Search Results

The introduction of alternative fuels is crucial to limit greenhouse gases. CNG is regarded as one of the most promising clean fuels given its worldwide availability, its low price and its intrinsic properties (high knocking resistance, low carbon content...). One way to optimize dedicated natural gas engines is to improve the CNG slow burning velocity compared to gasoline fuel and allow lean burn combustion mode. Besides optimization of the combustion chamber design, hydrogen addition to CNG is a promising solution to boost the combustion thanks to its fast burning rate, its wide flammability limits and its low quenching gap. This paper presents an investigation of different methane/hydrogen blends between 0% and 40 vol. % hydrogen ratio for three different combustion modes: stoichiometric, lean-burn and stoichiometric with EGR.

The paper discusses the concept, specification and performance of a new, dedicated range extender engine for plug-in series hybrid vehicles conceived and designed by Lotus Engineering. This has been undertaken as part of a consortium project called Limo Green, part-funded by the UK government. The Lotus Range Extender engine has been conceived from the outset specifically as an engine for a plug-in series hybrid vehicle, therefore being free of some of the constraints placed on engines which have to mate to conventional, stepped mechanical transmissions. The paper starts by defining the philosophical difference between an engine for range extension and an engine for a full series hybrid vehicle, a distinction which is important with regard to how much power each type must produce. As part of this, the advantages of the sparkignition engine over the diesel are outlined.

In order to address the CO₂ emissions issue and to diversify the energy for transportation, CNG (Compressed Natural Gas) is considered as one of the most promising alternative fuels given its high octane number. However, gaseous injection decreases volumetric efficiency, impacting directly the maximal torque through a reduction of the cylinder fill-up. To overcome this drawback, both independent natural gas and gasoline indirect injection systems with dedicated engine control were fitted on a RENAULT 2.0L turbocharged SI (Spark Ignition) engine and were adapted for simultaneous operation. The main objective of this innovative combination of gas and liquid fuel injections is to increase the volumetric efficiency without losing the high knocking resistance of methane.

Partially Premixed Combustion (PPC) of fuels in the gasoline octane range has proven its potential to achieve simultaneous reduction in soot and NOX emissions, combined with high indicated efficiencies; while still retaining proper control over combustion phasing with the injection event, contrary to fully premixed strategies. However, gasoline fuels with high octane number as the commonly available for the public provide a challenge to ensure reliable ignition especially in the low load range, while fuel blends with lower octane numbers present problems for extending the ignition delay in the high load range and avoid the onset of knocking-like combustion. Thus, choosing an appropriate fuel and injection strategy is critical to solve these issues, assuring successful PPC operation in the full engine map.

The tumble flow in modern spark ignition engines is assuming an evermore important role for fuel guiding, air/fuel mixing and the generation of turbulence kinetic energy to enhance the combustion process. This paper describes results obtained with laser Doppler anemometry in multiple vertical planes in the cylinder of a motored, tumble flow engine and looks at the post processed data in terms of tumble ratios and mean and turbulence kinetic energies. The tumble results indicate very different flow fields in parallel planes lying in the main tumble direction, showing the complex nature of the flows in the cylinder. A simple method of integrating the tumble ratios from the different planes is suggested, leading to a tumble ratio more in line with those expected from an integrated method of measuring tumble, albeit these results are crank angle dependent. The tumble in a perpendicular plane shows unexpected asymmetries and values for the tumble.

Reducing NOx tailpipe emissions is one of the major challenges when developing automotive Diesel engines which must simultaneously face stricter emission norms and reduce their fuel consumption/CO2 emission. In fact, the engine control system has to manage at the same time the multiple advanced combustion technologies such as high EGR rates, new injection strategies, complex after-treatment devices and sophisticated turbocharging systems implemented in recent diesel engines. In order to limit both the cost and duration of engine control system development, a virtual engine simulator has been developed in the last few years. The platform of this simulator is based on a 0D/1D approach, chosen for its low computational time. The existing simulation tools lead to satisfactory results concerning the combustion phase as well as the air supply system. In this context, the current paper describes the development of a new NOx emission model which is coupled with the combustion model.

Fuel consumption in internal combustion engines and their associated CO2 emissions have become one of the major issues facing car manufacturers everyday for various reasons: the Kyoto protocol, the upcoming European regulation concerning CO2 emissions requiring emissions of less than 130g CO2/km before 2012, and customer demand. One of the most efficient solutions to reduce fuel consumption is to downsize the engine and increase its specific power and torque by using turbochargers. The engine and the turbocharger have to be chosen carefully and be finely tuned. It is essential to understand and characterise the turbocharger's behaviour precisely and on its whole operating range, especially at low engine speeds. The characteristics at low speed are not provided by manufacturers of turbochargers because compressor maps cannot be achieve on usual test bench.

