Search Results

Results of engine bench tests on a 1998 heavy-duty diesel engine have confirmed the emissions reduction performance of a U.S. Environmental Protection Agency (EPA) registered platinum/cerium bimetallic fuel borne catalyst (FBC) used with several different catalyzed and uncatalyzed diesel particulate filters (DPF's). Performance was evaluated on both a 450ppm sulfur fuel (No.2 D) and a CARB 50ppm low sulfur diesel (LSD) fuel. Particulate emissions of less than 0.02g/bhp-hr were achieved on several combinations of FBC and uncatalyzed filters on 450ppm sulfur fuel while levels of 0.01g/bhp-hr were achieved for both catalyzed and uncatalyzed filters using the FBC with the low sulfur CARB fuel. Eight-mode steady state testing of one filter and FBC combination with engine timing changes produced a 20% nitrogen oxide (NOx) reduction with particulates (PM) maintained at 0.01g/bhp-hr and no increase in measured fuel consumption.

The Tank-Automotive RD&E Center periodically conducts foreign materiel evaluations to assess the current state of the art for ground vehicle technologies. The Propulsion Laboratory is conducting performance evaluations of an opposed-piston two-stroke diesel tank engine produced by the Kharkov Design Bureau in Ukraine. A key factor in the performance of all two-stroke engines is the scavenging process, which determines how well the cylinders are emptied of exhaust and filled with fresh air. The overall air flow rate is not sufficient to determine this, as a significant amount of air may be lost through the exhaust ports during the scavenging process. The inlet tracer gas method was employed to provide the additional data required. With methane as the tracer, it produced reasonable and consistent data over a wide range of engine speeds and loads. The inlet tracer gas method was found to be an effective tool for measuring the scavenging performance of a running two-stroke diesel engine.

This study compared four different candidate fuels which were prepared by blending different components with a typical No. 2 diesel. Two fuels were blended with a synthetic diesel prepared from natural gas condensate, and all candidate fuels were splash blended with a proprietary additive package from International Fuel Technology Inc. (IFT). These fuels were then compared to the No. 2 diesel and to a California Air Resources Board (CARB) equivalent diesel fuel. The comparisons included fuel properties such as sulfur content, aromatics, cetane, lubricity, distillation; emissions; and fuel consumption. Emission testing was conducted on a 1991 Detroit Diesel Series 60. The Environmental Protection Agency (EPA) transient cycle was utilized for emissions, fuel characterization was performed according to ASTM standards, and fuel consumption was calculated by the carbon balance method.

Sulfur and aromatic compounds in diesel fuel impact the emissions profile of current diesel engines. Fuels that do not contain these components can be made from natural gas using Fischer-Tropsch chemistry. Very little data has been presented comparing the emissions characteristics of current low sulfur diesel to fuels with ultra low levels of sulfur and aromatics in passenger car diesel engines. This study reports on an exhaust emission comparison of currently available conventional diesel fuel to Fischer Tropsch diesel fuel free of aromatics and sulfur comparisons included regulated emissions, air toxics, aldehydes and ketones, particle size distribution, and greenhouse gas emissions. Testing was conducted on a current model diesel passenger car using a chassis dynamometer. Regulated emissions were analyzed according to the Code of Federal Regulations (CFR) Title 40 specifications and requirements of the Environmental Protection Agency (EPA) Federal Test Procedure (FTP).

Semi-volatile organic compounds (SVOC) are a group of compounds that may form during combustion and/or are present in the unburned portion of the fuel and lubricating oil which ultimately become part of the exhaust. Many of these compounds are considered toxic or carcinogenic. Since these compounds are present in very low concentrations in diesel engine exhaust, the methods for sampling, handling, and analyzing these compounds are critical to obtaining representative and repeatable results. Engine testing is typically performed using a dilution tunnel. With a dilution tunnel, the collection of a representative sample is important. Experiments were performed with a modified EPA Method TO-9A to determine the equilibration time and other sampling parameters required for the measurement of SVOC in dilute exhaust. The results show that representative results can be obtained with this method.