Search Results

In the last ten year the mechanical power output of car engine increased significantly. This result has been possible especially through new injection systems that brought to an optimization of the combustion (direct injection, common rail) and to an improvement of the turbocharging. Moreover, these technical devices brought a reduction of the exhaust emissions and an increasing of the engine efficiency. In particular, the specific power is increased from 34 kW/liter of 1992 to the 63 kW/liter of 2010. Furthermore, the pressure peaks into the combustion chamber and the fuel injection pressure have been increased to the aim of emission reduction and higher engine efficiency. In this scenario, car manufacturers are following the direction of the engine downsizing that means to have the same engine power by a lower engine displacement.

Automotive exhaust systems give a major contribution to the sound quality of a vehicle and must be properly designed in order to produce acceptable acoustic performances. Obviously, noise attenuation is strictly related to the used materials and to its internal geometry. This last influences the wave propagation and the gas-dynamic field. The purpose of this paper is to describe advantages and disadvantages of different numerical approaches in evaluating the acoustic performance in terms of attenuation versus frequency (Transmission Loss) of a commercial two perforated tube muffler under different conditions. At first, a one-dimensional analysis is performed through the 1D GTPower® code, solving the nonlinear flow equations which characterize the wave propagation phenomena. The muffler is characterized as a network of properly connected pipes and volumes starting from 3D CAD information. Then, two different 3D analyses are performed within the commercial STS VNOISE® code.

In this paper, an experimental and numerical analysis of combustion process and knock occurrence in a small displacement spark-ignition engine is presented. A wide experimental campaign is preliminarily carried out in order to fully characterize the engine behavior in different operating conditions. In particular, the acquisition of a large number of consecutive pressure cycle is realized to analyze the Cyclic Variability (CV) effects in terms of Indicated Mean Effective Pressure (IMEP) Coefficient of Variation (CoV). The spark advance is also changed up to incipient knocking conditions, basing on a proper definition of a knock index. The latter is estimated through the decomposition and the FFT analysis of the instantaneous pressure cycles. Contemporary, a quasi-dimensional combustion and knock model, included within a whole engine one-dimensional (1D) modeling framework, are developed. Combustion and knock models are extended to include the CV effects, too.

The Direct Injection (DI) of gasoline in Spark Ignition (SI) engines is very attractive for fuel economy and performance improvements in spark ignition engines. Gasoline direct injection (GDI) offers the possibility of multi-mode operation, homogeneous and stratified charge, with benefits respect to conventional SI engines as higher compression ratio, zero pumping losses, control of the ignition process at very lean air-fuel mixture and good cold starting. The impingement of liquid fuel on the combustion chamber wall is generally one of the major drawbacks of GDI engines because its increasing of HC emissions and effects on the combustion process; in the wall guided engines an increasing attention is focusing on the fuel film deposits evolution and their role in the soot formation. Hence, the necessity of a detailed understanding of the spray-wall impingement process and its effects on the fuel distribution. The experimental results provide a fundamental data base for CFD predictions.

The aim of this study is to investigate the effect of ethanol-gasoline mixtures on cold emissive behavior of commercial motorcycles. For the newly sold motorcycles, equipped with a three-way catalyst and electronic mixture control, CO and HC cold additional emissions, if compared with those exhausted in hot conditions, represent an important proportion of total emissions. On the other hand, ethanol is known as potential alcohol alternative fuel for spark ignition engines, which can be blended with gasoline to increase oxygen content and then to decrease emissions. From this explanations, a research on cold start emissions of motorcycles using ethanol-gasoline mixtures was conducted.

Nowadays, due to catalyst improvements and electronic mixture control of last generation vehicles equipped with internal combustion engine, the most significant part of the total emissions of carbon monoxide and unburned hydrocarbons takes place during the cold phase, if compared with those exhausted in hot conditions, with a clear consequence on air quality of urban contexts. The purpose of this research, developed by the Department of Industrial Engineering of the University of Naples Federico II with reference to an European background, is a deeper analysis of the engine and after-treatment system behaviour within the cold start transient and the evaluation of cold start additional emissions: a methodology was developed and optimized to evaluate the cold transient duration, the emitted quantities during the cold phase and the relevant time-dependence function.

A new generation of highly downsized SI engines with specific power output around or above 150 HP/liter is emerging in the sport car market sector. Technologies such as high-boosting, direct injection and downsizing are adopted to increase power density and reduce fuel consumption. To counterbalance the increased risks of pre-ignition, knock or mega-knock, currently made turbocharged SI engines usually operate with high fuel enrichments and delayed (sometimes negative) spark advances. The former is responsible for high fuel consumption levels, while the latter induce an even lower A/F ratio (below 11), to limit the turbine inlet temperature, with huge negative effects on BSFC. A possible solution to increase knock resistance is investigated in the paper by means of 3D-CFD analyses: water/methanol emulsion is port-fuel injected to replace mixture enrichment while preserving, if not improving, indicated mean effective pressure and knock safety margins.

In recent years, in order to optimize performance and exhaust emissions of internal combustion engines, the design of auxiliary systems assumed a particular importance especially due to the need to obtain higher efficiency and reduce power losses required by these components. In this sense, looking at the lubrication circuit, it appears important to use solutions that allow to optimize the fluid dynamics of both the ducts and the pump. In this paper a tridimensional CFD analysis of a lubrication circuit oil pump of a modern high-performance engine will be shown. In this particular application there is a variable displacement pump used to optimize the operative conditions of the lubricant circuit in all engine running conditions. This variable displacement pump changes the positions of the ring as a function of the boundary conditions.

Recently, it has been worth pointing out the relevance of alternative fuels in the improvement of air quality conditions and in the mitigation of global warming. In order to deal with these demands, in recent studies, it has been considered a great variety of alternative fuels. It goes without saying that the alternative fuels industry needs the best of the efficiency with a moderate layout. From this perspective, Liquefied Petroleum Gas (LPG) could represent a valid option, although it is not a renewable fuel. In terms of polluting emissions, the LPG can reduce nitrous oxides and smoke concentrations in the air, a capability that has a relevant importance for the modern pollution legislation. LPG is well known as an alternative fuel for Spark Ignition (SI) engines and, more recently, LPG systems have also been introduced in the Compression Ignition (CI) engines in dual-fuel configuration.