Search Results

The present paper describes an application of non-parametric shape optimization to disc brake squeal phenomena. A main problem is defined as complex eigenvalue problem in which the real part of the complex eigenvalue causing the brake squeal is chosen as an objective cost function. The Fre´chet derivative of the objective cost function with respect to the domain variation, named as the shape derivative of the objective cost function, is evaluated using the solution of the main problem and the adjoint problem. A selection criterion of the adoptive mode number in component mode synthesis (CMS), which is used in the main problem, is presented in order to reduce the computational error in complex eigenvalue pairs. A scheme to solve the shape optimization problem is presented using an iterative algorithm based on the H1 gradient method for reshaping. For an application of the optimization method, a numerical example of a practical disc brake model is presented.

A communication system that uses roadside beacons to broadcast road and traffic information and private messages to vehicles has been developed. The system, called Road/Automobile Communication System (RACS), was the result of a joint research project involving the Public Works Research Institute and 25 private-sector corporations. This paper contains an outline of RACS and of an onboard system developed by TOYOTA and presents the results of field tests conducted in the Tokyo area. The results not only verify the capability of the RACS system and the effectiveness of the in-vehicle equipment but also indicate the potential of such a beacon based network to improve traffic jam and driving safety whilst providing enhanced communication facilities without increasing radio-wave congestion.

Oil film thickness is one of the most important issues for optimization of bearing design. A technique has been developed to measure oil film thickness by noting the change in capacitance between the shaft and a thin-film electrode of several micrometers thickness formed on the surface of a bearing. The authors applied this technique to the main journals of an automobile engine and measured the oil film thickness up to maximum speed and full load. The oil film thickness became thinner with increased engine load, and then turned thicker with increased engine speed.

Detergent additives in automotive gasoline fuel are mainly designed to reduce deposit formation on intake valves and fuel injectors, but it has been reported that some additives may contribute to CCD formation. Therefore, a standardized bench engine test method for CCDs needs to be developed in response to industry demands. Cooperative research between the Petroleum Association of Japan (PAJ) and the Japan Automobile Manufacturers Association, Inc. (JAMA), has led to the development of a 2.2L Honda engine dynamometer-based CCD test procedure to evaluate CCDs from fuel additives. Ten automobile manufacturers, nine petroleum companies and the Petroleum Energy Center joined the project, which underwent PAJ-JAMA round robin testing. This paper describes the CCD test development activities, which include the selection of an engine and the determination of the optimum test conditions and other test criteria.

The hybrid system has the typical advantage that it can realize various types of system control, because the system has two power units, engine and motor. On the other hand, however, constraints are increasing due to the complexity of the vehicle system. Compared to the conventional HILS construction and application, there are mainly two typical characteristics or themes for HV-HILS (i.e. HILS for hybrid vehicle control development). Firstly, HV-HILS requires full vehicle simulation environment, because the plural ECU control logic is intricately intertwined. Secondly, recent HILS system needs to run with more accurate or complicated plant models which are necessary to develop more accurate vehicle control logic.

We urgently need to develop the next generation of automotive technology to support energy conservation and the global environment. For this we need an advancement of the Laboratory Automation System (LAS). However, restructuring the hardware and software of the LAS requires enormous amounts of time and costs. To solve the problems of the LAS development, we formed a user-vendor working group, which then established the common rules of LAS and IMACS (Integrated Measurement And Control System). IMACS are software-centered rules, characterized by the stratification of LAS and the interface called software parts. So far, we have integrated IMACS into five engineering fields. A total of 11 testing machine vendors participated in the development. We manufactured about 350 software parts and made their specifications openly available. As the next step, we are collecting software parts by deleting redundant functions.

The finite element method (FEM) is effective for analyzing brake squeal phenomena. Although FEM analysis can be used to easily obtain squeal frequencies and complex vibration modes, it is difficult to identify how to modify brake structure design or contact conditions between components. Therefore, this study deals with a practical design method using sensitivity analysis to reduce brake squeal, which is capable of optimizing both the structure of components and contact conditions. A series of analysis processes that consist of modal reduction, complex eigenvalue analysis, sensitivity analysis and optimization analysis is shown and some application results are described using disk brake systems.

The design of the newly developed Toyota AZ series 4 cylinder engine has been optimized through both simulations and experiments to improve heat transfer, cooling water flow, vibration noise and other characteristics. The AZ engine was developed to achieve good power performance and significantly reduced vibration noise. The new engine meets the LEV regulations due to the improved combustion and optimized exhaust gas flow. A major reduction in friction has resulted in a significant improvement in fuel economy compared with conventional models. It also pioneered a newly developed resin gear drive balance shaft.

The Vapor Reducing Fuel Tank System (Bladder Tank System) using a flexible plastic membrane (Bladder Membrane) was newly developed in order to reduce the amount of vaporized gasoline in a steel fuel tank. This Bladder Membrane is flexible to expand in proportion to a fuel volume and prevents the permeation of the vaporized gasoline. As a result of our initial study for various materials, we decided to apply a multi-layer plastic material which could achieve both low fuel permeability and good flexibility. This multi-layer material consists of polyethylene(PE) for structural material and polyamide(PA) for low permeability. The modulus of the PE needs to achieve a sufficient flexibility in order to keep the movement of the membrane. While PA material must have not only low fuel permeability but also strong adhesion with the structural material of PE. We also clarify the membrane design to keep a good flexibility and to reduce a strain.

