Search Results

The ISO TC22/SWG2 - Brake Lining Committee established a task force to determine and analyze root causes for variability during dynamometer brake performance testing. SAE paper 2010-01-1697 “Brake Dynamometer Test Variability - Analysis of Root Causes” [1] presents the findings from the phases 1 and 2 of the “Test Variability Project.” The task force was created to address the issue of test variability and to establish possible ways to improve test-to-test and lab-to-lab correlation. This paper presents the findings from phase 3 of this effort-description of factors influencing test variability based on DOE study. This phase concentrated on both qualitative and quantitative description of the factors influencing friction coefficient measurements during dynamometer testing.

Two methods are allowed in ISO 26262-5 for hardware analysis of random hardware failures. The 1st method is called “Evaluation of Probabilistic Metric for random Hardware Failures”. The 2nd method is called “Evaluation of each cause of safety goal violation”. Advantages of the 2nd method during development of ASIL D Generation 3 Electric Power Steering are presented in this paper. A reliability analysis is one of the important prerequisite for the hardware analysis and this paper shows the best practice for hardware part failure rate estimation using industry standards such as IEC TR 62380. The equally important focus is on a diagnostic coverage of each safety mechanism with respect to residual faults and with respect to relevant dual/latent point faults because any safety design can either benefit from low failure rates or from high diagnostic coverage of safety mechanism to mitigate faults. FMEA is highly recommended by ISO 26262-5 as a part of hardware analysis.

While much research has focused on improving terrain mobility, energy and fuel efficiency of terrain trucks, only a limited amount of investigation has gone into analysis of power distribution between the driving wheels. Distribution of power among the driving wheels has been shown to have a significant effect on vehicle operating characteristics for a given set of operating conditions and total power supplied to the wheels. Wheel power distribution is largely a function of the design of the driveline power dividing units (PDUs). In this paper, 6×6/6×4 terrain truck models are analyzed with the focus on various combinations of PDUs and suspension systems. While these models were found to have some common features, they demonstrate several different approaches to driveline system design.

Electrically Powered Hydraulic Steering (EPHS) was developed in the early 90s and previously applied to vehicle segments B and C (small and medium-sized passenger cars). Till now more than 10 million vehicles are in the field. The advantages consist of the well known power density coming along with the flexible package. Value is added due to the consequent development and usage of electronic control realized in compact physical units. As a result key features for chassis control systems like controllability, high dynamic performance, and low energy consumption are achieved while maintaining mature and robust hydraulic components. Recent market requirements in other segments, e.g. Sport Utility Vehicles (SUV) and Light Commercial Vehicles (LCV) require higher powered motor pump units and lead to the decision to develop products in this direction.

This paper reports the progress that has been made to date on a research program that has as its focus to describe the mechanism of metal pick-up generation on passenger car disc brake pads in correlation with deep rotor scoring. In contrast to other existing generation theories, the new investigation considers other aspects of the initial onset of the metal pick-up.

In this paper the approach of using modal parameters to detect and locate damage of automobile rear axle under experimental condition is explained. This method uses the changes in the curvature mode of the structure as the damage identification indicator to detect and locate damage. The curvature mode and the damage identification indicator are explained, the process of the identification is introduced. The method is demonstrated with a FEM (Finite Element Method) analysis on a plate under different damage conditions. And the indicator is improved with a weighting function. Then EMA (Experimental Modal Analysis) is conducted on a damaged and an undamaged rear axle of a vehicle to get the modal parameters for the damage identification indicator which later identifies and locates the damages, thus validating the introduced method.

One of the most important means used for suppressing squeal noise in disc brakes is the application of shims on the pad backplates. In many cases this proves a very efficient tool depending on the type of shim applied in the specific cases. Building up knowledge on the effects of shims have been ongoing for several years, and measuring the important parameters characterizing the shims is crucial for understanding how to develop and implement the shims in an optimal way. Several methods are described in literature for measuring the constrained layer damping effect and one method is described for direct measurement of the shear stiffness and shear damping properties. However, up to now no method has been available that can measure and characterize the normal stiffness and damping properties of shims. This is one of the most important properties of shims as it controls the de-coupling effect in the direction of the normal forces.

