Search Results

Well-mixed lean SI engine operation can provide improvements of the fuel economy relative to that of traditional well-mixed stoichiometric SI operation. This work examines the use of two methods for improving the stability of lean operation, namely multi-pulse transient plasma ignition and intake air preheating. These two methods are compared to standard SI operation using a conventional high-energy inductive ignition system without intake air preheating. E85 is the fuel chosen for this study. The multi-pulse transient plasma ignition system utilizes custom electronics to generate 10 kHz bursts of 10 ultra-short (12ns), high-amplitude pulses (200 A). These pulses were applied to a custom spark plug with a semi-open ignition cavity. High-speed imaging reveals that ignition in this cavity generates a turbulent jet-like early flame spread that speeds up the transition from ignition to the main combustion event.

It is well known that ultra-lean combustion can result in higher thermal efficiency, better fuel economy, and greatly reduced NOx emissions. Accomplishing ultra-lean combustion is very difficult with a conventional spark plug, and ignition instability can be cited as one of the factors. Therefore, it is thought that ignition system innovation is important for the achievement of ultra-lean combustion in gasoline engines. This study investigated high-speed plasma ignition as a new ignition system for internal combustion engines. High-speed plasma refers to the transient (non-equilibrated) phase of plasma before formation of an arc discharge; it is obtained by applying high voltage with an ultra-short pulse between coaxial cylindrical electrodes. High-speed plasma can inherently form a multi-channel discharge, with the electrical discharge spreading over a much larger volume than a spark discharge does.

The blade crossing event of a coaxial counter-rotating rotor is a potential source of noise and impulsive blade loads. Blade crossings occur many times during each rotor revolution. In previous research by the authors, this phenomenon was analyzed by simulating two airfoils passing each other at specified speeds and vertical separation distances, using the compressible Navier-Stokes solver OVERFLOW. The simulations explored mutual aerodynamic interactions associated with thickness, circulation, and compressibility effects. Results revealed the complex nature of the aerodynamic impulses generated by upper/lower airfoil interactions. In this paper, the coaxial rotor system is simulated using two trains of airfoils, vertically offset, and traveling in opposite directions. The simulation represents multiple blade crossings in a rotor revolution by specifying horizontal distances between each airfoil in the train based on the circumferential distance between blade tips.

NASA is developing a novel waste bag concept for filling, storing and drying astronaut fecal material. The three-layer bag is lined with a membrane that is impermeable to solid and liquid matter but permeable to gases. The air flow provided by a blower assists in containing the waste in the bag. After use, the bag is sealed and then connected to a vacuum manifold for drying the waste. This paper describes the development of theoretical models for analyzing the air flow patterns in the bag during the filling process as well as the parameters governing the drying rate. The models will be used to support the design and testing of the waste bag.

This study introduces several new concepts for suited EVA astronaut ingress/egress (departure and return) from a pressurized planetary surface habitat, based on use of a rear-entry suit and a suit lock or suitport. We provide insight into key operational aspects and integration issues, as well as the results of a requirements analysis and risk assessment of the concepts. The risk assessment included hazard analysis, hazard mitigation techniques, failure mode assessment, and operational risk assessment. Also included are performance and mass estimates for the egress concepts, and concepts for integration of the egress concepts with potential planetary habitat designs.

In February 2004 NASA released “The Vision for Space Exploration.” The important goals outlined in this document include extending human presence in the solar system culminating in the exploration of Mars. Unprocessed waste poses a biological hazard to crew health and morale. The waste processing methods currently under consideration include incineration, microbial oxidation, pyrolysis and compaction. Although each has advantages, no single method has yet been developed that is safe, recovers valuable resources including oxygen and water, and has low energy and space requirements. Thus, the objective of this project is to develop a low temperature oxidation process to convert waste cleanly and rapidly to carbon dioxide and water. In the Phase I project, TDA Research, Inc. demonstrated the potential of a low temperature oxidation process using ozone. In the current Phase II project, TDA and NASA Ames Research Center are developing a pilot scale low temperature ozone oxidation system.

The present study aims to document the drag reduction for a two-vehicle platoon by operating two full-scale Ford Windstar vans in tandem on a desert lakebed. Drag forces are measured with the aid of a special tow bar force measuring system designed and manufactured at USC. The testing procedure consists of a smooth acceleration, followed by a smooth deceleration of the platoon. Data collected during acceleration allows the calculation of the drag force on the trail-vehicle, while data collected during deceleration is used to calculate the drag on the lead vehicle. Results from the full-scale tests show that the drag behaviors for the two vans are in general agreement with the earlier conclusions drawn from the wind tunnel testsænamely, both vans experience substantial drag savings at spacings of a fraction of a car length.

