Search Results

Fuel consumption of vehicles has received increased attention in recent years; however one neglected area that can have a large effect on this is the energy usage for the interior climate. This study aims to investigate the energy usage for the interior climate for different conditions by measurements on a complete vehicle. Twelve different NEDC tests in different temperatures and thermal states of the vehicle were completed in a climatic wind tunnel. Furthermore one temperature sweep from 43° to −18°C was also performed. The measurements focused on the heat flow of the air, from its sources, to its sink, i.e. compartment. In addition the electrical and mechanical loads of the climate system were included. The different sources of heating and cooling were, for the tested powertrain, waste heat from the engine, a fuel operated heater, heat pickup of the air, evaporator cooling and cooling from recirculation.

It is well known that wheels are responsible for a significant amount of the total aerodynamic drag of passenger vehicles. Tyres, and mostly rims, have been the subject of research in the automotive industry for the past years, but their effect and interaction with each other and with the car exterior is still not completely understood. This paper focuses on the use of CFD to study the effects of tyre geometry (tyre profile and tyre tread) on road vehicle aerodynamics. Whenever possible, results of the numerical computations are compared with experiments. More than sixty configurations were simulated. These simulations combined different tyre profiles, treads, rim designs and spoke orientation on two car types: a sedan and a sports wagon. Two tyre geometries were obtained directly from the tyre manufacturer, while a third geometry was obtained from our database and represents a generic tyre which covers different profiles of a given tyre size.

Passenger car fuel consumption is a constant concern for automotive companies and the contribution to fuel consumption from aerodynamics is well known. Several studies have been published on the aerodynamics of wheels. One area of wheel aerodynamics discussed in some of these earlier works is the so-called ventilation resistance. This study investigates ventilation resistance on a number of 17 inch rims, in the Volvo Cars Aerodynamic Wind Tunnel. The ventilation resistance was measured using a custom-built suspension with a tractive force measurement system installed in the Wheel Drive Units (WDUs). The study aims at identifying wheel design factors that have significant effect on the ventilation resistance for the investigated wheel size. The results show that it was possible to measure similar power requirements to rotate the wheels as was found in previous works.

Targets for reducing emissions and improving energy efficiency present the automotive industry with many challenges. Passenger cars are by far the most common means of personal transport in the developed part of the world, and energy consumption related to personal transportation is predicted to increase significantly in the coming decades. Improved aerodynamic performance of passenger cars will be one of many important areas which will occupy engineers and researchers for the foreseeable future. The significance of wheels and wheel housings is well known today, but the relative importance of the different components has still not been fully investigated. A number of investigations highlighting the importance of proper ground simulation have been published, and recently a number of studies on improved aerodynamic design of the wheel have been presented as well. This study is an investigation of aerodynamic influences of different tires.

Car accident investigations have shown that the head, the chest and the abdomen are the three most vulnerable body regions in side impacts, when serious-to-fatal (MAIS 3-6) injuries are considered. Injuries are much more common to occupants seated on the struck side than to those on the non-struck side. The development of new side impact protection systems has therefore been focused on struck side occupants. The first airbag system for side impact protection, jointly developed by Volvo and Autoliv, was introduced on the market in 1994. The SIPS bag is seat-mounted and protects mainly the chest and the abdomen, and also to some extent the head, since the head's lateral relative displacement is reduced by the side airbag, thereby keeping the head inside the car's outer profile. However, if an external object is exposed in the head area, for example in a truck-to-car side impact or in a single car collision into a pole or a tree, there is a need for an additional head protection device.

During the development of the aerodynamic properties of fore coming road vehicles down scaled models are often used in the initial phase. However, if scale models are to be utilised even further in the aerodynamic development they have to include geometrical representatives of most of the components found in the real vehicle. As the cooling package is one of the biggest single generators of aerodynamic drag the heat exchangers are essential to include in a wind tunnel model. However, due mainly to limitations in manufacturing techniques it is complicated to make a down scaled heat exchanger and instead functional dummy heat exchangers have to be developed for scaled wind tunnel models. In this work a Computational Fluid Dynamics (CFD) code has been used to show that it is important that the simplified heat exchanger model has to be of comparable size to that of the full scale unit.

