Search Results

Ford Motor Company’s assembly plants build vehicles in a certain sequence. The planned sequence for the plant’s trim and final assembly area is developed centrally and is sent to the plant several days in advance. In this work we present the study of two cases where the plant changes the planned sequence to cope with production constraints. In one case, a plant pulls ahead two-tone orders that require two passes through the paint shop. This is further complicated by presence in the body shop area of a unidirectional rotating tool that allows efficient build of a sequence “A-B-C” but heavily penalizes a sequence “C-B-A”. The plant changes the original planned sequence in the body shop area to the one that satisfies both pull-ahead and rotating tool requirements. In the other case, a plant runs on lean inventories. Material consumption is tightly controlled down to the hour to match with planned material deliveries.

Three computational gas and fluid dynamic methods, CV/UP (Control Volume/Uniform Pressure), CPM (Corpuscular Particle Method), and ALE (Arbitrary Lagrangian and Eulerian), were investigated in this research in an attempt to predict the responses of side crash pressure sensors. Acceleration-based crash sensors have been used extensively in the automotive industry to determine the restraint system firing time in the event of a vehicle crash. The prediction of acceleration-based crash pulses by using computer simulations has been very challenging due to the high frequency and noisy responses obtained from the sensors, especially those installed in crush zones. As a result, the sensor algorithm developments for acceleration-based sensors are largely based on prototype testing. With the latest advancement in the crash sensor technology, side crash pressure sensors have emerged recently and are gradually replacing acceleration-based sensor for side crash applications.

In recent years, the design of automotive components and assemblies have resulted in an over-reliance on advanced CAE tools especially the Finite Element Analysis. An emphasis on cost reduction and commonization of components in automotive industry has made it necessary to use the CAE tools in innovative ways. Use of FEA as a effective product development tool can be greatly enhanced if it provides a high degree of correlation with physical tests, thereby greatly limiting the investment in expensive prototypes and testing. This paper will discuss a robustness based methodology to realize effective correlation of finite element models with actual physical tests on automotive seat structure assembly, at a component, sub-system, and systems level. Based on a parameter design approach, the various factors that affect the degree of correlation between CAE models and physical tests will be described.

An eight-group taxonomy was created to classify real-world frontal crashes from the Crashworthiness Data System (CDS) component of the National Automotive Sampling System (NASS). Three steps were taken to develop the taxonomy: (1) frontal-impact towaway crashes were identified by examining 1985-2005 model year light passenger vehicles with Collision Deformation Classification (CDC) data from the 1995-2005 calendar years of NASS; (2) case reviews, engineering judgments, and categorization assessments were conducted on these data to produce the eight-group taxonomy; and (3) two subsets of the NASS dataset were analyzed to assess the consistency of the resulting taxonomic-group frequencies. “Full-engagement” and “Offset” crashes were the most frequent crash types, each contributing approximately 33% to the total. The group identified as “D, Y, Z No-Rail” was the most over-represented crash type for vehicles with at least one seriously-injured occupant.

It is generally accepted that all postures obtained from motion capture technology are realistic and accurate. Physical props are used to enable a subject to interact more realistically within a given virtual environment, yet, there is little data or guidance in the literature characterizing the use of such physical props in motion capture studies and how these effect the accuracy of postures captured. This study was designed to evaluate the effects of various levels of physical prop complexity on the motion-capture of a wide variety of automotive assembly tasks. Twenty-three subjects participated in the study, completing twelve common assembly tasks which were mocked up in a lab environment. There were 3 separate conditions of physical props: Crude, Buck, and Real. The Crude condition provided very basic props, or no props at all, while the Buck condition was a more elaborate attempt to provide detailed props. Lastly, the Real condition included real vehicle sections and real parts.

This study demonstrates the use of pressure sensing technology to predict the crash severity of frontal impacts. It presents an investigation of the pressure change in the front structural elements (bumper, crush cans, rails) during crash events. A series of subsystem tests were conducted in the laboratory that represent a typical frontal crash development series and provided empirical data to support the analysis of the concept. The pressure signal energy at different sensor mounting locations was studied and design concepts were developed for amplifying the pressure signal. In addition, a pressure signal processing methodology was developed that relies on the analysis of the air flow behavior by normalizing and integrating the pressure changes. The processed signal from the pressure sensor is combined with the restraint control module (RCM) signals to define the crash severity, discriminate between the frontal crash modes and deploy the required restraint devices.

