Search Results

Multiple plate disc clutches are used extensively for shifting gears in automatic transmissions. In the active clutches that engage or disengage during a shift the automatic transmission fluid (ATF) and friction material experience large changes in pressure, P, sliding speed, v, and temperature, T. The coefficient of friction, μ, of the ATF and friction material is a function of these variables so μ = μ(P,v,T) also changes during clutch engagement. These changes in friction coefficient can lead to noise or vibration if the ATF properties and clutch friction material are improperly matched. A theoretical understanding of what causes noise, vibration and harshness (NVH) in shifting clutches is valuable for the development of an ATF suitable for a particular friction material. Here we present a theoretical model that identifies the slope, ∂μ/∂T, of the coefficient of friction with respect to temperature as a major contributor to the damping in a clutch during engagement.

The torsional natural frequencies of axles equipped with limited slip differential clutches depend on whether or not the tires and clutches are slipping since the effective inertia at each end of the axle is different for slipping and non-slipping conditions. Limited slip axle vibrations are typically analyzed for one tire slipping and the other not since that is the case for which the limited slip clutches are used. Vibrations often arise, however, during normal turning when both drive tires have good traction.

Kettering University's entry in the 2003 Clean Snowmobile Challenge entails the installation of a fuel injected four-stroke engine into a conventional snowmobile chassis. Exhaust emissions are minimized through the use of a catalytic converter and an electronically controlled closed-loop fuel injection system, which also maximizes fuel economy. Noise emissions are minimized by the use of a specifically designed engine silencing system and several chassis treatments. Emissions tests run during the SAE collegiate design event revealed that a snowmobile designed by Kettering University produces lower unburned hydrocarbon (1.5 to 7 times less), carbon monoxide (1.5 to 7 times less), and oxides of nitrogen (and 5 to 23 times less) levels than the average automobile driven in Yellowstone National Park. The Kettering University entry also boasted acceleration performance better than the late-model 500 cc two-stroke snowmobile used as a control snowmobile in the Clean Snowmobile testing.

Impinging jets are an established technique for obtaining high local heat transfer coefficients between a fluid and a surface. Factors such as jet attachment, surface angle, jet angle, separation distance between jet orifice and surface of impingement, and trajectory influence heat transfer dramatically. In the current study, the specific application of interest is air issuing from the defroster's nozzles of a vehicle and impinging on a glass windshield. The current work is aimed at studying the flow patterns off a vehicle windshield as a result of air issuing from various nozzle configurations. The effects of openings' geometry (circular vs rectangular), number of openings, angle that the windshield makes with the horizontal plane and angle of impinging jet, on windshield heat transfer is examined. An optimal configuration will be recommended for better heat transfer.

The transmission mount in a powertrain mounting system is often a primary path for noise. This is especially the case when the transmission is mounted directly to the body without the benefit of a structural frame or isolation between the bracket and body. Since most transmissions generate frequencies above 150Hz, the transmission mount system becomes a likely noise path for this and higher frequencies. A combination of very stiff transmission bracket and very soft rubber mount between the transmission bracket and the transmission would help this problem. In this paper the development an optimally designed transmission mount for a longitudinally mounted powertrain is presented. The development procedure of such a design considers the transmission mount as part of the total system.

A vehicle’s performance and fuel economy plays an important role in obtaining a larger market share in the segment. This can be best achieved by optimizing the aerodynamics of the vehicle. Aerodynamics can be improved by altering the bodylines on a vehicle. Its drag coefficient can be maintained at a minimum value by properly designing various component profiles. The stability of a vehicle and Passenger comfort are affected by wind noise that is related to the aerodynamics of a vehicle. To study the effects of the above-mentioned parameters, the vehicle is tested inside a wind tunnel. In this paper, the authors study the body profile for different vehicles and analyze them using Computational Fluid Dynamics software - FLUENT. To study the influence of different body profiles on drag coefficient, 3 different vehicle segments are considered.

Kettering University's entry in the 2002 Clean Snowmobile Challenge involves the installation of a fuel injected four-stroke engine into a conventional snowmobile chassis. Exhaust emissions are minimized through the use of a catalytic converter and an electronically controlled closed-loop fuel injection system, which also maximizes fuel economy. Noise emissions are minimized by the use of a specifically designed engine silencing system and several chassis treatments. Emissions tests run during the SAE collegiate design event revealed that a snowmobile designed by Kettering University produces lower unburned hydrocarbon (1.5 to 7 times less), carbon monoxide (1.5 to 7 times less), and oxides of nitrogen (and 5 to 23 times less) levels than the average automobile driven in Yellowstone National Park. The Kettering University entry also boasted acceleration performance better than the late-model 500 cc two-stroke snowmobile used as a control snowmobile in the Clean Snowmobile testing.

A coupler has been developed to prevent windshield wiper systems from being damaged by excessive loads that can occur when the normal wiping pattern is restricted. The coupler is composed of a pultruded composite rod with injection-molded plastic spherical joints (a.k.a. sockets) attached at either end. The sockets are used to attach the coupler to the crank and rocker of the windshield wiper linkage. Because the loads exerted on a coupler vary in magnitude and direction during a wiping cycle, the joint between the sockets and the pultruded composite rod must be robust. The paradigm for attaching sockets to steel couplers (i.e. over-molding the sockets around holes stamped into the ends of traditional steel couplers) was applied to the pultruded rods, tested, and found to produce inadequate joint strength. This paper details the methodology that was employed to produce and optimize an acceptable means to attach the injection-molded sockets to the pultruded rods.

