Search Results

The performance of an organic Rankine cycle (ORC) that recovers heat from the exhaust of a heavy-duty diesel engine was simulated. The work was an extension of a prior study that simulated the performance of an experimental ORC system developed and tested at Oak Ridge National laboratory (ORNL). The experimental data were used to set model parameters and validate the results of that simulation. For the current study the model was adapted to consider a 15 liter turbocharged engine versus the original 1.9 liter light-duty automotive turbodiesel studied by ORNL. Exhaust flow rate and temperature data for the heavy-duty engine were obtained from Southwest Research Institute (SwRI) for a range of steady-state engine speeds and loads without EGR. Because of the considerably higher exhaust gas flow rates of the heavy-duty engine, relative to the engine tested by ORNL, a different heat exchanger type was considered in order to keep exhaust pressure drop within practical bounds.

Correct shifting schedule of vehicle coasting mode play a vital role in improving vehicle comfort and economy. At present, the calibration of the transmission shifting schedule ignores the impact of vehicle’s dynamic mass. This paper proposes a method for optimizing the shifting schedule of the coasting modes with gear based on the dynamic mass identification of the vehicle. This method identifies the dynamic mass of the vehicle during driving and substitute them into the process of solving the shifting schedule parameters. Then we get the optimal shifting schedule. At first, establish the Extended Kalman Filter to Pre-process the experimental data, reducing errors caused by excessive data fluctuations. Then, establishing a weighted squares estimation model based on particle swarm optimization to identify the dynamic mass of the vehicle.

With the rapidly developing automotive industry and stricter environmental protection laws and regulations, lightweight materials, advanced manufacturing processes and structural optimization methods are widely used in body design. Therefore, in order to evaluate and improve the pedestrian protection during a collision, this paper presents an impact simulation modeling and structural optimization method for a sport utility vehicle engine hood made of carbon fiber reinforced plastic (CFRP). Head injury criterion (HIC) was used to evaluate the performance of the hood in this regard. The inner panel and the outer panel of CFRP hood were discretized by shell elements in LS_DYNA. The Mat54-55 card was used to define the mechanical properties of the CFRP hood. In order to reduce the computational costs, just the parts contacted with the hood were modeled. The simulations were done in the prescribed 30 impact points.

Gradient based topology optimization method is difficult used to optimization of crashworthiness structures due to the expensive computational cost of sensitivity analysis and complex nonlinear behaviors (geometric nonlinearity, material nonlinearity and contact nonlinearity) of structures during a collision. Equivalent static loads (ESLs) method is one of the methods for nonlinear dynamic response optimization. However, this method ignores the material nonlinearity. Thus this paper proposes an improved topology optimization method for crashworthiness structure based on a modified ESLs method. A new calculation of ESLs considering material nonlinearity is proposed. The improved ESLs method is employed to transform the nonlinear dynamic response optimization into a nonlinear static response optimization with multiple load cases. Each element in the design domain is assigned with a design variable.

With the increase of car ownership and the complex and crowded parking environment, it is difficult for drivers to complete the parking operation quickly and accurately, which may cause traffic accidents such as vehicle collisions and road jams because of poor parking skills. The emergence of an automatic parking system can help drivers park safely and reduce the occurrence of safety accidents. In this paper, the neural network identifier on the control method of an adaptive integral derivative of a neural network is proposed for an automatic parallel parking system with front-wheel steering is studied by using MATLAB/Simulink environment, and the simulation is carried out. Firstly, according to vehicle parameters and obstacle avoidance constraints, the minimum parking space, and parking starting position are calculated. Meanwhile, the path planning of parallel parking spaces is carried out by quintic polynomial.

Based on the multi-body system, the work research the injury index of the mathematics models of pedestrian, by simulating the motion of the pedestrian impacted by vehicle using MADYMO. Compared with the article published, verify the dependability of this simulated test. Based on the dependability, Carry on sensitivity analysis to design parameter of the automobile. Research on the pedestrian protection by the vehicle by revising the sensitive design parameter. By simulating the pedestrian impacted by the vehicle which installing the hood raise structure, search on the injury index. Compared with the original injury index, we can find that the hood raise structure be propitious to the pedestrian.

The closed cabin temperature is anticipated to be cooled down when it is a bit hot inside the driving car. The traditional air-condition lowers the cabin temperature by frequently switching the status of the compressor, which increases the engine’s parasitic power and shortens the compressor’s service-life. The semiconductor auxiliary cooling system with the properties of no moving parts, high control precision and quick response has the potential to assist the on-board air-condition in modulating the cabin temperature with relative small ranges. Little temperature differences between the cabin and the outside environment means that the system energy consumption to ensure the occupant comfort is relatively low and the inefficiency could be made up by the renewable energy source.

