results that were developed to measure bending and tension loads in the ring gear bolts during loading and unloading of the axle pinion. A dynamometer test is then developed to duplicate the failure mode and provide a comparison of the design changes proposed and the expected improvement in durability.

Because combustion engine equipped vehicles must conform to stringent hydrocarbon (HC) emission requirements, many of them on the road today are equipped with an engine air intake system that utilizes a hydrocarbon adsorber. Also known as HC traps, these devices capture environmentally dangerous gasoline vapors before they can enter the atmosphere. A majority of these adsorbers use activated carbon as it is cost effective and has excellent adsorption characteristics. Many of the procedures for evaluating the adsorbtive performance of these emissions devices use mass gain as the measurand. It is well known that activated carbon also has an affinity for water vapor; therefore it is useful to understand how well humidity must be controlled in a laboratory environment. This paper outlines investigations that were conducted to study how relative humidity levels affect an activated carbon hydrocarbon adsorber.