The airflow around a detailed car underbody has been simulated using a commercial CFD software. Moving ground and rotating-wheel boundary conditions were applied in order to allow comparisons of Cd and dCd values with experimental data from a wind tunnel fitted with moving ground facilities. The calculated Cd and dCd figures compared very well with the available experimental results. Four configurations were tested and the maximum difference between experimental and numerical Cd values was 0.009. The individual contribution of different parts of the vehicle to the total drag was calculated and is discussed in this paper. This paper also describes in detail the numerical technique used to perform the computations.

In the early days of the automotive industry, durability and reliability were hit or miss affairs, with end-users often being the first to know about any durability problems - and in many cases forming an essential part of the development process. More recently, automotive companies have developed proving ground and laboratory test procedures that aim to simulate typical or severe customer usage. These test procedures have been used to develop the products through a series of prototypes and to prove the durability of the product prior to release in the marketplace. Now, commercial pressures and legal requirements have led to increasing reliance on CAE methods, with fatigue life prediction having a central role in the durability engineering process.

Driver errors cause a majority of all car accidents. Forward collision avoidance systems aim at avoiding, or at least mitigating, host vehicle frontal collisions, of which rear-end collisions are one of the most common. This is done by either warning the driver or braking or steering away, respectively, where each action requires its own considerations and design. We here focus on forward collision by braking, and present a general method for calculating the risk for collision. A brake maneuver is activated to mitigate the accident when the probability of collision is one, taking all driver actions into considerations. We describe results from a simulation study using a large number of scenarios, created from extensive accident statistics. We also show some results from an implementation of a forward collision avoidance system in a Volvo V70. The system has been tested in real traffic, and in collision scenarios (with an inflatable car) showing promising results.

There are now several wind tunnel facilities within Europe for testing passenger cars with and without moving ground and rotating wheel conditions (henceforth abbreviated to MVG&RW conditions). Within these facilities, the drag of a car under MVG&RW conditions is typically less than the drag of a car under stationary ground and stationary wheel conditions. This drag difference has been found to vary from a decrease of about 25 drag counts to a small drag increase according to published sources. A drag reduction of 10 to 20 drag counts is more typical, however.

Numerical and modeling errors in computational aerodynamics consist of multiple components. Previous investigations at Volvo have shown that low Reynolds k-ε models generally give better levels in pressure over the rear base area of the car than the corresponding wall function based model. However, these computations were carried out on car shapes without wheels. This paper presents numerical simulations of the flow field around three versions of the Volvo validation car series (VRAK). The geometry is a typical car with flat floor and simplified tires. The three car models differ by their rear shape. The configurations are: one with a nearly flat base, a fastback with a sloping rear window, and a car with a roof wing. The influence of the near wall formulation of the standard k-ε model on drag and lift is investigated. The performance of the low Reynolds number version of the cubic k-ε model by Suga [7] is also investigated.

Existing battery parameter model structures are evaluated by estimating model parameters on real driving data applying standard system identification methods. Models are then evaluated on the test data in terms of goodness of fit and RMSE in voltage predictions. This is different from previous battery model evaluations where a common approach is to train parameters using standardized tests, e.g. hybrid pulse-power capability (HPPC), with predetermined charge and discharge sequences. Equivalent linear circuit models of different complexity were tested and evaluated in order to identify parameter dependencies at different state of charge levels and temperatures. Models are then used to create voltage output given a current, state of charge and temperature. The average accuracy of modelling the DC bus voltage provides a model goodness of fit average higher than 90% for a single RC circuit model.

This paper presents an experimental study of aeroacoustical sound sources generated by the turbulent flow around the side mirror of a Volvo V70. Measurements were carried out at the Volvo Cars aerodynamical wind tunnel (PVT) and at the aeroacoustical wind tunnel of Stuttgart University (FKFS). Several different measurement techniques were applied in both tunnels and the results were compared to each other. The configurations considered here were: side mirror with a cord and without the cord. The results discussed in this paper include intensity probe measurements in the flow around the side mirror, sound source localization with beamforming technique using a three-dimensional spherical array as well as standard measurements inside the car with an artificial head. This experimental study focused on understanding the differences between testing at the PVT and FKFS.