Lean NOx trap (LNT) and Selective Catalytic Reduction catalysts (SCR) are two leading candidates for diesel NOx after-treatment. Each technology exhibits good properties to reduce efficiently diesel NOx emissions in order to match the forthcoming EURO 6 standards. NOx reduction in LNT is made through a two-step process. In normal (lean) mode, diesel engine exhausts NOx is stored into the NOx trap; then when necessary the engine runs rich during limited time to treat the stored NOx. This operating mode has the benefit of using onboard fuel as NOx reducer. But NOx trap solution is restrained by limited active temperature windows. On the other hand, NH₃-SCR catalysts operate in a wider range of temperature and do not contain precious metals. However, NH₃-SCR systems traditionally use urea-water solution as reducing agent, requiring thus additional infrastructure to supply the vehicles with enough reducer. These pros and cons are quite restrictive in classical LNT or NH₃-SCR architecture.

To improve the prediction of the combustion processes in spark ignition engines, a 0D flame/wall interaction submodel has been developed. A two-zones combustion model is implemented and the designed submodel for the flame/wall interaction is included. The flame/wall interaction phenomenon is conceived as a dimensionless function multiplying the burning rate equation. The submodel considers the cylinder shape and the flame surface that spreads inside the combustion chamber. The designed function represents the influence of the cylinder walls while the flame surface propagates across the cylinder. To determine the validity of the combustion model and the flame/wall interaction submodel, the system was tested using the available measurements on a 2 liter SI engine. The model was validated by comparing simulated cylinder pressure and energy release rate with measurements. A good agreement between the implemented model and the measurements was obtained.

High engine efficiency and low emissions on spark ignition engines can be achieved with a new camshaft profile switching device. This enables the use of two camshaft profiles for inlet and exhaust that can be switched independent of each other by any engine management input. This paper proposes the use of this device to give an excellent torque curve together with reduced emissions, by selecting from two discrete inlet and exhaust camshaft profiles and timings against engine parameters such as speed, load and temperature.

Iso-stoichiometric ternary blends - in which three-component blends of gasoline, ethanol and methanol are configured to the same stoichiometric air-fuel ratio as an equivalent binary ethanol-gasoline blend - can function as invisible "drop-in" fuels suitable for the existing E85/gasoline flex-fuel vehicle fleet. This has been demonstrated for the two principal means of detecting alcohol content in such vehicles, which are considered to be a virtual, or software-based, sensor, and a physical sensor in the fuel line. Furthermore when using such fuels the tailpipe CO₂ emissions are essentially identical to those found when the vehicle is operated on E85. Because of the fact that methanol can be made from a wider range of feed stocks than ethanol and at a cheaper price, these blends then provide opportunities to improve energy security, to reduce greenhouse gas emissions and to produce a fuel blend which could potentially be cheaper on a cost-per-unit-energy basis than gasoline or diesel.

Impact noise, inside a car, due to tire-launched gravel on the road can lead to loss of quality perception. Gravel noise is mainly caused by small-sized particles which are too small to be seen on the road by the driver. The investigation focuses on the identification of the mechanisms of excitation and transfer. The spatial distribution of the particles flying from a tire is determined, as well as the probable impact locations on the vehicle body-panels. Finally the relative noise contributions of the body-panels are estimated by adding the panel-to-ear transfer functions. This form of Transfer-Path-Analysis allows vehicle optimization and target setting on the level of the tires, exterior panel treatment and isolation.

Biofuels are a renewable energy source. When used as extenders for transportation fuels, biofuels contribute to the global reduction of Green House Gas and CO2 emissions from the transport sector and to security and independence of energy supply. On a “Well to Wheel” basis they are much more CO2 efficient than conventional fossil fuels. All vehicles currently in circulation in Europe are capable of using 5 % biodiesel. The introduction of higher percentages biodiesel needs new specific standards and vehicle tests validation. The development of vehicles compatible with 30% biodiesel blends in diesel fuel includes the validation of each part of both engine and fuel vehicle systems to guarantee normal operation for the entire life of the vehicle.

The engine of a high performance sports car has been converted to operation on E85, a high alcohol-blend fuel containing nominally 85% ethanol and 15% gasoline by volume. In addition to improving performance, the conversion resulted in significant improvement in full-load thermal efficiency versus operation on gasoline. This engine has been fitted in a test vehicle and made flex-fuel capable, a process which resulted in significant improvements in both vehicle performance and tailpipe CO2 when operating solely on ethanol blends, offering an environmentally-friendly approach to high performance motoring. The present paper describes some of the highlights of the development of the flex-fuel calibration to enable the demonstrator vehicle to operate on any mixture of 95 RON gasoline and E85 in the fuel tank. It also discusses how through detailed development, the vehicle has been made to comply with primary pollutant emissions legislation on any ethanol-gasoline mixture up to E85.