Prediction and analysis of the thermo-mechanical coupling behavior in friction braking system is very important for the design and application of vehicle brakes, such as brake judder, brake squeal, brake wear, brake cracks, brake fade. This paper aims to establish a macro-structural model of the thermo-mechanical dynamics of the ventilated disc brake with asymmetrical outer and inner disc thickness, taking into account the friction-velocity curve of the disc pad couple acquired by testing. On the basis of finite elements analysis of the model, the predictions of the thermo-mechanical responses of the brake disc are presented, including disc transient temperature field and normal stress in radial, circular and axial directions, disc lateral deformation and disc thickness variation. Numerical predictions of the disc surface temperature and later distortion are compared with experimental measurements obtained by thermocouples and non-contact displacement sensors.

An adaptive sideslip angle observer based on discrete extended Kalman filter (DEKF) is proposed in this paper and tire-road friction adaptation is also considered. The single track vehicle model with nonlinear tire characteristics is adopted. The tire parameters can be easily obtained through road test data without using special test rig. Afterwards, this model is discretized and the maximum value of tire-road friction is modeled as the third state variable. Through the measurement of vehicle lateral acceleration and yaw rate, the tire-road adhesion coefficient can be timely updated. Simulations with experimental data from road test and driving simulator have confirmed that DEKF has very high accuracy. The convergent speed of DEKF relies on the magnitude of lateral excitation.

Customers of new vehicles expect their vehicle to provide reliable operation. One path vehicle manufacturers have chosen to meet this expectation is to offer their customers advanced braking systems. Antilock Brakes (ABS) and Traction Control (TC) are two advanced braking systems that have evolved to a point at which many OEM's offer them as standard equipment. Size, weight, and performance have also improved to the point of near transparent operation in many cases. The current direction of braking system evolution is in making Vehicle Stability Control (VSC) widely available as well. VSC adds the ability to assist the driver in negotiating understeer and oversteer, by adding corrective braking and engine torque to the vehicle as appropriate. A large percentage of VSC system modeling is related to the sensors chosen to provide driver and vehicle dynamic information to the system's electronic control unit (ECU).

The continuous decrease in background noise levels inside vehicles has made other noise sources easily noticeable. Specifically, foundation brake rattle noise is a growing concern to the customer. This brake rattle is primarily due to rigid body impact between brake components. Currently, vehicle and brake manufacturing companies use different testing procedures to evaluate brake rattle that include laboratory vibration shakers, full vehicle shakers (four post), chassis dynamometers and vehicle road testing. These evaluations are subjective in most cases. A method is needed to replicate and quantify vehicle brake rattle in the laboratory to help determine the acceptability of a brake system at a component level. This approach would also help to identify the root cause for brake rattle and evaluate design changes to address that rattle. Some guidelines for better quantifying brake rattle using shakers will be proposed in this paper.

This paper reviews the state of the art of CAE simulation and analysis methods on disc brake squeal. It covers complex modes analysis, transient analysis, parametrical analysis, and operational simulation. The advantages and limitations of each analysis method are discussed. This review can help analysts to choose right methods and decide new lines of method development. For completeness, analytic methods dealing with continuum models are also briefly covered. This review was made from those papers that the authors are familiar with. It is not meant to be all-inclusive even though the best possible effort has been attempted.

After obtaining the optimal trajectory through the lane change decision and trajectory planning, the last key technology for the automatic lane change assist system is to carry out the precise and rapid steering actuation according to the front wheel angle demand. Therefore, an automatic lane change system model including a BLDCM (brushless DC motor) model, a steering system model and a vehicle dynamics model is first established in this paper. Electromagnetic characteristics of the motor, the moment of the inertia and viscous friction etc. are considered in these models. Then, a SMC (Sliding Mode Control) algorithm for the steering system is designed to follow the steering angle input. The control torque of the steering motor is obtained through the system model according to steering angle demand. After that, the control current is calculated considering of electromagnetic characteristics of the BLDCM. Debugging and optimization of the control algorithm are done through simulations.