Vehicle dynamics development relies on subjective assessments (SA), which is a resource-intensive procedure requiring both expert drivers and vehicles. Furthermore, development projects becoming shorter and more complex, and increasing demands on quality require higher efficiency. Most research in this area has focused on moving from physical to virtual testing. However, SA remains the central method. Less attention has been given to provide better tools for the SA process itself. One promising approach is to introduce computer-tablets to aid data collection, which has proven to be useful in medical studies. Simple software solutions can eliminate the need to transcribe data and generate more flexible and better maintainable questionnaires. Tablets’ technical features envision promising enhancements of SA, which also enable better correlations to objective metrics, a requirement to improve CAE evaluations.

Maintaining the current ratio between certified and the customer-observed fuel consumption even with future required levels poses a considerable challenge. Increasing the efficiency of the driveline enables certified fuel consumption down to a feasible level in the order of 80 g CO₂/km using fossil fuels. Mainly affecting off-cycle fuel consumption, energy amounts used to create good interior climate as well as energy-consuming options and features threaten to further increase. Progressing urbanization will lead to decreasing average vehicle speeds and driving distances. Highly efficient powertrains come with decreased amounts of waste energy traditionally used for interior climate conditioning, thus making necessary a change of auxiliary systems.

The aim of this method is to measure emissions from components in the fuel system in a way that is comparable with regulated measurements by Sealed Housing for Evaporative Determination (SHED). In a circuit, constructed as a differential reactor, air is circulated between a test cell and a flame ionization detector (FID) for total hydrocarbon measurement. A test object, i.e. a fuel system component, is filled with fuel and placed in a sealed test cell. Due to the flow characteristic, equilibrium will occur between the air and the fuel evaporated from the surface of the test object. The amount of air consumed in the reactor is compensated by pure air being added to the system. The concentration of hydrocarbon in the circulated air is continuously measured by the FID.

Many accidents are road departures because of the drivers' lack of attention. This is in many cases due to distraction, drowsiness or intoxication. The Haptic Lane Departure Warning System described here is intended as an active safety system, thus aiming at decreasing the amount of unwanted lane departures. The challenge in the development of such kinds of functions lies in the determination of dangerous situations and the design of appropriate warning/intervention strategies. The system is intended to go unnoticed with the driver and intervenes only in instances where the driver mismanages steering control. Unlike systems which issue an audible sound, the type of warning is a tactile feedback via the steering wheel. This torque is designed in a way that it communicates to the driver the appropriate steering wheel angle required in order to come back in lane.

With the increase in fuel prices and the increasingly strict environmental legislations regarding CO₂ emissions, reduction of the total energy consumption of our society becomes more important. Passenger vehicles are partly responsible for this consumption due to their strong presence in the daily life of most people. Therefore reducing the impact of cars on the environment can assist in decreasing the overall energy consumption. Even though several fields have an impact on a passenger car's performance, this paper will focus on the aerodynamic part and more specifically, the wake behind a vehicle. By definition a car is a bluff body on which the air resistance is for the most part driven by pressure drag. This is caused by the wake these bodies create. Therefore analyzing the wake characteristics behind a vehicle is crucial if one would like to reduce drag.

The objective of this paper is to investigate whether different appearance modes of the digital human models (DHM or manikins) affect the observers when judging a working posture. A case where the manikin is manually assembling a battery in the boot with help of a lifting device is used in the experiment. 16 different pictures were created and presented for the subjects. All pictures have the same background, but include a unique posture and manikin appearance combination. Four postures and four manikin appearances were used. The subjects were asked to rank the pictures after ergonomic assessment based on posture of the manikin. Subjects taking part in the study were either manufacturing engineering managers, simulation engineers or ergonomists. Results show that the different appearance modes affect the ergonomic judgment. A more realistic looking manikin is rated higher than the very same posture visualized with a less natural appearance.

One way of avoiding crashes or mitigating the consequences of a crash is to apply an autonomous braking system. Quantifying the benefit of such a system in terms of injury reduction is a challenge. At the same time it is a fundamental input into the vehicle development process. This paper describes a method to estimate the effectiveness of reducing speed prior to impact. A holistic view of quantifying the benefit is presented, based on existing real life crash data and basic dynamic theories. It involves a systematic and new way of examining accident data in order to extract information concerning pre-crash situations. One problem area when implementing collision mitigation systems is being able to achieve sufficient target discrimination. The results from the case study highlight frontal impact situations from real world accident data that have the greatest potential in terms of improving accident outcome.