Search Results

The development of highly boosted and high compression spark-ignition engines with enhanced thermal efficiencies is primarily limited by knock and super-knock. Super-knock is an excessively high intensity knock which has been related to a developing detonation process. This study investigates the knocking tendency of different gasoline surrogate fuels with varying research octane numbers (RON), octane sensitivity (S) and composition. The ξ/ɛ diagram with an enclosed detonation peninsula is used to assess the knocking tendency of different fuels. The diagram plots ξ, the ratio of acoustic to auto-ignitive velocity, against ɛ, the ratio of the transit time of an acoustic wave through a hot spot, to the heat release time (τe). Constant volume simulations of auto-ignition delay times (τi) and excitation times (τe) obtained from chemical kinetic calculations, enable calculations of ξ and ɛ.

Over the years, spark-ignition engine operation has changed significantly, driven by many factors including changes in operating conditions. The variation in operating conditions impacts the state of the end-gas, and therefore, its auto-ignition. This can be quantified in terms of K-factor, which weighs the relative contribution of Research Octane Number (RON) and Motor Octane Number (MON) to knocking tendency at any operating condition. The current study investigates the fuel requirements when operating an engine at increasing intake air pressures. A model engine was operated at varying intake air pressure in GT-Power software, from naturally aspirated intake air to heavily boosted intake air pressure of 4 bar absolute. The pressure-temperature information from the GT-Power model was used to calculate ignition delay times of the unburnt end-gas composed of a sensitive and a non-sensitive fuel in ChemKin software.

Commercial gasoline fuels are complex mixtures of numerous hydrocarbons. Their composition differs significantly owing to several factors, source of crude oil being one of them. Because of such inconsistency in composition, there are multiple gasoline fuel compositions with similar octane ratings. It is of interest to comparatively study such fuels with similar octane ratings and different composition, and thus dissimilar physical and chemical properties. Such an investigation is required to interpret differences in combustion behavior of gasoline fuels that show similar knock characteristics in a cooperative fuel research (CFR) engine, but may behave differently in direct injection spark ignition (DISI) engines or any other engine combustion modes.

Light naphtha is the light distillate from crude oil and can be used in compression ignition (CI) engines; its low boiling point and octane rating (RON = 64.5) enable adequate premixing. This study investigates the combustion characteristics of light naphtha (LN) and its multicomponent surrogate under various start of injection (SOI) conditions. LN and a five-component surrogate for LN, comprised of 43% n-pentane, 12% n-heptane, 10% 2-methylhexane, 25% iso-pentane and 10% cyclo-pentane, has been tested in a single cylinder optical diesel engine. The transition in combustion homogeneity from CI combustion to homogenized charge compression ignition (HCCI) combustion was then compared between LN and its surrogate. The engine experimental results showed good agreement in combustion phasing, ignition delay, start of combustion, in-cylinder pressure and rate of heat release between LN and its surrogate.

The effect of ethanol blended with three FACE (Fuels for Advanced Combustion Engines) gasolines, I, J and A corresponding to RON 70.3, 71.8 and 83.5, respectively, were compared to PRF70 and PRF84 with the same ethanol concentrations, these being 2%, 5%, 10%, 15% and 20% by volume. A Cooperative Fuel Research (CFR) engine was used to understand the blending effect of ethanol with FACE gasolines and PRFs in spark-ignited and homogeneous charge compression ignited mode. Blending octane numbers (BON) were obtained for both the modes. All the fuels were also tested in an ignition quality tester to obtain Blending Derived Cetane numbers (BDCN). It is shown that fuel composition and octane number are important characteristics of all the base fuels that have a significant impact on octane increase with ethanol. The dependency of octane number for the base fuel on the blending octane number depended on the combustion mode operated.