Search Results

In this paper, a model-based linear estimator and a non-linear control law for an Fe-zeolite urea-selective catalytic reduction (SCR) catalyst for heavy duty diesel engine applications is presented. The novel aspect of this work is that the relevant species, NO, NO2 and NH3 are estimated and controlled independently. The ability to target NH3 slip is important not only to minimize urea consumption, but also to reduce this unregulated emission. Being able to discriminate between NO and NO2 is important for two reasons. First, recent Fe-zeolite catalyst studies suggest that NOx reduction is highly favored by the NO 2 based reactions. Second, NO2 is more toxic than NO to both the environment and human health. The estimator and control law are based on a 4-state model of the urea-SCR plant. A linearized version of the model is used for state estimation while the full nonlinear model is used for control design.

This paper presents a compact temperature control device to cool down hot exhaust gas coming out of an aftertreatment emission control system. Active DPF (Diesel Particulate Filter) regeneration is required for aftertreatment emission controls to meet the 2007 EPA (Environmental Protection Agency) PM(Particulate Matter) standard. However, regeneration of the DPF temporarily elevates temperatures in the filter to eliminate accumulated soot. This can increase the temperature of the exhaust gas. The temperature control device in this paper draws ambient air into the hot exhaust stream and mixes them together in such a fashion to maximize temperature drop and minimize back pressure for a limited space without any moving parts or supply of extra power. The simple and compact design of the device makes it a cost-effective candidate to retrofit to an existing aftertreatment system.

A bridged valve train configuration exhibits complex dynamic behavior due to the uniqueness of the special elephant foot/bridge/valve structure. Consequently, this system arrangement presents significant design challenges in system stability at high speed, high load, wear, no-follow and valve seating velocity, etc. An efficient way to gain a thorough understanding of the behavior of this type of valve train system and to drive the valve train design improvement is through the use of an effective dynamic simulation tool. In this paper, an advanced CAE tool developed by Ford Motor Company for the bridged type valve train simulations has been described. This automated CAE tool provides a complete virtual ADAMS-based simulation environment for the pushrod bridged valve train system analysis. This paper also presents the correlation and validation between the simulations and the measurements. The design analysis for the bridged valve train has been discussed briefly in this paper.

The successful development of new products is contingent on clearly understanding product requirements and defining appropriate design activities to deliver the right product. Even if one can clearly understand the abstract requirements implied by the voice-of-customer (VOC), engineers still work best to a set of specifications that define the product in objective measures. The task of extracting the systems specifications from text versions of product requirements is not trivial. Full order dynamic models of mass, springs and dampers provide understanding of vehicle performance; however, the engineer has to define the dynamic characteristics based on his understanding of requirements and translate them into technical specifications. The result can be too dependent on human assumptions and judgments at this point. This work was done to understand how to apply Object Oriented Design (OOD) methodology to trace requirements of a mechanical system to design parameters.

In the present work computational fluid dynamics (CFD) simulations of the flow field around a generic tractor-trailer truck are presented and compared with corresponding experimental measurements. A generic truck model was considered which is a detailed 1/8th scale replica of a Class-8 tractor-trailer truck. It contained a number of details such as bumpers, underbody, tractor chassis, wheels, and axles. CFD simulations were conducted with wind incident on the vehicle at 0 and 6 degree yaw. Two different meshing strategies (tet-dominant and hex-dominant) and three different turbulence models (Realizable k-ε, RNG k-ε, and DES) are considered. In the first meshing strategy an unstructured tetrahedral mesh was created over a large region surrounding the vehicle and in its wake. In the second strategy the mesh was predominantly hexahedral except for a few narrow regions around the front end and the underbody which were meshed with tetrahedral cells owing to complex topology.

A droplet deformation and rotation model (DDR) has been developed and implemented in the KIVA II CFD code for better describing characteristics of liquid fuel sprays in diesel engines, including the distribution of sprays in combustion chamber space and the spray/wall impingement. The DDR model accounts for the effects of both the droplet's frontal area and its drag coefficient as a function of its deformation and rotation on droplet drag and droplet breakup. Therefore, the DDR model can be used for calculating the fuel droplet's drag and breakup in the process of combustion in diesel engines. This makes it possible to model the highly distorted droplet's frontal area variation and its effect on the drag coefficient in sprays. The new version of the KIVA II code with the DDR model has been tested for a case of the spray/wall impingement and a case of the combustion process in a diesel engine.

The purpose of this paper is to describe a methodology that significantly enhances the process of truck underhood thermal management by utilizing state-of-the-art computer simulation of airflow and heat transfer. The traditional approach has been to package underhood components in the vehicle design phase based on past experience, build a prototype, test it, analyze the test results and determine any necessary design changes. The design changes are implemented and the cycle is repeated until an acceptable design is achieved. The alternative methodology, described in this paper, uses a complete 3-D CAD model of all pertinent underhood components of a heavy-duty truck with a general purpose Computational Fluid Dynamics (CFD) code to simulate underhood airflow. The heat exchangers were modeled using an approach that divides the heat exchanger core into cell zones and computes heat rejection cumulatively from zone to zone.