The mountainous roads are rugged and complex, so that the driver can not make accurate judgments on dangerous road conditions. In addition, most heavy vehicles have characteristics of large weight and high center of gravity. The two factors above have caused most of the car accidents in mountain areas. A research shows that 90% of car accidents can be avoided if drivers can respond within 2-3 seconds before the accidents happen. This paper proposes a speed warning scheme for heavy-duty vehicle over the horizon in mountainous area, which can give the drivers enough time to respond to the danger. In the early warning aspect, this system combines the front road information, the vehicle characteristics and real-time information obtained from the vehicle, calculates and forecasts the danger that may happen over the horizon ahead of time, and prompts the driver to control the vehicle speed.

In order to overcome hysteresis and dead zone problems caused by friction for the proportional solenoid valve, and improve rapidity and stability of the pneumatic system on hydraulic retarder, a closed-loop control strategy based on valve coil current was proposed. The high-frequency low-amplitude dither signal was introduced into the proportional solenoid valve. With the proper dither signal, the stick-slip motion of the valve core was transformed into a steady one, and its dynamic performance was improved. Consequently, response time of retarder was reduced during gear changing. The proportional valve coil current was measured as a feedback for a closed-loop control strategy. Combining with the closed-loop strategy, the PI control algorithm was adopted to make sure that valve current was in accordance with the target value. Pulse Width Modulation (PWM) signal was used for the driving of proportional solenoid valve.

Several factors including internal factors which are related to the structure and components of transmission and external factors which are related to the running condition influence transmission efficiency (TE) collectively. Selected one manual transmission as the research object, this paper mainly analyzes factors including gears and bearings power loss through theoretical calculation and the external factors, such as gears, temperature and torque. Firstly, with a methodology, the overall efficiency of the manual transmission is calculated based on factors. Then, this paper discusses efficiency through external factor. This transmission is experimented on transmission test bench. On the bench, the driving motor (DM) simulates the power input of engine and the load motor (LM) simulates the whole resistance of vehicle. The mechanical transmission is operating in different speeds, torques and work temperature, thus the corresponding data are obtained.

Glass lifter is a key part of automobile door system. Guide rail is the carrier of glass lifter, and it bears various load cases when glass lifer works. Mass, stiffness and natural frequencies are the factors that influence the performance of glass lifter. In order to design a lighter and reasonable glass lifter, topology optimization methods are studied in this paper. In a rope-wheel glass lifter, design domain is determined by the mechanical structure and working conditions. Firstly, the single target continuum structure topology optimization mathematic models of guide rail are built in this paper, and analysis of multi-stiffness topology optimization are carried out accordingly in which volume fraction is set as 0.4, 0.5 and 0.6. These models are based on SIMP (Solid Isotropic Material with Penalization) theory.

As a key component of airstream system equipped in the road sweeper, the structure of the suction nozzle determines its internal flow field distribution, which affects the dust-sucking efficiency to a great degree. This research is aiming to determine a better suction nozzle structure. Starting with an analysis of the one used in a certain type of road sweeper, the initial model of the suction nozzle is established, and the internal flow field is simulated with typical computational fluid dynamics (CFD) software named FLUENT. Based on the simulation results, the dust-sucking capability of the initial structure is evaluated from the aspects of pressure and velocity distribution. Furthermore, in order to explore the influence of different structural parameters on the flow field distribution within the suction nozzle, models with different cavity heights and shoulder angles are established, and Univariate Method is utilized to analyze the contrast models.

When vehicle traveling on the bumpy road or vehicle acceleration and deceleration, which will cause the body vibration of vehicle, at the same time, a large part of energy would be absorbed by the shock absorber transforms the mechanical energy into heat energy dissipated. In order to recycle the energy of vibration and keep the stability of running car, this paper provides the shock absorber of energy recovery that recycling the energy dissipated from the traditional absorber. The shock absorber includes rod and rodless chamber cavity, the two parts contain oil outlet and oil inlet, which connected to a bridge type loop of hydraulic to make pulsating oil pressure towards one direction, when the shock absorber vibration causes pulsating oil pressure, it drives hydraulic pump operation. Because the output shaft of the hydraulic pump fixedly attached to the input shaft of generator, so the generator produces electricity for recycling energy[1].