Large hood mounted plastic trim components are subjected to complex and often extreme loading conditions. Typical loading conditions include solar and thermal cycling, as well as road and powertrain induced vibrations, aero lift and buffeting, and mechanical loads such as car wash. For the above components understanding and classifying the typical loading conditions is an essential and important step in achieving long term quality. This paper discusses different approaches to the design, analysis, development, and testing of plastic trim components. Samples of analysis and test results are presented to demonstrate how to identify and prevent the loss of the part function. Some useful guidelines and practices for addressing thermal expansion, dimensional variation, and redundancy in attachments are also discussed.

Doors inside an automotive HVAC module are essential components to ensure occupant comfort by controlling the cabin temperature and directing the air flow. For temperature control, the function of a door is not only to close/block the airflow path via the door seal that presses against HVAC wall, but also control the amount of hot and cold airflow to maintain cabin temperature. To meet the stringent OEM sealing requirement while maintaining a cost-effective product, a “V-Shape” soft rubber seal is commonly used. However, in certain conditions when the door is in the position other than closed which creates a small gap, this “V-Shape” seal is susceptible to the generation of objectionable whistle noise for the vehicle passengers. This nuisance can easily reduce end-customer satisfaction to the overall HVAC performance.

Kettering University's Clean Snowmobile Challenge student design team has developed a new robust and innovative snowmobile for the 2005 competition. This snowmobile dramatically reduces exhaust and noise emissions and improves fuel economy compared with a conventional snowmobile. Kettering University has utilized a modified snowmobile in-line four cylinder, four-stroke, engine. The team added an electronically-controlled fuel-injection system with oxygen sensor feedback to this engine. This engine has been installed into a 2003 Yamaha RX-1 snowmobile chassis. Exhaust emissions have been further minimized through the use of a customized catalytic converter and an electronically controlled closed-loop fuel injection system. A newly designed and tuned exhaust as well as several chassis treatments have aided in minimizing noise emissions.

Sliding contact between friction surfaces occurs in numerous torque transfer elements: torque converter clutches, shifting clutches, launch or starting clutches, limited slip differential clutches, and in the meshing of gear teeth under load. The total temperature in a friction interface is the sum of the equilibrium temperature with no sliding and a transient temperature rise, the flash temperature, caused by the work done while sliding. In a wet shifting clutch the equilibrium temperature is typically the bulk oil temperature and the flash temperature is the temperature rise during clutch engagement. The flash temperature is an important factor in the performance and durability of a clutch since it affects such things as the reactivity of the sliding surfaces and lubricant constituents (e.g., oxidation) and thermal stress in the components. Knowing how high the flash temperature becomes is valuable for the formulation of ATF, gear oil, engine oil and other lubricants.

Multiple plate disk clutches are used extensively for shifting gears in automatic transmissions. In a shift from one gear to another one or more clutches is engaging or disengaging. In these active clutches the automatic transmission fluid (ATF) and friction material experience large changes in pressure P, temperature T, and sliding speed v. The coefficient of friction, μ, of the ATF and friction material depends on v, P and T, and also changes during clutch engagement. Changes in μ can lead to vibration and poor shift quality if the ATF and clutch friction material are improperly selected. An in-depth theoretical understanding of the cause of vibration in shifting clutches is crucial in the development of a suitable ATF to work with a particular friction material.

Aerodynamics of trucks and other high sided vehicles is of significant interest in reducing road side accidents due to wind loading and in improving fuel economy. Recognizing the limitations of conventional wind tunnel testing, considerable efforts have been invested in the last decade to study vehicle aerodynamics computationally. In this paper, a three-dimensional near field flow analysis has been performed for axial and cross wind loading to understand the airflow characteristics surrounding a truck-like bluff body. Results provide associated drag for the truck geometry including the exterior rearview mirror. Modifying truck geometry can reduce drag, improving fuel economy.

The objective of this paper is to determine the whirling bending critical speeds of pultruded composite shafts in simply supported boundary conditions. Theoretical studies have been carried using Patran to determine the natural frequencies and the mode shapes for the Jeffcot and Kikuchi rigid rotor models. A tabletop experimental apparatus has been fabricated and the bending critical speeds have been measured for various span lengths between the supports. The results of this study may be useful in identifying whether pultruded composite shafts can be employed as drive shafts in automotive or other industries.

A model and simulation results are presented for the torsional dynamics of a rear wheel driveline while the vehicle is coasting in a turn. The model includes the effects of road load and powertrain drag, limited slip differential clutch friction, the inertias of the vehicle, wheels, axles, differential carrier, and driveshaft, the final drive ratio, torsional stiffnesses of the axles and driveshaft, vehicle track width, and radius of the turn. The dynamics of coasting in a turn differ from powered driving due to changes in the inertia loading the driveshaft, the damping effect of the disengaged transmission, and nonlinearities in the clutch friction. Specific focus is given to vibration in the axles and driveshaft due to variations in the torque-speed slope of the clutches, which is determined by the slope of the friction coefficient ‘μ’ versus sliding speed ‘v’ in the limited slip clutches.