Search Results

Real-time simulation of truck and trailer combinations can be applied to hardware-in-the-loop (HIL) systems for developing and testing electronic control units (ECUs). The large number of configuration variations in vehicle and axle types requires the simulation model to be adjustable in a wide range. This paper presents a modular multibody approach for the vehicle dynamics simulation of single track configurations and truck-and-trailer combinations. The equations of motion are expressed by a new formula which is a combination of Jourdain's principle and the articulated body algorithm. With the proposed algorithm, a robust model is achieved that is numerically stable even at handling limits. Moreover, the presented approach is suitable for modular modeling and has been successfully implemented as a basis for various system definitions. As a result, only one simulation model is needed for a large variety of track and trailer types.

Advanced driver assistance systems (ADAS) are becoming increasingly important for today's commercial vehicles. It is therefore crucial that different ADAS functionalities interact seamlessly with existing electronic control unit (ECU) networks. For example, autonomous emergency braking (AEB) systems directly influence the brake ECU and engine control. It has already become impossible to reliably validate this growing interconnectedness of control interventions in vehicle behavior with prototype vehicles alone. The relevant tests must be brought into the lab at an earlier development stage to evaluate ECU interaction automatically. This paper presents an approach for using hardware-in-the-loop (HIL) simulation to validate ECU networks for extremely diverse ADAS scenarios, while taking into account real sensor data. In a laboratory environment, the sensor systems based on radars, cameras, and maps are stimulated realistically with a combination of simulation and animation.

The complexity of automobile powertrains grows continuously. At the same time, development time and budget are limited. Shifting development tasks to earlier phases (frontloading) increases the efficiency by utilizing test benches instead of prototype vehicles (road-to-rig approach). Early system verification of powertrain components requires a closed-loop coupling to real-time simulation models, comparable to hardware-in-the-loop testing (HiL). The international research project Advanced Co-Simulation Open System Architecture (ACOSAR) has the goal to develop a non-proprietary communication architecture between real-time and non-real-time systems in order to speed up the commissioning process and to decrease the monetary effort for testing and validation. One major outcome will be a generic interface for coupling different simulation tools and real-time systems (e.g. HiL simulators or test benches).

In the aerospace industry, methods for virtual testing cover an increasing range of test executions carried out during the development and test process of avionics systems. Over the last years, most companies have focused on questions regarding the evaluation and implementation of methods for virtual testing. However, it has become more and more important to seamlessly integrate virtual testing into the overall development process. For instance, a company’s test strategy might stipulate a combination of different methods, such as SIL and HIL simulation, in order to benefit from the advantages of both in the same test process. In this case, efforts concentrate on the optimization of the overall process, from test specification to test execution, as well as the test result evaluation and its alignment with methods for virtual testing.

Real-time simulation of truck and trailer combinations can be applied to hardware-in-the-loop (HIL) systems for developing and testing electronic control units (ECUs). The large number of configuration variations in vehicle and axle types requires the simulation model to be adjustable in a wide range. This paper presents a modular multibody approach for the vehicle dynamics simulation of single track configurations and truck-and-trailer combinations. The equations of motion are expressed by a new formula which is a combination of Jourdain's principle and the articulated body algorithm. With the proposed algorithm, a robust model is achieved that is numerically stable even at handling limits. Moreover, the presented approach is suitable for modular modeling and has been successfully implemented as a basis for various system definitions. As a result, only one simulation model is needed for a large variety of track and trailer types.

The application of a communication infrastructure for hybrid test systems is currently a topic in the aerospace industry, as also in other industries. One main reason is flexibility. Future laboratory tests means (LTMs) need to be easier to exchange and reuse than they are today. They may originate from different suppliers and parts of them may need to fulfill special requirements and thus be based on dedicated technologies. The desired exchangeability needs to be achieved although suppliers employ different technologies with regard to specific needs. To achieve interoperability, a standardized transport mechanism between test systems is required. Designing such a mechanism poses a challenge as there are several different types of data that have to be exchanged. Simulation data is a prominent example. It has to be handled differently than control data, for example. No one technique or technology fits perfectly for all types of data.

