Search Results

Partly competing objectives, as low fuel consumption, low friction, long oil maintenance rate, and at the same time lowest exhaust emissions have to be fulfilled. Diminishing resources, continuously reduced development periods, and shortened product cycles yield detailed knowledge about oil consumption mechanisms in combustion engines to be essential. There are different ways for the lubricating oil to enter the combustion chamber: for example as blow-by gas, leakage past valve stem seals, piston rings (reverse blow-by) and evaporation from the cylinder liner wall and the combustion chamber. For a further reduction of oil consumption the investigation of these mechanisms has become more and more important. In this paper the influence of the mixture formation and the resulting fuel content in the cylinder liner wall film on the lubricant oil emission was examined.

Direct injection (DI) of compressed natural gas (CNG) is a promising technology to increase the indicated thermal efficiency of internal combustion engines (ICE) while reducing exhaust emissions and using a relatively low-cost fuel. However, design and analysis of DI-CNG engines are challenging because supersonic gas jet emerging from the DI injector results in a very complex in-cylinder flow field containing shocks and discontinuities affecting the fuel-air mixing. In this article, numerical simulations are used supported by validation to investigate the direct gas injection and its influence on the flow field and mixing in an optically accessible ICE. The simulation approach involves computation of the in-nozzle flow with highly accurate Large-Eddy Simulations, which are then used to obtain a mapped boundary condition. The boundary condition is applied in Unsteady Reynolds Averaged Navier-Stokes simulations of the engine to investigate the in-cylinder velocity and mixing fields.

Direct injection (DI) compressed natural gas (CNG) engines are emerging as a promising technology for highly efficient and low-emission engines. However, the design of DI systems for compressible gas is challenging due to supersonic flows and the occurrence of shocks. An outwardly opening poppet-type valve design is widely used for DI-CNG. The formation of a hollow cone gas jet resulting from this configuration, its subsequent collapse, and mixing is challenging to characterize using experimental methods. Therefore, numerical simulations can be helpful to understand the process and later to develop models for engine simulations. In this article, the results of high-fidelity large-eddy simulation (LES) of a stand-alone injector are discussed to understand the evolution of the hollow cone gas jet better.

Oxygenates, such as methanol or ethanol, are frequently used as blending components in standard gasoline. One oxygenate, dimethyl ether (DME), is also used as a fuel component in some regions of the world, for example in Asia. In addition, patent reviews show the potential of DME as a blending component in liquefied petroleum gas (LPG) or mixed with propane. The laminar burning velocity is one key parameter for the numerical simulation of gasoline engine combustion processes. Therefore, it is of great interest for modern engine development to understand the effect of oxygenates on the laminar burning velocity. The experimental results have been conducted under engine-like conditions with elevated initial pressures of up to 20 bar and initial temperatures of 373 K. Experiments were done at equivalence ratios between 0.8 and 1.3. The experimental setup consists of a spherical closed pressurized combustion vessel with optical access.

Increasing concern for the environment and the impending scarcity of fossil fuels requires continued development in hydrocarbon combustion science. For compression-ignition engines, adding oxygenated compounds to the fuel can reduce noise, soot formation, and unburned hydrocarbons while simultaneously increasing thermal efficiency. In order to reliably model and design compression-ignition engines to use new fuel blends, accurate spray characteristic data is required. In this study, the spray characteristics of various blends of the oxygenated compound di-n-butyl ether (DNBE) with standard EN590 Diesel fuel are presented, including spray cone angle and spray penetration length for both liquid and gas phases. The experiments were conducted in a spray chamber at ambient conditions of 50 bar and 800 K, simulating TDC conditions in a Diesel engine. Injection pressures were varied from 700-1600 bar.

