Search Results

The ISO TC22/SWG2 - Brake Lining Committee established a task force to determine and analyze root causes for variability during dynamometer brake performance testing. SAE paper 2010-01-1697 “Brake Dynamometer Test Variability - Analysis of Root Causes” [1] presents the findings from the phases 1 and 2 of the “Test Variability Project.” The task force was created to address the issue of test variability and to establish possible ways to improve test-to-test and lab-to-lab correlation. This paper presents the findings from phase 3 of this effort-description of factors influencing test variability based on DOE study. This phase concentrated on both qualitative and quantitative description of the factors influencing friction coefficient measurements during dynamometer testing.

Two methods are allowed in ISO 26262-5 for hardware analysis of random hardware failures. The 1st method is called “Evaluation of Probabilistic Metric for random Hardware Failures”. The 2nd method is called “Evaluation of each cause of safety goal violation”. Advantages of the 2nd method during development of ASIL D Generation 3 Electric Power Steering are presented in this paper. A reliability analysis is one of the important prerequisite for the hardware analysis and this paper shows the best practice for hardware part failure rate estimation using industry standards such as IEC TR 62380. The equally important focus is on a diagnostic coverage of each safety mechanism with respect to residual faults and with respect to relevant dual/latent point faults because any safety design can either benefit from low failure rates or from high diagnostic coverage of safety mechanism to mitigate faults. FMEA is highly recommended by ISO 26262-5 as a part of hardware analysis.

While much research has focused on improving terrain mobility, energy and fuel efficiency of terrain trucks, only a limited amount of investigation has gone into analysis of power distribution between the driving wheels. Distribution of power among the driving wheels has been shown to have a significant effect on vehicle operating characteristics for a given set of operating conditions and total power supplied to the wheels. Wheel power distribution is largely a function of the design of the driveline power dividing units (PDUs). In this paper, 6×6/6×4 terrain truck models are analyzed with the focus on various combinations of PDUs and suspension systems. While these models were found to have some common features, they demonstrate several different approaches to driveline system design.

Electrically Powered Hydraulic Steering (EPHS) was developed in the early 90s and previously applied to vehicle segments B and C (small and medium-sized passenger cars). Till now more than 10 million vehicles are in the field. The advantages consist of the well known power density coming along with the flexible package. Value is added due to the consequent development and usage of electronic control realized in compact physical units. As a result key features for chassis control systems like controllability, high dynamic performance, and low energy consumption are achieved while maintaining mature and robust hydraulic components. Recent market requirements in other segments, e.g. Sport Utility Vehicles (SUV) and Light Commercial Vehicles (LCV) require higher powered motor pump units and lead to the decision to develop products in this direction.

This paper reports the progress that has been made to date on a research program that has as its focus to describe the mechanism of metal pick-up generation on passenger car disc brake pads in correlation with deep rotor scoring. In contrast to other existing generation theories, the new investigation considers other aspects of the initial onset of the metal pick-up.

To develop a free-piston engine-alternator integrative power system for Hybrid Electric Vehicles, the key design parameters, such as reciprocating mass of the piston assembly, compression ratio, the ignition timing, the engine fuel consumption rate and power output, are studied based on the simulation. The results show that, the system simulation model of the free piston engine can predict the in-cylinder pressure vs. the piston's displacement being accurate enough as the test results from reported reference. The model can be employed to optimize the design parameters and to predict the fuel economy and power output. It provides the methods and bases for the free piston engine design and predicting the main performance parameters' values.

In this paper the approach of using modal parameters to detect and locate damage of automobile rear axle under experimental condition is explained. This method uses the changes in the curvature mode of the structure as the damage identification indicator to detect and locate damage. The curvature mode and the damage identification indicator are explained, the process of the identification is introduced. The method is demonstrated with a FEM (Finite Element Method) analysis on a plate under different damage conditions. And the indicator is improved with a weighting function. Then EMA (Experimental Modal Analysis) is conducted on a damaged and an undamaged rear axle of a vehicle to get the modal parameters for the damage identification indicator which later identifies and locates the damages, thus validating the introduced method.

