Search Results

Standard

SEAT BELT HARDWARE WEBBING ABRASION TEST PROCEDURE

1994-06-01

J339_199406

This SAE Recommended Practice describes a test procedure for evaluating the abrasion resistance characteristics of webbing when used in adjustment hardware of seat belt assemblies such as those described in SAE J140.

Standard

SEAT BELT ASSEMBLY WEBBING ABRASION TEST PROCEDURE

1986-03-01

J339_198603

This SAE Recommended Practice describes a test procedure for evaluating the abrasion resistance characteristics of webbing when used in buckles of seat belt assemblies such as those described in SAE J140a.

Standard

SEAT BELT ASSEMBLY WEBBING ABRASION TEST PROCEDURE

1968-05-01

J339_196805

This SAE Recommended Practice describes a test procedure for evaluating the abrasion resistance characteristics of webbing when used in buckles of seat belt assemblies such as those described in SAE J4.

Standard

SEAT BELT ASSEMBLY WEBBING ABRASION TEST PROCEDURE

1969-08-01

J339A_196908

This SAE Recommended Practice describes a test procedure for evaluating the abrasion resistance characteristics of webbing when used in buckles of seat belt assemblies such as those described in SAE J4.

Standard

SEAT BELT HARDWARE WEBBING ABRASION PERFORMANCE REQUIREMENTS

1994-06-01

J114_199406

This SAE Recommended Practice describes the performance requirements for abrasion resistance of webbing when used in adjustment hardware normally used to adjust the length of seat belt assemblies such as those described in SAE J140. These requirements are applicable to tests conducted according to the procedure described in SAE J339. Although adjustment hardware is normally the primary source of webbing abrasion in a seat belt assembly, consideration should be given to other areas of normal webbing contact in the restraint system that may provide a more severe condition of webbing abrasion.

Standard

SEAT BELT ASSEMBLY WEBBING ABRASION TEST REQUIREMENTS

1969-08-01

J114_196908

This SAE Recommended Practice describes the test requirements for abrasion resistance of webbing when used in buckles or other manual adjusting devices normally used to adjust the length of seat belt assemblies such as those described in SAE J4. These requirements are applicable to tests conducted according to the procedure described in SAE J339.

Standard

SEAT BELT ASSEMBLY WEBBING ABRASION PERFORMANCE REQUIREMENTS

1986-03-01

J114_198603

This SAE Recommended Practice describes the performance requirements for abrasion resistance of webbing when used in buckles or other manual adjusting devices normally used to adjust the length of seat belt assemblies such as those described in SAE J140a. These requirements are applicable to tests conducted according to the procedure described in SAE J339a.

Standard

MOTOR VEHICLE SEAT BELT INSTALLATIONS

1962-08-01

J800A_196208

Standard

MOTOR VEHICLE SEAT BELT ASSEMBLY INSTALLATIONS

1986-04-01

J800_198604

It is the purpose of this SAE Recommended Practice to provide general installation instructions for universal type seat belt assemblies for installation in either a commercial or passenger car vehicle. Its primary intent is to provide guidance in the installation of seat belt assemblies meeting the requirements of Section 571.209 in the code of Federal Regulations of the National Highway Traffic Safety Administration. These minimum instruction requirements may be supplemented by more specific manufacturer's instructions, if they are necessary to provide proper installation in a particular vehicle.

Standard

MOTOR VEHICLE SEAT BELT ASSEMBLY INSTALLATION

1994-06-01

J800_199406

This SAE Recommended Practice provides general installation instructions for aftermarket, universal type seat belt assemblies for installation in passenger cars, trucks, buses, and multipurpose passenger vehicles. It applies only to seat belt assemblies which are not identified by a vehicle manufacturer part number or which are not designed for a specific vehicle application.

Standard

MOTOR VEHICLE SEAT BELT ASSEMBLY INSTALLATIONS

1965-09-01

J800B_196509

It is the purpose of this SAE Recommended Practice to define minimum requirements for content of the installation instruction sheet intended to accompany a seat belt assembly offered for installation in a motor vehicle at other than the vehicle manufacturer’s plant. Its primary intent is to provide guidance in the installation of seat belt assemblies meeting the requirements of SAE J4. These minimum instruction requirements may be supplemented by more specific manufacturer’s instructions, if they are necessary to provide proper installation in a particular vehicle.

