Search Results

Real driving emission (RDE) tests are influenced by factors such as data processing methods, driving behaviors, and environmental conditions. Therefore, being able to effectively identify test influence factors is particularly important for RDE emissions-based calibrations. In order to investigate the correlation between data processing methods, driving behaviors and vehicle emissions, the moving average window (MAW) method and cumulative averaging (CA) method were used to compare and analyze the RDE tests data of a light-duty gasoline vehicle under different driving modes in this study. The results showed that in MAW method, carbon monoxide (CO) emissions of urban and total trips calculated by using the front to back window division order were slightly lower compared to the back to front window division order, with an average reduction of 4.68% and 6.33%, respectively. For carbon dioxide (CO2) emissions, the order of window division had the opposite effect as for CO emissions.

To improve the thermal efficiency and inhibit the knock tendency of gasoline direct injection (GDI) engines, water injection technology has a bright application prospect. Utilize gasoline/water mixture as a way to realize this technology can lower the cost of modifying the engines and bring potential for better spray qualities. Hence it is essential to give deep insight into the effects of water on spray atomization, evaporation and mixture formation for gasoline/water mixtures. A spray synchronous measurement experimental system with a single hole nozzle is used to investigate the spray morphology, spray width and droplet size distribution of gasoline/water mixtures sprays under different water volume fractions (0 %, 20 %, 35 %) and different initial fuel temperatures (50 °C~ 130 °C). There are critical temperatures of 80 °C(G100), 100 °C(G80) and 120 °C(G65), above which the ‘collapsed’ spray appears.

High altitudes have a significant effect on the real driving emissions (RDE) of vehicles due to lower pressure and insufficient oxygen concentration. In addition, type approval tests for light-duty vehicles are usually conducted at altitudes below 1000 m. In order to investigate the influence of high altitude on vehicles fuel economy and emissions, RDE tests procedure had been introduced in the China VI emission regulations. In this study, the effect of altitude on fuel economy and real road emissions of three light-duty gasoline vehicles was investigated. The results indicated that for vehicles fuel economy, fuel consumption (L/100 km) for the tested vehicles decreased while the mean exhaust temperature increased with an increase in altitudes. Compared to near sea level, the fuel consumption (L/100 km) of the tested vehicle was reduced by up to 23.28%.

NHTSA released the FMVSS226 Standard in 2011, and defined the requirements for ejection mitigation systems, which limit the linear travel of headform by 100mm. In China regulations, there are similar requirements starting in 2021. Therefore, on the basis of the existing airbag design, adding the rollover protection function becomes a challenge for the airbag development. During the development of the curtain airbag, the cushion design, inflator type, and the fold pattern, all have an important influence on the airbag unfolding direction, the airbag positioning time and the airbag internal pressure, and then significantly affect the occupant protection performance afterwards. In order to reduce the cost and shorten the development time, it is necessary to predict the process of cushion deployment kinematics and the internal pressure of the airbag with high refinement, and based on it to predict and evaluate the FMVSS226 ejection mitigation performance.

Ultra-lean combustion of GDI engine could achieve higher thermal efficiency and lower NOx emissions, but it also faces challenges such as ignition difficulties and low-speed flame propagation. In this paper, the sparked-spray is proposed as a novel ignition method, which employs the spark to ignite the fuel spray by the cooperative timing control of in-cylinder fuel injection and spark ignition and form a jet flame. Then the jet flame fronts propagate in the ultra-lean premixed mixture in the cylinder. This combustion mode is named Sparked-Spray Induced Combustion (SSIC) in this paper. Based on a 3-cylinder 1.0L GDI engine, a 3D simulation model is established in the CONVERGE to study the effects of ignition strategy, compression ratio, and injection timing on SSIC with a global equivalence ratio of 0.50. The results show it is easier to form the jet flame when sparking at the spray front because the fuel has better atomization and lower turbulent kinetic energy at the spray front.