The automatic lane change assist system is an intelligent driving assistance technology oriented to traffic safety, which requires trajectory planning of the lane change maneuver based on the lane change decision. A typical scene of lane change for overtaking is selected, where the front vehicle in the same lane and the rear vehicle in the left lane are deemed to be potential dangerous vehicles through the lane change. Lane change trajectory equation is first established according to the general law of steering wheel angle through lane changes. Based on the relative position, velocity and acceleration information of the dangerous vehicles and the lane change vehicle, motions of these surrounding dangerous vehicles are predicted. At the same time, a multi-objective optimization function is established based on the relative longitudinal safety boundary. The objectives are the minimum safety distance, the lane change time and the front wheel angle.

Research studies have suggested that changes to the ignition system are required to generate a more robust flame kernel in order to secure the ignition process for the future advanced high efficiency spark-ignition (SI) engines. In a typical inductive ignition system, the spark discharge is initiated by a transient high-power electrical breakdown and sustained by a relatively low-power glow process. The electrical breakdown is characterized as a capacitive discharge process with a small quantity of energy coming mainly from the gap parasitic capacitor. Enhancement of the breakdown is a potential avenue effectively for extending the lean limit of SI engine. In this work, the effect of high-power capacitive spark discharge on the early flame kernel growth of premixed methane-air mixtures is investigated through electrical probing and optical diagnosis.

It is always a challenging task for the braking industry to maintain consistent friction material behavior during brake system development. Lack of consistency in friction behavior causes significant disruptions in efforts to integrate friction material with the foundation brake system. This is especially true when new friction formulations and/or manufacturing processes are introduced during an application program. Furthermore, every new program has new requirements that introduce new challenges and issues to the brake and friction manufacturers. As issues arise during the Application development, engineers devise countermeasures that often entail new engineering techniques and methods. Sometimes, such countermeasures amount to inventions to cover the inadequacy of lining behavior during brake integration.

The vehicle system is actually a strongly nonlinear system with stochastic parameters. In this paper, the nonlinearities of suspension, tire and seat are analyzed, and the nonlinear dynamics model of driver-vehicle system with 8 degrees of freedom (DOFs) is built. The bifurcation and chaotic motion of the deterministic system under Sinusoid excitations considering the time delay between the front and rear tires are studied. Then, the stochastic feature of the equivalent stiffness and damping coefficients of suspension, tire and seat are assumed to be the normal distribution, and the nonlinear model with random parameters is obtained. The nonlinear dynamics of stochastic nonlinear driver-vehicle system is analyzed and compared through numerical simulation.

Ion current sensing, which usually employs a spark plug as its sensor to obtain feedback signal from different types of combustion in SI engines, may be applied to HCCI combustion sensing instead of a prohibitively expensive piezoelectric pressure transducer. However, studies showed that the ion current detected by a spark plug sensor is a localized signal within the vicinity of the sensor's electrode gap, being affected by conditions around it. To find out better and feasible ion probe positions, a 3D-CFD model with a detailed surrogate mechanism containing 1423 species and 6106 reactions was employed to study the effect of stratification on ion distribution in HCCI combustion. The simulation results indicate that the monitor probe 1, 8 and 9 are more stable and reliable than the others. IONmax and dIONmax are more accurate to estimate CA50 and dQmax respectively.

Based on the experimental data of true stress-strain measured by DIC (Digital Image Correlation) combined with the data from a tensile test machine, the methodology for establishing a constitutive model for Ti40 alloy sheet is presented in this paper. The procedure is demonstrated by building the constitutive relationship for Ti40 alloy sheet. As the verification of the constitutive relationship, a force-displacement diagram is simulated by FEA (Finite Element Analysis). A comparison of force-displacement diagram obtained separately by FEA and the tensile test machine is made and the result shows that the method for establishing the constitutive relationship for Ti40 alloy sheet presented in this paper are reliable and considerately accurate.

The control in transient conditions when hydraulic brake and regenerative brake switch mutually is the key technical issue about electric vehicle hybrid brake system, which has a direct influence on the braking feel of driver and vehicle braking comfort. A coordination control system has been proposed, including brake force distribution correction module and motor force compensation module. Brake force distribution correction module has fixed the distribution results in hydraulic brake force intervention condition, hydraulic brake force evacuation condition and regenerative brake force low speed evacuation condition. Motor compensation module has compensated hydraulic system with motor system, which has fast and accurate response, thus the response of whole hybrid system has been improved.