Search Results

This study reports gaseous and particle (ultrafine and black carbon (BC)) emissions from a turbofan engine core on standard Jet A-1 and three alternative fuels, including 100% hydrothermolysis synthetic kerosene with aromatics (CH-SKA), 50% Hydro-processed Esters and Fatty Acid paraffinic kerosene (HEFA-SPK), and 100% Fischer Tropsch (FT-SPK). Gaseous emissions from this engine for various fuels were similar but significant differences in particle emissions were observed. During the idle condition, it was observed that the non-refractory mass fraction in the emitted particles were higher than during higher engine load condition. This observation is consistent for all test fuels. The 100% CH-SKA fuel was found to have noticeable reductions in BC emissions when compared to Jet A-1 by 28-38% by different BC instruments (and 7% in refractory particle number (PN) emissions) at take-off condition.

The Flight Research Laboratory (FRL), National Research Council (NRC) of Canada is currently developing an in-flight aircraft aerodynamic model identification technique that determines the small perturbation model at a given test condition. Initial demonstrations have been carried out using the NRC Falcon 20 research aircraft. An efficient system architecture, in terms of both software algorithms and hardware processing, has been designed to meet the stringent near real-time requirements of an in-flight system. As well, novel hardware and software techniques are being applied to the calibration and measurement of the fundamental in-flight parameters, such as air data. The small perturbation models are then combined to develop a global model of the aircraft that is validated by comparing the model response to flight data. The maneuvers were performed according to the FAA Acceptance Test Guide (ATG).

A joint program between Bell Helicopter Textron Canada and the Flight Research Laboratory of Canada's National Research Council was initiated to address the aerodynamic modelling challenges of the Bell M427 helicopter. The primary objective was to use the NRC parameter estimation technique, based on modified maximum likelihood estimation (MMLE), on a limited set of flight test data to efficiently develop an accurate forward-flight mathematical model of the Bell M427. The effect of main rotor design changes on the aircraft stability characteristics was also investigated, using parameter estimation. This program has demonstrated the feasibility of creating a forward-flight rotorcraft aerodynamic mathematical model based on time-domain parameter estimation, and the ability of a 6 degree-of-freedom MMLE model to accurately document the impact of minor rotor modifications on aircraft stability.

The noise generated by the flow of air past a transport truck is a key design factor for the manufacturers of these vehicles as the sound levels in the cabin are a significant component of driver comfort. This paper describes a collaboration between Volvo GTT and the National Research Council Canada to measure the in-cabin aeroacoustics of a full-scale cab-over tractor in the NRC 9 m Wind Tunnel. Acoustic instrumentation was installed inside the tractor to record cabin noise levels and externally to acquire tunnel background noise data. Using a microphone mounted on the driver’s-side tunnel wall as a reference to remove variations in background noise levels between data points, differences in cabin noise levels were able to be detected when comparing the tractor with different configurations. The good repeatability of the data allowed for differences of as little as 0.5 dB to be measured.

Data is presented from a number of flight research aircraft, which have been involved in the research of the effects of inflight icing, in a variety of atmospheric supercooled droplet and mixed-phase icing environmental conditions. The aircraft Types considered cover both Pneumatic and Thermal Ice Protection Systems (IPS). Icing includes supercooled droplet impact icing upon airframe and propeller blades and cold-soaked frost icing. The drag effects of inflight icing, from mixed-phase small and large droplets encountered during the course of SALPEX cloud physics research operations, upon a Fokker F-27 turboprop transport aircraft, have been analyzed. Furthermore, during the course of AIRS 1.5 and AIRS II inflight icing flight research operations, the NRC Convair conducted aerodynamic characterization maneuvers, following and during icing accretion in a wide range of environmental conditions of altitude, air temperature, LWC and droplet spectra.

This paper describes the commissioning of a linear compressor cascade rig for ice crystal research. The rig is located in an altitude chamber so the test section stagnation pressure, temperature and Mach number can be varied independently. The facility is open-circuit which eliminates the possibility of recirculating ice crystals reentering the test section and modifying the median mass diameter and total water content in time. As this is an innovative facility, the operating procedures and instrumentation used are discussed. Sample flow quality data are presented showing the distribution of velocity, temperature, turbulence intensity and ice water concentration in the test section. The control and repeatability of experimental parameters is also discussed.

