Refine Your Search

Date

Date

Topic

Topic

Vehicle occupants Design Engineering and Styling Noise, Vibration, and Harshness (NVH) Optics AGE-3 Aircraft Ground Support Equipment Committee Logistics Pressure

Search Results

Viewing 1 to 20 of 36
12Next >Last >>
Sort by relevance
Standard

CUSHION TOW HITCHES TEST
1974-05-01
HISTORICAL
AIR1353
The main purpose of this test was to determine the application advantages of cushion tow hitches in comparison to the commonly used rigid tow hitch type fitted on heavy aircraft towing tractors. As diverse opinions emerged about its suitability since the introduction on the market of this new tow hitch type, it was intended to physically measure and evaluate the damping capability of this cushioned tow link when applied in practice.
Standard

Method of Testing Pre-Conditioned Air Equipment
2021-04-08
CURRENT
ARP5374B
This SAE Aerospace Recommended Practice (ARP) applies to Point-Of-Use, Central and Mobile Pre-Conditioned Air Equipment. It does not apply to aircraft mounted equipment.
Standard

Method of Testing Pre-Conditioned Air Equipment
2008-04-15
HISTORICAL
ARP5374A
This SAE Aerospace Recommended Practice (ARP) applies to Point-Of-Use, Central and Mobile Pre-Conditioned Air Equipment. It does not apply to aircraft mounted equipment.
Standard

400-CYCLE GROUND POWER UNIT PROVISIONS FOR AIRCRAFT ELECTRICAL SYSTEM PROTECTION
2002-12-16
CURRENT
ARP760
This SAE Recommended Practice which defines the terms and tabulates the limits of the characteristics for various protective devices used in conjunction with 400-cycle ground power for civil aircraft is intended to assist the airlines in standardizing on 400-cycle protective systems. The limits found to be acceptable in the civil aircraft industry are presented.
Standard

Nose Gear Towbarless Tow Vehicle Basic Test Requirements
2005-02-10
HISTORICAL
ARP5283
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852A and ARP4853A. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, reduce the certified safe life limit of the nose gear, or induce a stability problem during pushback and/or maintenance towing operations. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only. It is not meant for dispatch (operational) towing (see definitions in Section 3). Dispatch towing imposes greater loads on nose gears and structure due to additional passenger, cargo, and fuel loads.
Standard

Nose Gear Towbarless Tow Vehicle Basic Test Requirements
2012-09-24
HISTORICAL
ARP5283A
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.
Standard

400 Hz Connection Aircraft Electrical Maintenance Procedures
2008-03-28
HISTORICAL
AIR4365A
This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.
Standard

400 Hz CONNECTION AIRCRAFT ELECTRICAL MAINTENANCE PROCEDURES
1994-12-01
HISTORICAL
AIR4365
This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.
Standard

Measurement of Exterior Sound Level of Specialized Aircraft Ground Support Equipment
2021-09-30
CURRENT
ARP1801A
The scope of this SAE Recommended Practice covers specialized internal combustion engine powered equipment used in support of aircraft operations. The equipment may be self-propelled, truck mounted, trailer mounted, skid mounted or stationary. It does not include construction equipment or equipment designed primarily for operation on highways or within factories or building areas. NOTE: Equivalent methodology is provided in (CEN) EN 1915-4, Aircraft ground support equipment - General requirements - Part 4: Noise measurement methods and reduction, to be used for measurements conforming to the EU Machinery Directive
Standard

Method of Evaluating Pneumatic Ground Power Units
2003-11-21
HISTORICAL
AIR4545
This SAE Aerospace Information Report (AIR) covers, and is restricted to, the behavior of air under conditions of critical and subcritical flow at temperatures less than 500 °F.
Standard

Design Specification for Regional Aircraft Towbarless Tow Vehicle for Pushback and/or Maintenance Towing Operations
2004-12-30
HISTORICAL
ARP5916
The tow vehicle should be designed for towbarless push-back and/or maintenance towing of regional type aircraft as specified in 1.3. The design will ensure that the unit will safely secure the aircraft nose landing gear within the coupling system for any operational mode. The purpose of this towing procedure is to achieve a safer and faster operation than is possible with conventional towing equipment.
Standard

Design Specification for Regional Aircraft Towbarless Tow Vehicle for Pushback and/or Maintenance Towing Operations
2022-03-28
CURRENT
ARP5916A
The tow vehicle should be designed for towbarless push-back and/or maintenance towing of regional type aircraft as specified in 1.3. The design will ensure that the unit will safely secure the aircraft nose landing gear within the coupling system for any operational mode. The purpose of this towing procedure is to achieve a safer and faster operation than is possible with conventional towing equipment.
Standard

Regional Aircraft Towbarless Tow Vehicle - Test Requirements
2022-03-30
CURRENT
ARP5911A
The present Aerospace Recommended Practice specifies for airplane operator and tow vehicle manufacturers the basic testing requirements for towbarless tow vehicles to be used on the nose gear of conventional tricycle type landing gears of commercial civil transport aircraft with maximum ramp weight between 8600 kg (19 000 lb) and 50 000 kg (110 000 lb), commonly designated as “regional aircraft”. Its purpose is to achieve testing results, or equivalent computer modeling, demonstrating that the loads induced by the tow vehicle will not exceed the design loads of the airplane’s nose landing gear and associated structure, reduce the certified safe life limit of the nose landing gear, or otherwise compromise the airplane’s structural integrity and airworthiness certification.
Standard

Regional Aircraft Towbarless Tow Vehicle - Test Requirements
2002-12-13
HISTORICAL
ARP5911
The present Aerospace Recommended Practice specifies for airplane operator and tow vehicle manufacturers the basic testing requirements for towbarless tow vehicles to be used on the nose gear of conventional tricycle type landing gears of commercial civil transport aircraft with maximum ramp weight between 8,600 kg (19,000 lb) and 50,000 kg (110,000 lb), commonly designated as “regional aircraft”. Its purpose is to achieve testing results, or equivalent computer modeling, demonstrating that the loads induced by the tow vehicle will not exceed the design loads of the airplane's nose landing gear and associated structure, reduce the certified safe life limit of the nose landing gear, or otherwise compromise the airplane's structural integrity and airworthiness certification.
12Next >Last >>
X