The future exploitation of global energy resources is currently being hotly debated by politicians and by sections of the scientific community but there is little guidance available in the engineering literature as to the full gamut of options or their viability with respect to fuelling the world's vehicles. In the automotive industry extensive research is being undertaken on the use of alternative fuels in internal combustion engines and on the development of alternative powerplants but often the long-term strategy and sustainability of the energy sources to produce these fuels is not clearly enunciated. The requirement to reduce CO2 emissions in the face of accelerating global warming scenarios and the depletion of fossil-fuel resources has led to the widespread assumption that some form of ‘hydrogen economy’ will prevail; this view is seldom justified or challenged.

The paper discusses the use of alcohol fuels in high performance pressure-charged engines such as are typical of the type being developed under the ‘downsizing’ banner. To illustrate this it reports modifications to a supercharged high-speed sports car engine to run on an ethanol-based fuel (ethanol containing 15% gasoline by volume, or ‘E85’). The ability for engines to be able to run on alcohol fuels may become very important in the future from both a global warming viewpoint and that of security of energy supply. Additionally, low-carbon-number alcohol fuels such as ethanol and methanol are attractive alternative fuels because, unlike gaseous fuels, they can be stored relatively easily and the amount of energy that can be contained in the vehicle fuel tank is relatively high (although still less than when using gasoline).

An ongoing program has made further technology advances in onboard fuel processors for use with PEM fuel cells. These systems are being explored as an option for reducing vehicle CO2 emissions and for other benefits such as fuel-flexibility that would allow vehicles to operate on a range of bio-fuels, conventional fuels, and synthetic fuels to support diversification and/or “greening” of the fuel supply. As presented at the 2006 SAE World Congress1, Renault and Nuvera Fuel Cells previously developed fuel processor technology that achieved automotive size (80 liters) and power (1.4 g/s of hydrogen production) and reduced the startup time from more than 60 minutes to between 1.4 and 3.7 minutes to have CO <100 ppm. This paper presents an overview of the multi-fuel fuel cell power plant along with advances in the fuel processing system (FPS) technology and the testing results obtained since those reported in 2006.

Laboratory and engine tests were carried out to describe the sulphur effect on the NOx adsorbers catalysts efficiency for gasoline lean burn engines. Two main aspects were studied. The first one deals with the NOx storage efficiency of the adsorber under laboratory conditions, especially regarding the SO2 gas phase concentration. The rate of sulfur storing is greatly affected by the SO2 gas concentration. While 6.5 hours are required to get from 70 % NOx reduction to only 35 % when the gas mixture contains 10 ppm SO2, it takes 20 hours with 5 ppm SO2 and more than 60 hours with the 2 ppm SO2 condition. The relationship between the loss in NOx trap performance and SO2 concentration appears to have an exponential shape. The same amount of sulphur (0.8 % mass) is deposited onto the catalyst within 10 hours with the feed gas containing 10 ppm of SO2 and within 50 hours with 2 ppm SO2. Nevertheless, It was shown that the loss in NOx-Trap efficiency is not the same in these two cases.

Many new technologies are being developed to improve the fuel consumption of gasoline engines, including the combination of direct fuel injection with turbocharging in a so-called ‘downsizing’ approach. In such spark ignition engines operating on the Otto cycle, downsizing targets a shift in the operating map such that the engine is dethrottled to a greater extent during normal operation, thus reducing pumping losses and improving fuel consumption. However, even with direct injection, the need for turbine protection fuelling at high load in turbocharged engines - which is important for customer usage on faster European highways such as German Autobahns - brings a fuel consumption penalty over a naturally-aspirated engine in this mode of operation.

Concerns over energy security and global warming are beginning to be a serious issue for society and are also starting to drive customer purchasing decisions across many areas. Against this background there is an increasing call for motor sport to improve its environmental image, despite the fact that the global energy consumption and CO2 emissions attributable to motor sport are a very low proportion of the total. The real issue for motor sport in the face of the wider societal concerns is that, if it is truly at the cutting edge of relevant automotive engineering, it should be configured and managed in such a way as to drive technology for the betterment of mankind. The status quo is, it is contended, increasingly seen to be blatantly energy-profligate in the eyes of many people and this issue must be resolved if motor sport is to demonstrate the wider benefits of the technology developed by the huge financial investments committed to competing at the highest level.