In preparation for compliance with California's SULEV standard and Euro STAGE 4 standard, which will take effect in 2002 and 2005, respectively, we have developed a laminated planar oxygen sensor. The developed sensor has the following characteristics: high thermal conductivity and superior dielectric characteristic, due to direct joining of the heater element alumina substrate and the sensor element zirconia electrolyte; low heat stress at temperature rise, due to optimized heater design; superior sensor protection from water droplets, and improved sensor response, due to optimized arrangement of intake holes in the sensor cover. With these characteristics, the developed oxygen sensor can be activated in 10 seconds after cold start. This report describes the technologies we used to develop the early-activation oxygen sensor.

Lower extremity injuries in frontal automotive crashes usually occur with footwell intrusion where both the knee and foot are constrained. In order to identify factors associated with tibial shaft injury, a series of numerical simulations were conducted using a finite element model of the whole human body. These simulations demonstrated that tibial mid-shaft injuries in frontal crashes could be caused by an abrupt change in velocity and a high rate of footwell intrusion.

This paper is a study of the On-Board Diagnosis (OBD), a constituent element of the automotive electronic diagnosis system, together with its support functions. With regard to the OBD, we have listed and explained the principles of various diagnostic methods and their advantages and disadvantages. In addition, we have also commented on design factors and concepts. As to the support functions, nameiy diagnostics communication and diagnostic scan tool, drive recorder, and also IT, we have made recommendations on their future development in view of the functional division of roles with respect to the OBD in light of their respective characteristics.

A highly reliable all-mechanical air bag system has been developed with a production cost lower than the electrical air bag system. All components, such as the bag, inflator and sensor are integrated into the steering wheel. Regarding the sensor design, we first discussed the requirements of the sensor to optimize the driver's protection, and then we designed it using a simulation method. We have confirmed by crash tests that this method is correct, and have found that this system is effective for reducing facial injuries.

This paper analyzes the vibration of open-top cars known as lateral shake. The characteristics of the phenomenon were identified by means of road tests and a test method called the shake test was devised to reproduce these characteristics in order that the respective roles of the suspension, body and engine could be determined. On the basis of the analysis findings, a simple but practical simulation model was realized and used to investigate various methods of reducing lateral shake. The simulations indicated that although changing the natural frequency of the suspension has little effect, increasing the natural torsional frequency of the body and/or utilizing the engine as a dynamic damper results in a significant improvement. Further experiments conclusively demonstrated that by optimizing the body structure in accordance with FEM analysis results and optimizing the spring constant of the engine mounts, the level of lateral shake can be halved.

Recycling has become, and will continue to be one of the key technical issues for the automotive industry's role in protection of the global environment. Continued increases in vehicle registrations and use of non-metallic automotive materials will present a increasing opportunity for the utilization of currently wasted resources. Toyota has set up a management body and continues efforts to establish the necessary technologies and strategies for reduction and recovery of these wasted materials as valuable resources. Automakers worldwide are currently investigating numerous technically feasible recycling methodologies. These technologies may be useful for post-use vehicle recycling, but will require further development. It is important to focus current efforts on investigation of as many of these as possible in cooperation with related organizations.

Quality control of gasoline constituents and its effect on the Intake Valve Deposits (IVD) has become a recent issue. In this paper, the effects of gasoline and oil quality on intake valve deposits were investigated using an Intake Valve Deposit Test Bench and a Sludge Simulator. The deposit formation from the gasoline maximized at an intake valve temperature of approximately 160 °C, and the deposits formed from the engine oil were maximum at approximately 250 °C. Therefore, the contribution of the gasoline or the engine oil appears to depend on the engine conditions. The gasoline which contains MTBE or ethanol with no detergent additive slightly increases the deposition amount. The gasoline with a superior detergent significantly decreases the deposition amount even when MTBE or ethanol is blended in the gasoline. Appropriate detergent fuel additive retards the oil deterioration.

Finite element aodels have been developed to analyze drive line and suspension vibration. For the analysis of booming noise, we have addressed the optimization of the differential gear carrier mounting system by using a virtual system and realization of it considering many constraints. To reduce the differential whine noise, a simulation method considering the transmitting error of the differential gear was applied. And we have approached for the subtle arrangements of many structural resonances with detail research of the drive line and suspension. For the reduction of road noise, we adopted the approach of shifting the node of the rear suspension member mode.

A high strength and high toughness new bainitic steel has been developed which shows comparable mechanical properties, fatigue property, and machinability to those of quenched and tempered SAE 5140. The heat treatment of the bainitic steel is aging after hot forging in order to improve ratio of 0.2% proof stress and tensile strength (i.e. yield ratio) and to avoid warpage associated with quenching. The new bainitic steel has been applied to the slender and lightweight lower arms for automotive suspension. As a result, the total production costs in the lower arms have been reduced by nearly 15 percent.

A practical shape optimization technique is presented. We employed the basis vector method to parameterize the shape of the structural domain that is usually discretized by the finite element method. VMA/GENESIS software, the optimization system with finite element analysis, sensitivity analysis, and numerical optimization capabilities, was used for this study. Various design problems such as body, chassis, and engine parts design are solved to demonstrate the effectiveness and the robustness of the present approach for automotive applications.

The purposes of this paper are to develop a new laboratory oxidation stability testing method and to clarify factors relative to the viscosity increase of engine oil. Polymerized products, obtained from the oil after a JASO M333-93 engine test, were found to consist mainly of carboxyl, nitrate and nitro compounds and to increase the oil viscosity. A good similarity between the JASO M333-93 test and the laboratory simulation test was found for the polymerized products. The products were obtained not by heating oil only in air but by heating oil while supplying a synthetic blowby gas consisting of fuel pyrolysis products, NO, SO2 and air. The laboratory test has also revealed that the viscosity increase depends on oil quality, organic Fe content and hydrocarbon composition in the fuel. Moreover, it has been found that blowby gas and organic Fe accelerate ZnDTP consumption and that aromatics concentration in the fuel correlates with the viscosity increase of oil.