Dangerous driving behavior will cause serious traffic accidents, which will not only threaten life and property but also cause traffic congestion and reduce road capacity. Speed detection is an important detection method to identify whether a driver is driving dangerously. Traditional speed detection methods need additional sensors, which will increase the cost of speed measurement. This paper proposes a vehicle speed estimation algorithm based on the imaginary projection plane (IPP). The IPP will be established according to the height, field angle, and vertical tilt angle of the camera and will be used to establish the mapping relationship between the world coordinates and image coordinates of the vehicle. By combining YOLOv4 and DeepSORT, the vehicle license plate is detected and tracked, and the center point of the vehicle license plate is taken as the feature point of vehicle speed estimation. The vehicle speed is estimated according to the IPP.

The development of electrification is widely considered to be the key to the transportation industry. In recent years, the number of electric trucks on the road is increasing year by year, so the safety of electric trucks is of great importance. At present, the batteries of electric trucks are mostly arranged on the two sides of the trucks. The protective devices are only the guardrails fixed on the vehicle body, so the protective effect is poor. In view of this situation, this paper designed a battery protection device for electric truck. When the truck is hit in a side collision, the transverse guardrail first generates plastic deformation and absorbs kinetic energy. At this time, the collision force is transmitted to the energy-absorbing box along the moving direction of the side collision vehicle, and the energy-absorbing box is contracted to produce a buffer effect.

Road traffic accidents resulting from alcohol-impaired driving are increasing globally despite several measures, currently in place, to curb the trend. For this reason, recent research aims at integrating alcohol early-detection systems and driving simulator experiments to identify intoxicated drivers. However, driving simulator experiments on drunk driving have focused mostly on male participants than female drivers whose characteristics have scarcely been explored. Hence in this paper, vehicle dynamic control inputs on steering, braking, and acceleration performance of 75 licensed female drivers with an upshot of alcohol at four different blood alcohol concentration (BAC) levels (0%, 0.03%, 0.05%, and 0.08%) were investigated. The participants completed simulated driving in a fixed-based simulator experiment coupled with real-time ecological scenarios to extract discrete responses.

The tank truck has a wide range of application. When the liquid in the tank is not fully loaded, the lateral movement of the liquid in the tank will shift the center of gravity of the tank truck and make the vehicle less safe. It is easy to roll over when the tank truck is turning. This study combines the vehicle dynamic characteristics and geographic information, which gives the driver safe speed and safe braking distance tips before turning, to reduce the traffic accidents caused by driver's misjudgment. The dynamic model of the tank truck is established, through collecting the real-time information of the vehicle, the vehicle load and braking torque are calculated by the relevant dynamic model. The system needs to measure the deviation of the center of gravity in the tank truck movement process, and the deviation of the center of gravity has a great influence on the safety speed.

The development of high precision flow divider/combiner valves has received considerable attention by the authors over the past decade. Several different valve designs for division and combination of flow have been designed which display small flow dividing/combining error (1-2%) when compared to conventional designs (2-10%). Recent studies have improved upon the design in order to reduce cost, weight and complexity of the valve. This paper will present the latest of the authors research into the development of a high precision, autoregulated flow divider/combiner valve with an integral shuttle valve. The autoregulator extends the operating range of the integrated flow divider/combiner valve (for errors less than 2 %) to 10-50 lpm compared to 30-50 lpm for the unregulated valve.

A flow divider valve is a device which allows a single stream of fluid to be split into two paths according to a predetermined ratio and independent of variations or differences in the load pressures. A flow combiner valve combines two paths of fluid into one stream such that the ratio of the flow rates coming into the valve remains independent of any variation or difference between the inlet pressures. This paper describes the design, operation and performance of an integrated flow divider/combiner valve. This design maintains the small flow dividing/combining error of high precision valves (less than 1.5% at rated flow) but incorporates the shuttle valve into the main spool system. This new design reduces the weight of the valve by 20% reducing the cost by approximately 10%. The new structure simplifies the construction of high precision valves and reduces a source of flow dividing/combining error (leakage).

According to the requirements of high transmission ratio and high load torque of high-speed electric drive axle planetary gear system, the design and analysis of fine-pitch planetary gear system with small modulus, small pressure angle and high full tooth height of are carried out. In order to improve the bearing capacity of gear and reduce gear meshing noise, the tooth profile modification parameters of gear system are optimized. In this paper, the tooth modification methods are analyzed and the gear train parameters are determined. The influence degree of different tooth modification methods on the transmission performance of the gear train is determined by orthogonal experiment method. The transmission error is reduced, the stress fluctuation is improved, and the gear meshing performance is greatly improved by adopting the appropriate modification scheme, which proves the effectiveness of the tooth modification scheme.