Since the CO2 emissions of passenger car traffic and their greenhouse potential are in the public interest, natural gas (CNG) is discussed as an attractive alternative fuel. The engine concepts that have been applied to date are mainly based upon common gasoline engine technology. In addition, in mono-fuel applications, it is made use of an increased compression ratio -thanks to the RON (Research Octane Number) potential of CNG-, which allows for thermodynamic benefits. This paper presents advanced engine concepts that make further use of the potentials linked to CNG. Above all, the improved knock tolerance, which can be particularly utilized in turbocharged engine concepts. For bi-fuel (CNG/gasoline) power trains, the realization of variable compression ratio is of special interest. Moreover, lean burn technology is a perfect match for CNG engines. Fuel economy and emission level are evaluated basing on test bench and vehicle investigations.

SI engines with gasoline direct injection are currently the focus of development for almost all car manufacturers. After the introduction of DISI engines, first to the Japanese market and after a short time delay also in Europe, a broad variety of technical solutions for efficient stratified concepts can be stated. The targets of the development activities in this field are defined by legislation and customer's demands. The potential reduction of fuel consumption with stratified operation has to be combined with a further improvement of the full load potential of the DISI engine. A substantial part of the development activities are the fulfillment of current and future emission standards. Therefore, in order to realize a highly efficient lean operation, new technologies and strategies in the field of exhaust gas aftertreatment and vehicle application are required.

Like all technical fluids, lubricants are able to solve gases. While solved gas is a neutral part of the lubricant, dissolved gas has an influence especially on the compressibility behavior. The effects of oil aeration on engine drive causes malfunctions of several components. A successful optimization of the oil circulation concerning the oil aeration presupposes a safe and reproducible measuring procedure. The FEV has developed a measurement apparatus according to the principle of the volume measurement which allows a simple but efficient oil aeration measurement.

Today, SULEV legislation represents the most stringent emission standard for vehicles with combustion engines, and it will be introduced starting by Model Year 2003. In order to meet such standards, even higher effort is required for the development of the exhaust gas emission concept of SI engines. Beyond a facelift of the combustion system, exhaust gas aftertreatment, and the engine management system, new approaches are striven for. The principle keys are well known: low HC feed gas, high thermal load for quick light-off, exhaust system with low heat capacity and highly effective exhaust gas aftertreatment.

With regard to increasingly stringent emission legislation natural gas is gaining interest as an alternate fuel. Concerning mobile application natural gas is often considered to produce potentially lower exhaust emissions compared to diesel and gasoline fuel. Nevertheless, also the exhaust gas of diesel and gasoline fuelled vehicles will be improved by applying advanced technical solutions. The paper reveals the state-of-the-art in exhaust emission behaviour of diesel, gasoline, liquified petroleum gas and natural gas fuelled vehicles. Passenger cars and light-duty trucks will be considered as well as HD-trucks. Emissions include NOx, THC, NMHC, CO, Aldehydes and PAH. In addition CH4 and CO2 emissions are discussed with respect to increasing concern about the greenhouse effect. From the viewpoint of the HD-engines the alternate fuels Dimethylether (DME) and Diesel/water-Emulsion are also considered.

This paper focuses on start-up technology for fuel processing systems with special emphasis on gasoline fueled burners. Initially two different fuel processing systems, an autothermal reformer with preferential oxidation and a steam reformer with membrane, are introduced and their possible starting strategies are discussed. Energy consumption for preheating up to light-off temperature and the start-up time is estimated. Subsequently electrical preheating is compared with start-up burners and the different types of heat generation are rated with respect to the requirements on start-up systems. Preheating power for fuel cell propulsion systems necessarily reaches up to the magnitude of the electrical fuel cell power output. A gasoline fueled burner with thermal combustion has been build-up, which covers the required preheating power.

In view of limited crude oil resources, alternative fuels for internal combustion engines are currently being intensively researched. Synthetic fuels from natural gas offer a promising interim option before the development of CO2-neutral fuels. Up to a certain degree, these fuels can be tailored to the demands of modern engines, thus allowing a concurrent optimization of both the engine and the fuel. This paper summarizes investigations of a Gas-To-Liquid (GTL) diesel fuel in a modern, post-EURO 4 compliant diesel engine. The focus of the investigations was on power output, emissions performance and fuel economy, as well as acoustic performance, in comparison to a commercial EU diesel fuel. The engine investigations were accompanied by injection laboratory studies in order to assist in the performance analyses.