Standard

MOTOR VEHICLE SEAT BELT ASSEMBLY INSTALLATIONS

1973-11-01

J800C_197311

It is the purpose of this SAE Recommended Practice to provide general installation instructions for universal type seat belt assemblies for installation in either a commercial or passenger car vehicle. Its primary intent is to provide guidance in the installation of seat belt assemblies meeting the requirements of the SAE J4 and Section 571.209 in the code of Federal Regulations of the National Highway Traffic Safety Administration. These minimum instruction requirements may be supplemented by more specific manufacturer’s instructions, if they are necessary to provide proper installation in a particular vehicle.

Standard

MOTOR VEHICLE SEAT BELT ANCHORAGES—PERFORMANCE REQUIREMENTS

1976-05-01

J385_197605

This SAE Recommended Practice specifies performance requirements for either static or dynamic testing of seat belt anchorages attached to vehicle structure or to the seat assemblies as installed in the motor vehicle (This SAE Recommended Practice supersedes the Performance Requirements Section of SAE J787bl. Design Requirements and Test Procedures are specified in Recommended Practice SAE J383, Motor Vehicle Seat Belt Anchorages—Design Recommendations and Recommended Practice SAE J384, Motor Vehicle Seat Belt Anchorages—Test Procedure.

Standard

MOTOR VEHICLE SEAT BELT ANCHORAGES--PERFORMANCE REQUIREMENTS

1986-04-01

J385_198604

This SAE Recommended Practice specifies performance requirements for either static or dynamic testing of seat belt anchorages attached to vehicle structure or to the seat assemblies as installed in the motor vehicle. (This SAE Recommended Practice supersedes the Performance Requirements Section of SAE J787b.) Design Requirements and Test Procedures are specified in Recommended Practice SAE J383, Motor Vehicle Seat Belt Anchorages--Design Recommendations and Recommended Practice SAE J384, Motor Vehicle Seat Belt Anchorages--Test Procedure.

Standard

Motor Vehicle Seat Belt Anchorages - Performance Requirements

2013-03-28

J385_201303

This SAE Recommended Practice specifies performance requirements for the strength of seat belt anchorages attached to vehicle structure or to the seat assemblies as installed in the motor vehicle. (This document supersedes the Performance Requirements Section of SAE J787b.) Design recommendations and test procedures are specified in SAE J383 and SAE J384, respectively.

Standard

MOTOR VEHICLE SEAT BELT ANCHORAGES—PERFORMANCE REQUIREMENTS

1995-03-01

J385_199503

This SAE Recommended Practice specifies performance requirements for the strength of seat belt anchorages attached to vehicle structure or to the seat assemblies as installed in the motor vehicle. (This document supersedes the Performance Requirements Section of SAE J787b.) Design recommendations and test procedures are specified in SAE J383 and SAE J384, respectively.

Standard

SEAT BELT RESTRAINT SYSTEM HARDWARE—GLOSSARY OF TERMS

1997-04-01

J1803_199704

This SAE Recommended Practice provides a Glossary of Terms commonly used to describe Seat Belt Restraint Systems Hardware and their function. These terms are currently defined in various SAE Recommended Practices but are sometimes inconsistent. It is intended for this document to supersede the definitions found in separate SAE Recommended Practices.

Standard

Seat Belt Restraint System Hardware—Glossary of Terms

2011-04-06

J1803_201104

This SAE Recommended Practice provides a Glossary of Terms commonly used to describe Seat Belt Restraint Systems Hardware and their function. These terms are currently defined in various SAE Recommended Practices but are sometimes inconsistent. It is intended for this document to supersede the definitions found in separate SAE Recommended Practices.

Standard

MOTOR VEHICLE SEAT BELT ANCHORAGES--TEST PROCEDURE

1986-04-01

J384_198604

This SAE Recommended Practice outlines both dynamic and static test procedures of seat belt anchorages attached to vehicle structure or seat assemblies installed in the vehicle. (This SAE Recommended Practice supersedes the Test Procedure Section of SAE J787b.) Design Recommendations and Performance Requirements are specified in the Recommended Practices SAE J383, Motor Vehicle Seat Belt Anchorages--Design Recommendations and SAE J385, Motor Vehicle Seat Belt Anchorages--Performance Requirements, respectively.

Standard

MOTOR VEHICLE SEAT BELT ANCHORAGES TEST PROCEDURE

1976-05-01

J384_197605

This SAE Recommended Practice outlines both dynamic and static test procedures of seat belt anchorages attached to vehicle structure or seat assemblies installed in the vehicle (This SAE Recommended Practice supersedes the Test Procedure Section of SAE J787b). Design Recommendations and Performance Requirements are specified in the Recommended Practices SAE J383. Motor Vehicle Seat Belt Anchorages—Design Recommendations and SAE J385. Motor Vehicle Seat Belt Anchorages—Performance Requirements, respectively.