The development of surrogate mixtures that represent gasoline combustion behavior is reviewed. Combustion chemistry behavioral targets that a surrogate should accurately reproduce, particularly for emulating homogeneous charge compression ignition (HCCI) operation, are carefully identified. Both short and long term research needs to support development of more robust surrogate fuel compositions are described. Candidate component species are identified and the status of present chemical kinetic models for these components and their interactions are discussed. Recommendations are made for the initial components to be included in gasoline surrogates for near term development. Components that can be added to refine predictions and to include additional behavioral targets are identified as well. Thermodynamic, thermochemical and transport properties that require further investigation are discussed.

An innovative design that meets both Shuttle and Space Station requirements for a user-friendly, volume-efficient, portable glovebox system has been developed at Ames Research Center (ARC). The Standard Interface Glovebox (SIGB) has been designed as a two Middeck locker-sized system that mounts in a Middeck Rack Structure (MRS) or in any rack using the Standard Interface Rack (SIR) rail spacing. The MRS provides structural support for the SIGB during all aspects of the mission and is an interface consistent with NASA's desire for commonality of mechanical interfaces, allowing the SIGB to be flown on essentially any manned space platform. The SIGB provides an enclosed work volume which operates at negative pressure relative to ambient, as well as excellent lighting and ample work volume for anticipated life sciences-related experiment operations inflight.

PGBA, a plant growth facility developed for commercial space biotechnology research, successfully grew a total of 50 plants (6 species) during 10 days aboard the Space Shuttle Endeavor (STS-77), and has reflown aboard the Space Shuttle Columbia (STS-83 for 4 days and STS-94 for 16 days) with 55 plants and 10 species. The PGBA life support system provides atmospheric, thermal, and humidity control as well as lighting and nutrient supply in a 33 liter microgravity plant growth chamber. The atmosphere treatment system removes ethylene and other hydrocarbons, actively controls CO2 replenishment, and provides passive O2 control. Temperature and humidity are actively controlled.

A steady-state system mass balance calculation was performed to investigate design issues regarding the storage and/or processing of solid waste. In the initial stages of BIO-Plex, only a certain percentage of the food requirement will be satisfied through crop growth. Since some food will be supplied to the system, an equivalent amount of waste will accumulate somewhere in the system. It is a system design choice as to where the mass should accumulate in the system. Here we consider two approaches. One is to let solid waste accumulate in order to reduce the amount of material processing that is needed. The second is to process all of the solid waste to reduce solid waste storage and then either resupply oxygen or add physical/chemical (P/C) processors to recover oxygen from the excess carbon dioxide and water that is produced by the solid waste processor.

The Plant Generic BioProcessing Apparatus (PGBA), a plant growth facility developed for commercial space biotechnology research, has flown successfully on 3 spaceflight missions for 4, 10 and 16 days. The environmental control systems of this plant growth chamber (28 liter/0.075 m2) provide atmospheric, thermal, and humidity control, as well as lighting and nutrient supply. Typical performance profiles of water transpiration and dehumidification, carbon dioxide absorption (photosynthesis) and respiration rates in the PGBA unit (on orbit and ground) are presented. Data were collected on single and mixed crops. Design options and considerations for the different sub-systems are compared with those of similar hardware.

The “low power-CO2 removal (LPCOR) system” is an advanced air revitalization system that is under development at NASA Ames Research Center. The LPCOR utilizes the fundamental design features of the ‘four bed molecular sieve’ (4BMS) CO2 removal technology of the International Space Station (ISS). LPCOR improves power efficiency by replacing the desiccant beds of the 4BMS with a membrane dryer and a state-of-the-art, structured adsorbent device that collectively require 25% of the thermal energy required by the 4BMS desiccant beds for regeneration. Compared to the 4BMS technology, it has the added functionality to deliver pure, compressed CO2 for oxygen recovery. The CO2 removal and recovery functions are performed in a two-stage adsorption compressor. CO2 is removed from the cabin air and partially compressed in the first stage. The second stage performs further compression and delivers the compressed CO2 to a reduction unit such as a Sabatier reactor for oxygen recovery.

Designers of future space vehicles envision simplifying the Atmosphere Revitalization (AR) system by combining the functions of trace contaminant (TC) control and carbon dioxide removal into one swing-bed system. Flow rates and bed sizes of the TC and CO2 systems have historically been very different. There is uncertainty about the ability of trace contaminant sorbents to adsorb adequately in a high-flow or short bed length configurations, and to desorb adequately during short vacuum exposures. This paper describes preliminary results of a comparative experimental investigation into adsorbents for trace contaminant control. Ammonia sorbents and low temperature catalysts for CO oxidation are the foci. The data will be useful to designers of AR systems for Constellation. Plans for extended and repeated vacuum exposure of ammonia sorbents are also presented.