Gaseous and particle emission assessments on a 1.15 kN-thrust turbojet engine were conducted at five altitudes in an altitude chamber with Jet A-1 fuel, pure Fischer Tropsch (FT), and two mixed fuels of JP-8 with FT or Camelina-based hydro-processed jet fuels. In general, lower emissions in CO₂, NOx, and particle number as well as higher emissions in CO and THC were observed at higher altitudes compared to lower altitudes. These observations, which were similar for all test fuels, were attributed to the reduced combustion efficiency and temperature at higher altitudes. The use of alternative fuels resulted in lower CO₂ emissions, ranging from 0.7% to 1.7% for 50% to 100% synthetic fuel in the fuel mixture at various altitudes. In terms of CO, the use of 100% FT fuel resulted in CO reduction up to 9.7% at 1525 m altitude and up to 5.9% at 9145 m altitude.

Adoption of hydro-processed esters and fatty acid biojet fuels is a critical component for the sustainability of the aviation industry. Aviation biofuels reduce pollution and provide alternatives to conventional fossil fuels. A study of the impacts of biofuels on emissions from a T56 turbo-prop engine was undertaken as a joint effort among several departments of the Government of Canada. In this study, particulate (including particle number and black carbon (BC) mass) and regulated gaseous emissions (CO2, CO, NO, NO2, THC) were characterized with the engine operating on conventional F-34 jet fuel and jet fuel blended with camelina-based hydro-processed biojet fuel (C-HEFA) by 50% in volume. Emissions characterization, conducted after 20-hour ground engine durability tests, showed immediate significant reductions in particle number and BC mass when the engine was operated on the C-HEFA blend.

In 2021 the Federal Aviation Administration in collaboration with the National Research Council of Canada performed research on altitude ice crystal icing of aircraft engines using the modular compressor rig, ICE-MACR, in an altitude wind tunnel. The aim of the research campaign was to address research needs related to ice crystal icing of aircraft engines outlined in FAA publication Engine Ice Crystal Icing Technology Plan with Research Needs. This paper reports the findings on ice accretion from a configuration of ICE-MACR with two compression stages. Inherent in two-stage operation is not just additional fracturing and heating by the second stage but also higher axial velocity and potentially greater centrifuging of particles. These factors influence the accretion behavior in the test article compared to single stage accretion.

Future compliance to FAA 14 CFR Part 25 and EASA CS-25 Appendix O conditions has required icing wind tunnels to expand their cloud simulation envelope, and demonstrate accurate calibration of liquid water content and droplet particle size distributions under these conditions. This has led to a renewed community interest in the accuracy of these calibrations, and the potential inter-facility bias due to the choice of instrumentation and processing methods. This article provides a comparison of the response of various hot-wire liquid water content instruments under Appendix C and supercooled large droplet conditions, after an independent similar analysis at other wind tunnel facilities. The instruments are being used, or are under consideration for use, by facilities collaborating in the ICE GENESIS program.

The National Research Council of Canada (NRC) has undergone the development of a Small Axial Compressor Rig for modelling altitude ice accretion in aircraft engines. The rig consists of two axial compressor stages measuring approximately 150mm in diameter, an extension duct to allow residence time for partial melting of ice crystals and a test piece. The axial compressor stages are intended to provide realistic engine conditioning such as fracture, pressure rise, temperature rise and centrifuging of glaciated ice crystals entering the rig. The rig was designed for use in altitude icing wind tunnels such as the NRC’s altitude icing wind tunnel (AIWT), research altitude test facility (RATFac.), and those of other organization such as NASA Glenn and Technical University of Braunshweig. Previous development work [1] provided partial validation of the aerodynamic performance of just the first compressor stage at 90% power.

The National Research Council Canada has collected a large number of corroded and non-corroded fuselage lap joints from retired and operational aircraft. A number of these corroded joints have been disassembled in order to quantify the level of corrosion. During the disassembly, it was often observed that common repair techniques resulted in damage to the structure. The damage observed was significant enough to raise concerns regarding the effect of the repair techniques on structural integrity. This paper describes the different types of damage found.

This paper describes the equipment, analysis methods and results obtained for particle size measurements based on a particle imaging velocimetry (PIV) system in which a short duration laser pulse is used to backlight airborne particles. This produces high quality and high resolution images of fast moving airborne particles in a non-intrusive manner. This imaging technique is also used to examine particle morphology and 2D particle trajectory and velocity. The image analysis methods are outlined and validation test results discussed which show the measurement of reference glass beads between 20 and 400 microns were generally to within their stated size. As well, validation testing using known icing wind tunnel droplet distributions were compared with Spraytek 2000 Malvern droplet size measurements and showed agreement of the MVD's to be within ±5% for distributions having nominally 20, 40 and 80 micron MVD's.