A chemical sub-model for realistic CFD simulations of Diesel engines is developed and demonstrated by application to some test cases. The model uses a newly developed progress variable approach to incorporate a realistic treatment of chemical reactions into the description of the reactive flow. The progress variable model is based on defining variables that represent the onset and temporal development of chemical reactions before and during self ignition, as well as the stage of the actual combustion. Fundamental aspects of the model, especially its physical motivation and finding a proper progress variable, are discussed, as well as issues of practical implementation. Sample calculations of Diesel-typical combustion scenarios are presented which are based on the progress-variable model, showing the capability of the model to realistically describe the ignition-and combustion phase.

The main objective of engine 3D CFD simulation is nowadays the support for combustion design development. New combustion concepts (e.g. Low Temperature Combustion, HCCI, multiple injection strategies …) could be analyzed and predicted through detailed thermodynamical computation. To achieve this aim many simulation tools are needed: each of them has to be capable to reproduce the sensitivities of combustion design parameters through physically based models. The adopted approach consists of the coupling of different models for 3D-nozzle flow, orifice-resolved spray formation in Eulerian coordinates and combustion. The advantages of the method will be proofed on an operative DI-diesel truck engine case, run with different nozzle geometries.

This paper will first introduce and classify the basic principles of architecture-driven software development and will briefly sketch the presumed development process. This background information is then used to explain extensions which enable current behavior modeling and code generation tools to operate as software component generators. The generation of AUTOSAR software components using dSPACE's production code generator TargetLink is described as an example.

Investigations of the aerodynamic influence of rotating wheels on a simplified vehicle model as well as on a series production car are presented. For this research CFD simulations are used together with wind tunnel measurements like LDV and aerodynamic forces. Several wheel rim geometries are examined in stationary and in rotating condition. A good agreement could be achieved between CFD simulations and wind tunnel measurements. Based on the CFD analysis the major aerodynamic mechanisms at rotating wheels are characterized. The flow topology around the wheels in a wheel arch is revealed. It is shown, that the reduction of drag and lift caused by the wheel rotation on the isolated wheel and the wheel in the wheel arch are based on different effects of the airflow. Though the forces decrease at the front wheel due to the wheel rotation locally, the major change in drag and lift happens directly on the automotive body itself.

Today, hardware-in-the-loop (HIL) simulation is common practice as a testing methodology for electronic control units (ECUs). An essential criterion for the efficiency of an HIL system is the availability of powerful test automation having access to all of its hardware and software components (including I/O channels, failure insertion units, bus communication controllers and diagnostic interfaces). The growing complexity of vehicle embedded systems, which are interconnected by bus systems (like CAN, LIN or FlexRay), result in hundreds or even thousands of tests that have to be done to ensure the correct system functionality. This is best achieved by automated testing. Automated testing usually is performed by executing tests on a standard PC, which is interconnected to the HIL system. However, higher demands regarding timing precision are hard to accomplish. As an example, ECU interaction has to be captured and responded to in the range of milliseconds.

Due to tougher legislation on exhaust emissions reduction and the consumer demand for more power and mobility and less fuel consumption, the functionality in today's engine management systems continues to grow. The electronic engine control units (ECUs) have to perform more control tasks using new sensors and actuators, along with the corresponding self-diagnostics (OBD, on-board diagnosis). All this leads to continuously increasing demands on automated hardware-in-the-loop (HIL) test systems. HIL technology has advanced in parallel to the ECUs, and is today an indispensable tool for developing automotive electronics. This paper therefore aims to provide a comprehensive and state-of-the-art survey of HIL test systems for engine controllers. First of all, a brief introduction to the ECU's functionality is given.

Electric drives are growing in importance in automotive applications, especially in hybrid electric vehicles (HEV) and in the vehicle dynamics area (steering systems, etc.). The challenges of real-time hardware-in-the-loop (HIL) simulation and testing of electric drives are addressed in this paper. In general, three different interface levels between the electric drive and the hardware-inthe-loop system can be distinguished: the signal level (1), the electrical level (2) and the mechanical level (3). These interface levels, as well as modeling and I/O-related aspects of electric drives and power electronics devices, are discussed in detail in the paper. Finally, different solutions based on dSPACE simulator technology are presented, for both hybrid vehicle and steering applications.