Described in this paper is a component test methodology to evaluate the door trim armrest performance in an Insurance Institute for Highway Safety (IIHS) side impact test and to predict the SID-IIs abdomen injury metrics (rib deflection, deflection rate and V*C). The test methodology consisted of a sub-assembly of two SID-IIs abdomen ribs with spine box, mounted on a linear bearing and allowed to translate in the direction of impact. The spine box with the assembly of two abdominal ribs was rigidly attached to the sliding test fixture, and is stationary at the start of the test. The door trim armrest was mounted on the impactor, which was prescribed the door velocity profile obtained from full-vehicle test. The location and orientation of the armrest relative to the dummy abdomen ribs was maintained the same as in the full-vehicle test.

This paper describes the development of a three-dimensional lumped-mass structure and dummy model to study barrier-to-car side impacts. The test procedures utilized to develop model input data are also described. The model results are compared to crash test results from a series of six barrier-to-car crash tests. Sensitivity analysis using the validated model show the necessity to account for dynamic structural rate effects when using quasi-statically measured vehicle crush data.

This study deals with passenger side restraint system design for frontal impact and four impact modes are considered in optimization. The objective is to minimize the Relative Risk Score (RRS), defined by the National Highway Traffic Safety Administration (NTHSA)'s New Car Assessment Program (NCAP). At the same time, the design should satisfy various injury criteria including HIC, chest deflection/acceleration, neck tension/compression, etc., which ensures the vehicle meeting or exceeding all Federal Motor Vehicle Safety Standard (FMVSS) No. 208 requirements. The design variables include airbag firing time, airbag vent size, inflator power level, retractor force level. Some of the restraint feature options (e.g., some specific features on/off) are also considered as discrete design variables. Considering the local variability of input variables such as manufacturing tolerances, the robustness and reliability of nominal designs were also taken into account in optimization process.

Sunroof is placed in certain high-end vehicles to give user a better driving experience. All automakers are searching alternatives to reduce weight and cost in the vehicle, in which sunroofs are also impacted. Some alternatives are already applied, as a honeycomb paper used in some sunshades that presents benefits, as less weight and with a good cost reduction. Although, due the reduced weight for this part produced in this material, it shows more susceptibility to reproduce the vibration that vehicle propagates in movement, especially in bad condition roads. The sunroof assembly is dependent of the roof reinforcement and roof skin, but in this special case, the validation could be done in the components itself because the interaction of the sunshades is directly dependent of the other sunroof parts, as rails and front frame.

Optimization of heavy materials like steel, in order to create a lighter vehicle, it is a major goal among most automakers, since heavy vehicles simply cannot compete with a lightweight model's fuel economy. Thinking this way, this paper shows a case study where the Size Optimization technique is applied to a front floor reinforcement. The reinforcement is used by two different vehicles, a subcompact and a crossover Sport Utility Vehicle (SUV), increasing the problem complexity. The Size Optimization technique is supported by Finite Element Method (FEM) tools. FEM in Computer Aided Engineering (CAE) is a numerical method for solving engineering problems, and its use can help to optimize prototype utilization and physical testing.

Residual stress can affect directly the quality of products as result of manufacturing process, for example, the vehicular assembly of sheet metal parts, where the welding of thin plates is applied. One method that can prevent it is the use of CAE which helps to understand the mechanism of welding effects using finite element methods. Using this tool is possible to evaluate the impact of the welding process in order to reduce time and costs during the product development. It helps also to foresee future durability/customer usage problems during the product life.

Design for assembly (DFA) is a prominent strategy for manufacturing cost reduction in automotive industries. DFA in automotive component design is a complicated process since several competing targets have to be considered simultaneously in designing various functions and features. It requires specialized design knowledge as well as extensive quantitative analysis, comparison and evaluation. Analytical Hierarchic Process (AHP) is one of the tools that can assist such design and evaluation processes. It has been successfully applied in various processes when multiple competing goals and characteristics are involved. In this paper, we propose the application of AHP for DFA in automotive component design and present a case study involving car front end component design.