One of the most important means used for suppressing squeal noise in disc brakes is the application of shims on the pad backplates. In many cases this proves a very efficient tool depending on the type of shim applied in the specific cases. Building up knowledge on the effects of shims have been ongoing for several years, and measuring the important parameters characterizing the shims is crucial for understanding how to develop and implement the shims in an optimal way. Several methods are described in literature for measuring the constrained layer damping effect and one method is described for direct measurement of the shear stiffness and shear damping properties. However, up to now no method has been available that can measure and characterize the normal stiffness and damping properties of shims. This is one of the most important properties of shims as it controls the de-coupling effect in the direction of the normal forces.

Plug-in hybrid electric vehicles (PHEVs) provide significantly improvement in fuel economy over conventional vehicles as well as reductions in greenhouse gas and petroleum. Numerous recent reports regarding control strategy, power train configuration, driving pattern, all electric range (AER) and their effects on fuel consumption and electric energy consumption of PHEVs are reported. Meanwhile, the control strategy for engine start-stop and mileage between recharging events from the electricity grid also has an important influence on the petroleum displacement potential of PHEVs, but few reports are published. In this paper, a detailed simulation model is set up for a plug-in series hybrid electric vehicle (PSHEV) employing the AVL CRUISE. The model was employed to predict the AER of the baseline PSHEV using rule-based logical threshold switching control strategy.

In this paper, based on the plug-in series hybrid electric vehicle development project, the vehicle technology solutions and the match of power system parameters were analyzed. The vehicle control strategies were identified and optimized according to plug-in hybrid vehicle features. The plug-in series hybrid, rule-based logic threshold switching control strategy, charge depleting (CD) mode and charge-sustaining (CS) mode are chosen according to the key factors, such as the environment, performance requirements, technical requirements and cost. And then the structure and model of vehicle control strategy were established to carry out vehicle energy management and power system control. The parameter selection, electric drive system matching, energy storage system design based on the requirement of vehicle performance, system architecture and control strategy are presented.

Prediction and analysis of the thermo-mechanical coupling behavior in friction braking system is very important for the design and application of vehicle brakes, such as brake judder, brake squeal, brake wear, brake cracks, brake fade. This paper aims to establish a macro-structural model of the thermo-mechanical dynamics of the ventilated disc brake with asymmetrical outer and inner disc thickness, taking into account the friction-velocity curve of the disc pad couple acquired by testing. On the basis of finite elements analysis of the model, the predictions of the thermo-mechanical responses of the brake disc are presented, including disc transient temperature field and normal stress in radial, circular and axial directions, disc lateral deformation and disc thickness variation. Numerical predictions of the disc surface temperature and later distortion are compared with experimental measurements obtained by thermocouples and non-contact displacement sensors.

An adaptive sideslip angle observer based on discrete extended Kalman filter (DEKF) is proposed in this paper and tire-road friction adaptation is also considered. The single track vehicle model with nonlinear tire characteristics is adopted. The tire parameters can be easily obtained through road test data without using special test rig. Afterwards, this model is discretized and the maximum value of tire-road friction is modeled as the third state variable. Through the measurement of vehicle lateral acceleration and yaw rate, the tire-road adhesion coefficient can be timely updated. Simulations with experimental data from road test and driving simulator have confirmed that DEKF has very high accuracy. The convergent speed of DEKF relies on the magnitude of lateral excitation.

Customers of new vehicles expect their vehicle to provide reliable operation. One path vehicle manufacturers have chosen to meet this expectation is to offer their customers advanced braking systems. Antilock Brakes (ABS) and Traction Control (TC) are two advanced braking systems that have evolved to a point at which many OEM's offer them as standard equipment. Size, weight, and performance have also improved to the point of near transparent operation in many cases. The current direction of braking system evolution is in making Vehicle Stability Control (VSC) widely available as well. VSC adds the ability to assist the driver in negotiating understeer and oversteer, by adding corrective braking and engine torque to the vehicle as appropriate. A large percentage of VSC system modeling is related to the sensors chosen to provide driver and vehicle dynamic information to the system's electronic control unit (ECU).