Reduced resources of mineral oil and growing world energy consumption will increase the demand for alternative energies. Natural gas is gaining interest due to the worldwide ratio of assured reserves of natural gas and crude oil shifting towards natural gas. The main motivation for the use of gas are oil substitution, source diversification and independency of fuel supply as well as the reduction of greenhouse gases especially CO2. Natural gas operation usually reduces the torque of a naturally aspirated engine due to fuel properties. The paper shows that an optimization of a naturally aspirated engine layout can reduce the loss significantly. Besides compression ratio optimization also intake manifold and camshaft redesign for natural gas specific application can reduce the torque loss to a minimum. Super charging or turbo charging of spark ignition engines can effectively overcome the torque loss.

In the recent years, it has become obvious that one of the main fields of interest in alternate fuels is the public transportation sector. Natural Gas seems to be advantageous. It is available and environmentally friendly, even if the greenhouse effect of methane is considered. The operation range of vehicles running on CNG (Compressed Natural Gas) is poor due to the large pressure vessels, but in case of urban buses with low daily mileage this is acceptable. On the other hand, the use of an environmentally friendly fuel is favorable especially in urban areas. Although there are some advantages of Natural Gas, diesel buses dominate the market. The reason is the better part-load fuel efficiency of the Diesel principle which is superior to the Otto-cycle due to the absence of engine throttling. The efficiency levels of Spark-Ignition (SI) -type, Lean Burn Natural Gas engines are quite comparable to diesel engines during full load conditions.

Today, natural gas engines for stationary and vehicular applications are not only faced with stringent emission legislation, but also with increasing requirements for power density and efficient fuel consumption. For vehicular use, downsizing is an advantageous approach to lowering on-road fuel consumption and making gas engines more competitive with their diesel counterparts. In SI-engines, the power density at a given compression ratio is limited by knocking, or NOx emissions. A decrease in compression ratio, lowering both NOx emissions and the risk of knocking combustion, increases fuel consumption. An increase in air-fuel-ratio, required to avoid knocking at higher thermal loading, increases boost pressure, HC and CO emissions, and mechanical loading and causes the danger of misfiring. As a result, the performance of the latest production gas engines for vehicles remains at a BMEP of 18…20 bar with a NOx emission level of 2…5 g/kWh.

The efficient operation of powertrain test benches in research and development is strongly influenced by the state of “health” of the functional test object. Hence, the use of Early Damage Detection Systems (EDDS) with Unit Under Test (UUT) monitoring is becoming increasingly popular. An EDDS should primarily avoid total loss of the test object and ensure that damaged parts are not completely destroyed, and can still be inspected. Therefore, any abnormality from the standard test object behavior, such as an exceeding of predefined limits, must be recognized at an early testing time, and must lead to a shutdown of the test bench operation. With sensors mounted on the test object, it is possible to isolate the damage cause in the event of its detection. Advanced EDDS configurations also optimize the predefined limits by learning new shutdown values according to the test object behavior within a very short time.

This paper focusses on the supply conditions of a connecting rod bearing. Thereto, a novel simulation approach is presented, which is based on a transient 3D-CFD multiphase flow simulation including the ability of gas dissolution and diffusive mass transfer. The model determines the pressure behavior and the gas bubble development in the oil supply system of a connecting rod bearing. It allows to visualize the flow behavior and the existence of gas bubbles in order to get a detailed impression of the physical occurrences. The experimental results from Maaßen [5], where a big gas bubble is formed in the supply bore by gas cavitation, are confirmed and used for validation. Further the flow behavior of free air ratios is investigated. The paper concludes that the supply conditions of a connecting rod bearing are strongly influenced by the gas bubble in terms of the fluid composition and the volume flow rate at the connecting rod bearing inlet.