To fulfill future emission standards for diesel engines, combined after-treatment systems consisting of different catalyst technologies and diesel particulate filters (DPF) are necessary. For designing and optimizing the resulting systems of considerable complexity, effective simulation models of different catalyst and DPF technologies have been developed and integrated into a common simulation environment called ExACT (Exhaust After-treatment Components Toolbox). This publication focuses on a model for the NOx storage and reduction catalyst as a part of that simulation environment. A heterogeneous, spatially one-dimensional (1D), physically and chemically based mathematical model of the catalytic monolith has been developed. A global reaction kinetic approach has been chosen to describe reaction conversions on the washcoat. Reaction kinetic parameters have been evaluated from a series of laboratory experiments.

Validating control units with hardware-in-the-loop (HIL) simulators is an established method for quality enhancements in automotive software. It is primarily used for testing applications, but in view of increased networking between electronic control units, it can also be used for testing communication scenarios. The testing of electronic control unit (ECU) communication often includes only positive testing. Simple communication nodes are used for this, and communication analyzers are used for verifying communication up to the physical level. However, it is not only an ECU's positive communication behavior that has to be tested, but also its correct behavior in the event of communication errors. In HIL communication scenarios, it is not only possible to emulate the missing bus nodes (restbus simulation) with a link to real-time signals; correct ECU behavior in the event of communication errors can also be tested.

In modern vehicles the architecture of electronics is growing more and more complex because both the number of electronic functions – e.g. implemented as software modules – as well as the level of networking between electronic control units (ECUs) is steadily increasing. This complexity leads to greater propagation of failure symptoms, and diagnosing the causes of failure becomes a new challenge. Diagnostics aims at detecting failures such as defect sensors or faulty communication messages. It is subdivided into diagnosis algorithms on an ECU and algorithms running offboard, e.g. on a diagnostic tester. These algorithms have to complement each other in the best possible way. While in the past the diagnosis algorithm was developed late in the development process, nowadays there are efforts to start the development of such algorithms earlier – at least in parallel to developing a new feature itself. This would allow developers to verify the diagnosis algorithms in early design stages.

Model-based development and autocoding have become common practice in the automotive industry over the past few years. The industry is using these methods to tackle a situation in which complexity is constantly growing and development times are constantly decreasing, while the safety requirements for the software stay the same or even increase. The debate is no longer whether these methods are useful, but rather on the conditions for achieving optimum results with them. From the experiences made during the last decade this paper shows some of the key factors helping to achieve success when introducing or extending the deployment of automatic code generation in a model-based design process.

The integration of CAD/CAM/CAE in product development is the key to realize concurrent engineering. Generally, different systems are employed in product development department. These different systems create a lot of troubles such as difficult communication, misunderstanding and so on. A new approach to integrate CAD/CAM/CAE in one system based on CATIA for the end-to-end process in cylinder head development is presented. Multi-Model Technology (MMT) is used to create consistent and associated CAD models for the end-to-end process in cylinder head development. The concept and method to create and organize multi- models are discussed. A typically four-layer structure of MMT for mechanical products is defined. The multi-level structure of the cylinder head models based on MMT is provided. The CAD models of cylinder head created based on MMT can be used as the consistent model.

Hardware-in-the-loop (HIL) testing is used by commercial vehicle original equipment manufacturers (OEMs) in several fields of electronics development. HIL tests are a part of the standard development process for engine and machine control systems. For electronic control units (ECUs), not only the HIL test of the hardware but also the controller software validation is very important. For hardware diagnostics validation, a dynamic simulation of the real system could be omitted and an open-loop test of the controller is sufficient in most cases. For most controller software validation including OBD (on-board diagnosis) tests, detailed but real-time capable models have to be used. This article describes the needs and challenges of models in hardware-in-the-loop (HIL) based testing, taking into account the wide range of commercial and off-highway vehicles.

Hardware-in-the-loop (HIL) simulation in the development and test process of vehicle dynamics controllers requires a real-time tractor-trailer simulation model. The hitch coupling must be numerically stable to ensure real-time simulation for various driving maneuvers, particularly at the vehicle's handling limits. This paper presents a robust implementation of tractor-trailer coupling. The equation of motion is formed using a novel formulation which is a combination of Jourdain's Principle and the Articulated Body Algorithm. The paper shows that a robust model for a real-time tractor-trailer simulation can be achieved with the proposed method. Moreover, the approach presented is suitable for modular modeling, is successfully implemented and can also be used as a basis for flexible system definition with an adjustable number of trailer axles.