The continuous decrease in background noise levels inside vehicles has made other noise sources easily noticeable. Specifically, foundation brake rattle noise is a growing concern to the customer. This brake rattle is primarily due to rigid body impact between brake components. Currently, vehicle and brake manufacturing companies use different testing procedures to evaluate brake rattle that include laboratory vibration shakers, full vehicle shakers (four post), chassis dynamometers and vehicle road testing. These evaluations are subjective in most cases. A method is needed to replicate and quantify vehicle brake rattle in the laboratory to help determine the acceptability of a brake system at a component level. This approach would also help to identify the root cause for brake rattle and evaluate design changes to address that rattle. Some guidelines for better quantifying brake rattle using shakers will be proposed in this paper.

This paper reviews the state of the art of CAE simulation and analysis methods on disc brake squeal. It covers complex modes analysis, transient analysis, parametrical analysis, and operational simulation. The advantages and limitations of each analysis method are discussed. This review can help analysts to choose right methods and decide new lines of method development. For completeness, analytic methods dealing with continuum models are also briefly covered. This review was made from those papers that the authors are familiar with. It is not meant to be all-inclusive even though the best possible effort has been attempted.

After obtaining the optimal trajectory through the lane change decision and trajectory planning, the last key technology for the automatic lane change assist system is to carry out the precise and rapid steering actuation according to the front wheel angle demand. Therefore, an automatic lane change system model including a BLDCM (brushless DC motor) model, a steering system model and a vehicle dynamics model is first established in this paper. Electromagnetic characteristics of the motor, the moment of the inertia and viscous friction etc. are considered in these models. Then, a SMC (Sliding Mode Control) algorithm for the steering system is designed to follow the steering angle input. The control torque of the steering motor is obtained through the system model according to steering angle demand. After that, the control current is calculated considering of electromagnetic characteristics of the BLDCM. Debugging and optimization of the control algorithm are done through simulations.

The automatic lane change assist system is an intelligent driving assistance technology oriented to traffic safety, which requires trajectory planning of the lane change maneuver based on the lane change decision. A typical scene of lane change for overtaking is selected, where the front vehicle in the same lane and the rear vehicle in the left lane are deemed to be potential dangerous vehicles through the lane change. Lane change trajectory equation is first established according to the general law of steering wheel angle through lane changes. Based on the relative position, velocity and acceleration information of the dangerous vehicles and the lane change vehicle, motions of these surrounding dangerous vehicles are predicted. At the same time, a multi-objective optimization function is established based on the relative longitudinal safety boundary. The objectives are the minimum safety distance, the lane change time and the front wheel angle.

Research studies have suggested that changes to the ignition system are required to generate a more robust flame kernel in order to secure the ignition process for the future advanced high efficiency spark-ignition (SI) engines. In a typical inductive ignition system, the spark discharge is initiated by a transient high-power electrical breakdown and sustained by a relatively low-power glow process. The electrical breakdown is characterized as a capacitive discharge process with a small quantity of energy coming mainly from the gap parasitic capacitor. Enhancement of the breakdown is a potential avenue effectively for extending the lean limit of SI engine. In this work, the effect of high-power capacitive spark discharge on the early flame kernel growth of premixed methane-air mixtures is investigated through electrical probing and optical diagnosis.

Idle stopping is one of the most important fuel saving methods for hybrid electric vehicle (HEV). While the enriched injection strategy which was employed to ensure reliable ignition of first cycle will leads to even more fuel film stayed in the intake port, all of the liquid film will evaporate randomly and interfere the mixture air-fuel ratio of the followed cycles. The fuel transport of the first cycle should be enhanced to reduce the residual fuel film, and then the control of the cycle-by-cycle air-fuel ratio will become easier and the combustion and HC emissions will also be better. In this paper the mixture preparation characteristics of the unfired first cycle, as well as the combustion and HC emissions characteristics of the fired first cycle under various injection timing strategies such as close-valve injection, mid-valve injection, and open-valve injection were investigated.

It is always a challenging task for the braking industry to maintain consistent friction material behavior during brake system development. Lack of consistency in friction behavior causes significant disruptions in efforts to integrate friction material with the foundation brake system. This is especially true when new friction formulations and/or manufacturing processes are introduced during an application program. Furthermore, every new program has new requirements that introduce new challenges and issues to the brake and friction manufacturers. As issues arise during the Application development, engineers devise countermeasures that often entail new engineering techniques and methods. Sometimes, such countermeasures amount to inventions to cover the inadequacy of lining behavior during brake integration.