Refine Your Search

Date

Date

Test procedures Hydraulic Brake Components Standards Committee

Search Results

Viewing 1 to 16 of 16
1
Sort by relevance
Standard

Materials for Plastic Check Valves for Vacuum Booster Systems
2001-05-14
CURRENT
J1875_200105
The materials defined by this SAE Standard are unreinforced thermoplastic acetal and thermoplastic 6/6 heat stabilized nylon, as both materials will function in this application. The specific material chosen will depend on the final application's surroundings and heat requirements. They are for use in vacuum booster check valves for hydraulic brake systems.
Standard

Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes - Performance Requirements
2012-04-30
CURRENT
J1694_201204
This SAE Recommended Practice defines minimum requirements for general characteristics, performance, and durability. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves, or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The general characteristics and test procedure are specified in SAE J1693.
Standard

Materials for Plastic Pistons for Hydraulic Disc Brake Cylinders
2001-05-14
HISTORICAL
J1568_200105
The materials defined by this SAE Standard are glass-fiber-reinforced, mineral-filled phenolic molding compounds suitable for compression molding. Preforms may be radio frequency preheated or screw preheated slugs. Compound for use in hydraulic disc brake caliper pistons.
Standard

Materials for Plastic Pistons for Hydraulic Disc Brake Cylinders
2012-04-30
CURRENT
J1568_201204
The materials defined by this SAE Standard are glass-fiber-reinforced, mineral-filled phenolic molding compounds suitable for compression molding. Preforms may be radio frequency preheated or screw preheated slugs. Compound for use in hydraulic disc brake caliper pistons.
Standard

Brake Master Cylinder Reservoir Diaphragm Gasket
2014-11-26
CURRENT
J1605_201411
This SAE Standard covers performance requirements and methods of test for master cylinder reservoir diaphragm gaskets that will provide a functional seal and protection from outside dirt and water.
Standard

BRAKE MASTER CYLINDER RESERVOIR DIAPHRAGM GASKET
1992-03-20
HISTORICAL
J1605_199203
This SAE Standard covers performance requirements and methods of test for master cylinder reservoir diaphragm gaskets that will provide a functional seal and protection from outside dirt and water.
Standard

Plastic Dust Shield for Hydraulic Disc Brakes
2012-03-20
CURRENT
J1876_201203
The material defined by this SAE document is an impact modified, heat stabilized, 66 nylon reinforced with glass fibers. This material is for use in dust shields for hydraulic disc brakes. NOTE—The applicability of a plastic dust shield must be evaluated for each individual brake system. Its use with solid rotors and/or high performance brake systems is not recommended.
Standard

Plastic Dust Shield for Hydraulic Disc Brakes
2001-05-14
HISTORICAL
J1876_200105
The material defined by this SAE document is an impact modified, heat stabilized, 66 nylon reinforced with glass fibers. This material is for use in dust shields for hydraulic disc brakes.
Standard

RUBBER BOOTS FOR DRUM-TYPE HYDRAULIC BRAKE WHEEL CYLINDERS
1989-10-01
HISTORICAL
J1604_198910
This document covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of -40 to + 120 ± 2°C (-40 to +248 ± 3.6°F).
Standard

RUBBER BOOTS FOR DRUM-TYPE HYDRAULIC BRAKE WHEEL CYLINDERS
1995-01-01
HISTORICAL
J1604_199501
This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of -40 to +120 °C ± 2 °C (-40 to + 248 °F ± 3.6 °F).
Standard

Rubber Boots for Drum-Type Hydraulic Brake Wheel Cylinders
2015-12-17
CURRENT
J1604_201512
This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of −40 to +120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F).
Standard

Hydraulic Valves for Motor Vehicle Brake Systems—Performance Requirements
2002-08-07
HISTORICAL
J1137_200208
This SAE Recommended Practice applies to valve assemblies that are used on passenger car and light truck braking systems utilizing motor vehicle hydraulic brake fluids. The procedure (SAE J1118) and these requirements (SAE J1137) were developed for brake fluids conforming to SAE J1703 and FMVSS 116 (DOT 3) requirements; however, it may be utilized for valves which use DOT 4 or DOT 5 brake fluid. These requirements are applicable to differential warning, metering hold off, bypass function, or proportioning type valves or any combination thereof.
Standard

HYDRAULIC VALVES FOR MOTOR VEHICLE BRAKE SYSTEMS—PERFORMANCE REQUIREMENTS
1995-06-01
HISTORICAL
J1137_199506
This SAE Recommended Practice applies to valve assemblies that are used on passenger car and light truck braking systems utilizing motor vehicle hydraulic brake fluids. The procedure (SAE J1118) and these requirements (SAE J1137) were developed for brake fluids conforming to SAE J1703 and FMVSS 116 (DOT 3) requirements; however, it may be utilized for valves which use DOT 4 or DOT 5 brake fluid. These requirements are applicable to differential warning, metering hold off, bypass function, or proportioning type valves or any combination thereof.
Standard

Rubber Dust Boots for the Hydraulic Disk Brake Piston
2012-04-30
CURRENT
J1570_201204
This SAE Standard covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation. The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operating in a temperature range of -40 to + 120 °C ± 2 °C (-40 to + 248 °F ± 3.6 °F).
Standard

Rubber Dust Boots for the Hydraulic Disk Brake Piston
2008-05-13
HISTORICAL
J1570_200805
This SAE Standard covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation. The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operating in a temperature range of −40 to + 120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F).
1
X