This paper presents some of the design rules used to calculate critical geometry of engine components, and the object-oriented component hierarchy system in PET. This paper also presents parametric solid model assembling schemes used to dynamically construct an assembly of whole powertrain systems. Some examples of powertrain concept design, such as the estimation of friction, packaging, and moving component clearances, will be presented. The computational efficiency of this concept design method will be compared to traditional methods also.

Headliner technology will be presented in this paper. Older established technologies such as cut & score, fiberglass, hardboard and resinated cotton are still used because of their proven reliability and low cost. But newer processes including polyester, natural fiber, Tramivex™ and urethane offer reliability, structure, acoustic performance and some recyclability. Fiberglass has always been a leader in acoustical performance but has breakage and handability issues in the assembly plants. This paper will be divided in four sections. The first section discusses manufacturing processes for headliners covering current and past. It also covers the materials used and types of facing. This section will state why headliner technology used in the USA is different than Europe or emerging markets. Second section describes acoustics. It will explain performance as related to material types. Porosity, cell type, fiber length and diameter is explained as it relates to the absorption of sound.

This paper describes the process of incorporation of 25% post-industrial recycled sheet molded composite (SMC) material in the 1998 Continental Hood inner. 1998 Continental Hood assembly consists of traditional SMC outer and this recycled hood inner along with three small steel reinforcements. BUDD Plastics collects SMC scraps from their manufacturing plants. The scrap is then processed and made into fillers for production of SMC. Strength of SMC comes from glass fibers and fillers are added to produce the final mix of raw materials. This recycled material is approximately 10% lighter and less stiff than the conventional virgin SMC. This presented unique challenges to the product development team to incorporate this material into a production vehicle in order to obtain the desired goal of reducing land fill and improving the environment.

In this study, the occupant containment characteristics of automotive laminated safety glass in side window applications was evaluated through two full-scale, full-vehicle dolly rollover crash tests. The dolly rollover crash tests were performed on sport utility vehicles equipped with heat-strengthened laminated safety glass in the side windows in order to: (1) evaluate the capacity of laminated side window safety glass to contain unrestrained occupants during rollover, (2) analyze the kinematics associated with unrestrained occupants during glazing interaction and ejection, and (3) to identify laminated side window safety glass failure modes. Dolly rollovers were performed on a 1998 Ford Expedition and a 2004 Volvo XC90 at a nominal speed of 43 mph, with unbelted Hybrid II Anthropomorphic Test Devices (ATDs) positioned in the outboard seating positions.

Control of drum brake squeal is difficult to accomplish. After many trials guided by CAE and previous experience, for a passenger car it was felt that changing the metallurgical characteristics of the drum would lead to improved noise performance. The chemistry of the drum casting material was altered. The carbon equivalent was modified by increasing carbon and silicon content of the castings as well as changing the other materials. The integral hub and drum assembly was tested on two different dynamometers. The results were also verified by finite element complex eigenvalue analysis. Finally the solution was validated through vehicle level testing - Los Angeles City Traffic (LACT). For the structural consideration rotary fatigue was evaluated by CAE comparison followed by test rig confirmation. The higher carbon equivalent material drums successfully eliminated the annoying squeal in customer vehicles.

A computational model of a mid-size sport utility vehicle was developed using MADYMO. The model includes a detailed description of the suspension system and tire characteristics that incorporated the Delft-Tyre magic formula description. The model was correlated by simulating a vehicle suspension kinematics and compliance test. The correlated model was then used to simulate a J-turn vehicle dynamics test maneuver, a roll and non-roll ditch test, corkscrew ramp and a lateral trip test, the results of which are presented in this paper. The results indicate that MADYMO is able to reasonably predict the vehicle and occupant responses in these types of applications and is potentially suited as a tool to help setup a suite of vehicle configurations and test conditions for rollover sensor testing. A suspension system sensitivity study is presented for the laterally tripped non-roll event.

An assessment tool was developed for rollover CAE signals evaluation to assess primarily the qualities of CAE generated sensor waveforms. This is a key tool to be used to assess CAE results as to whether they can be used for algorithm calibration and identify areas for further improvement of sensor. Currently, the method is developed using error estimates on mean, peak and standard deviation. More metrics, if necessary, can be added to the assessment tool in the future. This method has been applied to various simulated signals for laboratory-based rollover test modes with rigid-body-based MADYDO models.