Search Results

Selective Catalytic Reduction (SCR) diesel exhaust aftertreatment systems are virtually indispensable to meet NOx emissions limits worldwide. These systems generate the NH3 reductant by injecting aqueous urea solution (AUS-32/AdBlue®/DEF) into the exhaust for the SCR NOx reduction reactions. Understanding the AUS-32 injector spray performance is critical to proper optimization of the SCR system. Specifically, better knowledge is required of urea sprays under operating conditions including those where fluid temperatures exceed the atmospheric fluid boiling point. Results were previously presented from imaging of an AUS-32 injector spray which showed substantial structural differences in the spray between room temperature fluid conditions, and conditions where the fluid temperature approached and exceeded 104° C and “flash boiling” of the fluid was initiated.

In the present paper an innovative approach for the shot-to-shot hydraulic characterization of low pressure injection systems is experimentally assessed. The proposed methodology is an inverse application of the Zeuch’s method, which in this case is applied to a closed volume upstream the injector instead of downstream of it as in conventional injection analyzers. By this approach, the well-known constraint of having a finite volume pressurized with the injected liquid downstream the injector is circumvented. As a consequence, with the proposed instrument low pressure injectors - such as PFI, fed with gasoline or water, SCR injectors - can operate with the prescribed upstream-downstream pressure differential. Further, the injector can spray directly in atmosphere or in any ambient at arbitrary pressure and temperature conditions, allowing the simultaneous application of other diagnostics such as imaging, momentum flux measurement or sizing instruments.

The present paper describes the effect of thermal conditions on the hydraulic behavior of Diesel common rail injectors, with a particular focus on low temperatures for fuel and injector body. The actual injection system thermal state can significantly influence both the injected quantity and the injection shape, requiring proper amendments to the base engine calibration in order to preserve the combustion efficiency and pollutant emissions levels. In particular, the introduction of the RDE (Real Driving Emission) test cycle widens the effective ambient temperature range for the homologation cycle, this way stressing the importance of the thermal effects analysis. An experimental test bench was developed in order to characterize the injector in an engine-like configuration, i.e. fuel pump, piping, common rail, pressure control system and injectors.

In the current automotive scenario, particulate filter technology is mandatory in order to attain emission limits in terms of particulate matter for diesel engines. Despite the fact that the Diesel Particulate Filter (DPF) is often considered a mature technology, significant issues can result from the use of the engine fuel injectors to introduce into the exhaust pipe the fuel needed to ignite the particulate matter accumulated in the filter during its regeneration. The most important issue is lubricant oil dilution with fuel as a consequence of significant spray impact on the cylinder liner. As an alternative, the fuel required to start DPF regeneration can be introduced in the exhaust pipe by an auxiliary low-pressure injector spraying in the hot exhaust gas stream.

One of the favored automotive exhaust aftertreatment solutions used for nitrogen oxides (NOx) emissions reductions is referred to as Selective Catalytic Reduction (SCR), which comprises a catalyst that facilitates the reactions of ammonia (NH3) with the exhaust nitrogen oxides (NOx). It is customary with these systems to generate the NH3 by injecting a liquid aqueous urea solution (AUS-32) into the exhaust. The urea solution is injected into the exhaust and transformed to NH3 by various mechanisms for the SCR reactions. Understanding the spray performance of the AUS-32 injector is critical to proper optimization of the SCR injection system. Results were previously presented from imaging of an AUS-32 injector spray under hot exhaust conditions at the injector spray exit for an exhaust injection application.

Emission legislation for light and heavy duty vehicles is requiring a drastic reduction of exhaust pollutants from internal combustion engines (ICE). Achieving a quick heating-up of the catalyst is of paramount importance to cut down cold start emissions and meet current and new regulation requirements. This paper describes the development and the basic characteristics of a novel burner for diesel engines exhaust systems designed for being activated immediately at engine cold start or during vehicle cruise. The burner is comprised of a swirled fuel dosing system, an air system, and an ignition device. The main design characteristics are presented, with a detailed description of the atomization, air-fuel interaction and mixture formation processes. An atomizer prototype has been extensively analyzed and tested in various conditions, to characterize the resulting fuel spray under cold-start and ambient operating conditions.

A comprehensive experimental and numerical analysis of two state-of-the-art diesel AfterTreatment Systems (ATS) for automotive applications is presented in this work. Both systems, designed to fulfill Euro 6 emissions regulations standards, consist of a closed-coupled Diesel Oxidation Catalyst (DOC) followed by a Selective Catalytic Reduction (SCR) catalyst coated on a Diesel Particulate Filter (DPF), also known as SCR on Filter (SCRoF or SCRF). While the two systems feature the same Urea Water Solution (UWS) injector, major differences could be observed in the UWS mixing device, which is placed upstream of the SCRoF, whose design represents a crucial challenge due to the severe flow uniformity and compact packaging requirements.

Close-coupled aftertreatment systems (ATS) for automotive Diesel engines composed of DOC and SCR offer a significant potential in terms of pollutant emission control capability even with the introduction of more aggressive driving cycles and rigorous limits for type-approval tests. This is particularly important for incoming certification standards where the forecast is showing a trade-off towards ultra-low NOx emissions values. As the SCR system NOx conversion capability largely relies on both the UWS mixing device and on NOx sensors used to detect the actual NH3 slip and residual NOx concentration, developing numerical simulation tools for the analysis of the actual flow pattern and species concentration over peculiar sections of the exhaust system is crucial to support the ATS development process.

The use of hydrogen in internal combustion engines is an effective approach to significantly support the reduction of CO2 emissions from the transportation sector using technically affordable solutions. The use of direct injection is the most promising approach to fully exploit hydrogen potential as a clean fuel, while preserving targets in terms of power density and emissions. In this frame, the development of an effective combustion system largely relies on the hydrogen-air mixture formation process, so to adequately control the charge stratification to mitigate pre-ignitions and knock and to minimize NOx formation. Hence, improving capabilities of designing a correct gas jet-air interaction is of paramount importance. In this paper the analysis of the evolution of a high-pressure gas jet produced by a single-hole prototype injector operated with different pressure ratios is presented.