Dynamic simulation of the lunar outpost habitat life support was undertaken to investigate the impact of life support failures and to investigate possible responses. Some preparatory static analysis for the Lunar Outpost life support model, an earlier version of the model, and an investigation into the impact of Extravehicular Activity (EVA) were reported previously. (Jones, 2008-01-2184, 2008-01-2017) The earlier model was modified to include possible resupply delays, power failures, recycling system failures, and atmosphere and other material storage failures. Most failures impact the lunar outpost water balance and can be mitigated by reducing water usage. Food solids and nitrogen can be obtained only by resupply from Earth. The most time urgent failure is a loss of carbon dioxide removal capability. Life support failures might be survivable if effective operational solutions are provided in the system design.

Two separate experimental rigs used in tests on NASA and Zero-G Corporation aircrafts flying low-gravity trajectories, and in the NASA 2.2 Second Drop Tower have been developed to test the functioning of the Flexible Membrane Commode (FMC) concept under reduced gravity conditions. The first rig incorporates the flexible, optically opaque membrane bag and the second rig incorporates a transparent chamber with a funnel assembly for evacuation that approximates the size of the membrane bag. Different waste dispensers have been used including a caulking gun and flexible hose assembly, and an injection syringe. Waste separation mechanisms include a pair of wire cutters, an iris mechanism, as well as discrete slug injection. The experimental work is described in a companion paper. This paper focuses on the obtained results and analysis of the data.

In February 2004 NASA released “The Vision for Space Exploration.” The goals outlined in this document include extending the human presence in the solar system, culminating in the exploration of Mars. A key requirement for this effort is to identify a safe and effective method to process waste. Methods currently under consideration include incineration, microbial oxidation, pyrolysis, drying, and compaction. Although each has advantages, no single method has yet been developed that is safe, recovers valuable resources including oxygen and water, and has low energy and space requirements. Thus, the objective of this work was to develop a low temperature oxidation process to convert waste cleanly and rapidly to carbon dioxide and water. TDA and NASA Ames Research Center have developed a pilot scale low temperature ozone oxidation system to convert organic waste to CO2 and H2O.

Aviation training has remained largely untouched by decades of development in cognitive science. In aviation, people must be trained to perform complicated tasks and make good operational decisions in complex dynamic environments. However, traditional approaches to professional aviation training are not well designed to accomplish this goal. Aviation training has been based mainly on relatively rigid classroom teaching of factual information followed by on-the-job mentoring. This approach tends to compartmentalize knowledge. It is not optimal for teaching operational decision-making, and it is costly in time and personnel. The effectiveness of training can be enhanced by designing programs that support the psychological processes involved in learning, retention, retrieval, and application. By building programs that are informed by current work in cognitive science and that utilize modern technological advances, efficient training programs can be created.

We demonstrate the interaction of two truck shapes in tandem. Both trucks experience a decreased drag coefficient from the interaction. The degree of drag saving depends strongly upon the drag coefficients of the model trucks in isolation, and upon how the two trucks are arranged. For the two simplest shapes-parallelepipeds with or without partial leading-edge rounding-the total drag saving can range from 10 percent to 40% at a spacing of 2√A (approximately 18 feet at full scale) depending upon whether the lead or the trail parallelepiped has rounding. These two shapes-blunt and rounded-have drag coefficients in isolation of 0.94 and 0.51 respectively, and probably bracket the savings to be obtained for all real truck geometries. Our realistic model trucks (with wheels and a gap between tractor and trailer serving to distribute the source of drag along the length of the truck) have drag coefficients in the range CD = 0.5-0.7, and the total drag saving is a more modest 15-20% at 2√A.

The results reported are from tests on July 6-8, 1999, on a limited-access 12km section of I -15 in San Diego. The tests involved 2, 3 and 4-car platoons operated and maintained by PATH personnel under the auspices of CALTRANS and utilized Buick LeSabre sedans under fully automatic longitudinal and lateral control. Multiple sensor data was acquired, including the fuel injector pulse width. We demonstrate that the fuel injector pulse width, in combination with engine RPM and forward speed, can be used to determine accurate estimates of instantaneous fuel consumption. The repeatability for total fuel consumed over a 2.4 km portion of the test path is ±1% based upon multiple single car runs over the three day period, with the major portion of the uncertainty arising from changing wind conditions. Fuel savings for individual vehicles vary from 0-10% depending upon number of vehicles, vehicle spacing, and vehicle position within the platoon.