Search Results

This work reports on measurement and analysis of the galvanic interaction between steel self-piercing rivets (SPRs) having several different surface conditions and magnesium alloy substrates under consideration for use in automotive structural assemblies. Rivet surface conditions included uncoated steel, conventional Zn-Sn barrel plating and variations of commercial aluminizing processes, including supplemental layers and sealants. Coating characteristics were assessed using open circuit potential (OCP) measurement, potentiodynamic polarization scanning (PDS), and electrochemical impedance spectroscopy (EIS). The degree of galvanic coupling was determined using zero-resistance ammeter (ZRA) and the scanning vibrating electrode technique (SVET), which also permitted characterization of galvanic current flows in situ.

The Cummins M-11 high soot diesel engine test is a key tool in evaluating lubricants for the new PC-7 (CH-4) performance category. M-11 rocker arms and crossheads from tests with a wide range of lubricant performance were studied by surface analytical techniques. Abrasive wear by primary soot particles is supported by the predominant appearance of parallel grooves on the worn parts with their widths matching closely the primary soot particle sizes. Soot abrasive action appears to be responsible for removing the protective antiwear film and, thus, abrades against metal parts as well. Subsequent to the removal of the antiwear film, carbide particles, graphite nodules, and other wear debris are abraded, either by soot particles or sliding metal-metal contact, from the crosshead and rocker arm metal surfaces. These particles further accelerate abrasive wear. In addition to abrasive wear, fatigue wear was evident on the engine parts.

This paper reports the progress that has been made to date on a research program that has as its focus to describe the mechanism of metal pick-up generation on passenger car disc brake pads in correlation with deep rotor scoring. In contrast to other existing generation theories, the new investigation considers other aspects of the initial onset of the metal pick-up.

The goal of the present work is to reduce the environmental impact of car gasoline engines by developing lightweight engine components. The use of light-weight metals such as aluminum results in substantial reductions in CO2 emissions. Traditionally aluminum alloys have been restricted to low temperature applications because of their poor mechanical properties at elevated temperature. However, novel fabrication methods such as spray forming and rapid solidification have overcome the temperature limitation. Coupled with a surface coating designed to withstand corrosion and wear at elevated temperatures, these high performance alloys may be considered to replace steel-based components in automotive engines. In this work, hypereutectic aluminum-silicon (Al-Si) alloys produced via different fabrication routes were tested for laser coating with a nickel-chromium alloy. Experimental results demonstrating the response of these alloys to laser coating are presented.

The electrochemical and corrosion behavior of metals in aqueous environments has received substantial attention. However, relatively little work has been devoted to the electrochemistry and corrosion of metals in non-aqueous environments. Now, with greater pressures to increase fuel efficiencies and decrease exhaust emissions, alternatives and additives to gasoline (including methanol and ethanol) are receiving increased attention from government agencies and automobile manufacturers. Unfortunately, fundamental studies of the corrosion behavior of metals in these solutions are scarce. The objective of the present work is to investigate the electrochemical and corrosion behavior of iron in methanolic solutions containing Cl, H+, SO42-, and H2O. To accomplish this, a full factorial design test matrix was developed to systematically evaluate the effects of these impurities on the corrosion behavior of iron.

Steering control devices are used by people who have difficulty gripping the steering wheel. These devices have projections that may extend up to 14 cm toward the occupant. Testing indicated that contact with certain larger steering control devices with tall rigid projections could severely injure a driver in a frontal collision. In order to reduce this injury risk, an alternative, less injurious design was developed and tested. This design, which included replacing unyielding aluminum projections with compliant plastic ones, produced significantly lower peak contact pressure and less damage to the chest of a cadaver test subject, while maintaining the strength necessary to be useful.

Since the inception of the IIHS Small Overlap Impact (SOI) test in 2012, automotive manufacturers have implemented many solutions in the vehicle body structure to achieve an IIHS “Good” rating. There are two main areas of the vehicle: forward of vehicle cockpit and immediately surrounding the vehicle cockpit, which typically work together for SOI to mitigate crash energy and prevent intrusion into the passenger zones. The structures forward of vehicle cockpit are designed to either 1) absorb vehicle energy from impact to the barrier, or 2) provide enough strength and rigidity to aid deflection of the vehicle away from the barrier. The structures which are immediately surrounding the vehicle cockpit (known as pillars and rocker/sills) are traditionally components designed to be highly rigid sheet metal panels to protect the occupant during crash events.

Multiple experimental studies were performed on galling intiation for variety of tooling materials, coatings and surface treatments, sheet materials with various surface textures and lubrication. Majority of studies were performed for small number of samples in laboratory conditions. In this paper, the methodology of screening experiment using different combinations of tooling configurations and sheet material in the lab followed by the high volume small scale U-bend performed in the progressive die on the mechanical press is discussed. The experimental study was performed to understand the effect of the interface between the sheet metal and the die surface on sheet metal flow during stamping operations. Aluminum sheet AA5754 2.5mm thick was used in this experimentation. The sheet was tested in laboratory conditions by pulling between two flat insert with controllable clamping force and through the drawbead system with variable radii of the female bead.