Simulations of supercooled large droplet (SLD) icing environments within the NRC's Altitude Icing Wind Tunnel (AIWT) have been performed in which broad band mass distribution spectra are achieved that include a distinct pattern of liquid water content (LWC) over a range of droplet sizes (i.e., bi-modal distribution). The mass distribution is achieved through modification of the existing spray system of the AIWT to allow two spray profiles with differing LWC and median volumetric diameter (MVD) to be simultaneously injected into the flow. Results of spray profile distributions measured in the test section have demonstrated that freezing drizzle conditions, where MVD is either less than or greater than 40 μm, can be achieved.

Under contract to Airlines for America (A4A), APS Aviation Inc. (APS), in collaboration with the National Research Council of Canada (NRC), completed an aircraft ground icing exploratory research project at the NRC 3 m × 6 m Wind Tunnel in Ottawa in January 2019. The purpose of this project was to investigate the feasibility of using aerodynamic data to evaluate the performance of contaminated anti-icing fluid, rather than the traditional visual fluid failure indicators that are used to develop Holdover Times (HOTs). The aerodynamic performance of a supercritical airfoil model with anti-icing fluids and snow contamination was evaluated against the clean, dry performance of the airfoil in order to calculate the associated aerodynamic penalty. The visual failure of the fluid was also evaluated for each run, and the visual and aerodynamic results were compared against each other for each contamination exposure time.

High altitude ice crystals are causing in-service events in excess of one per month for commercial aircraft. The effects include air data probes malfunctioning (pitot pressure and total air temperature in particular), and uncommanded engine power loss or flameout events. The National Research Council Canada (NRC) has developed a particle detection probe (PDP) that mounts on the fuselage of aircraft to sense and quantify the ice crystals in the environment. The probe is low-power and non-intrusive. This paper presents the results of ground and flight testing of this probe. Results are presented for ground testing in a sea level ice crystal wind tunnel and an altitude icing tunnel capable of generating both ice crystal and super-cooled liquid. The PDP was operated on several flight campaigns and the results of two will be presented.

Ice crystals ingested by a jet engine at high altitude can partially melt and then accrete within the forward stages of the compressor, potentially causing performance loss, damage and/or flameout. Recent research into this ice crystal icing (ICI) phenomenon conducted at the National Research Council of Canada suggests that the liquid water content vliq of an accretion significantly affects the accretion's susceptibility to erosion by ice crystals, and therefore accretion growth. This paper describes the development and application of an instrument for measuring vliq, potentially providing a method for correlating erosion behavior (e.g. as ductile or brittle) and properties. The instrument measures the complex admittance Y* of a mixed-phase deposit bridging a pair of electrodes, which is modeled as a resistor and capacitor in parallel, and calculates the deposit's relative permittivity εr from the capacitance.

Ice crystals ingested by a jet engine at high altitude can partially melt and then accrete within the compressor, potentially causing performance loss, damage and/or flameout. Several studies of this ice crystal icing (ICI) phenomenon conducted in the RATFac (Research Altitude Test Facility) altitude chamber at the National Research Council of Canada (NRCC) have shown that liquid water is required for accretion. CFD-based tools for ICI must therefore be capable of predicting particle melting due to heat transfer from the air warmed by compression and possibly also due to impact with warm surfaces. This paper describes CFD simulations of particle melting and evaporation in the RATFac icing tunnel for the former mechanism, conducted using a Lagrangian particle tracking model combined with a stochastic random walk approach to simulate turbulent dispersion. Inter-phase coupling of heat and mass transfer is achieved with the particle source-in-cell method.

The National Research Council’s Gas Turbine Laboratory provides industry leading icing facilities that allow manufacturers to develop, validate and certify new products for flight in adverse conditions. This paper shows how NRC measurement techniques are used across the facilities, and presents a literature-review of recently developed capabilities. The overview includes new details on some facilities, and future capabilities that are in development or planned for the near future. Methods developed at the NRC for characterizing inclement conditions are discussed and include the Isokinetic Probe, Particle Shadow Velocimetry, the Particle Detection Probe, and a size-binned real-time thermodynamic evaporation model.

The SAE G-27 committee was tasked by ICAO to develop a performance-based packaging standard for lithium batteries transported as cargo on aircraft. The standard details test criteria to qualify packages of lithium batteries & cells for transportation as cargo on-board passenger aircraft. Lithium batteries and cells have been prohibited from shipment as cargo on passenger aircraft since 2016. This paper summarizes the results of the tests conducted by Transport Canada and National Research Council Canada to support the development of this standard with evidence-based recommendations. It includes a description of the test specimens, the test set up, instrumentation used, and test procedures following the standard as drafted to date. The study considered several lithium-ion battery and cell chemistries that were tested under various proposed testing scenarios in the draft standard.