Search Results

EGR coolers are effective to reduce NOx emissions from diesel engines due to lower intake charge temperature. EGR cooler fouling reduces heat transfer capacity of the cooler significantly and increases pressure drop across the cooler. Engine coolant provided at 40–90 C is used to cool EGR coolers. The presence of a cold surface in the cooler causes particulate soot deposition and hydrocarbon condensation. The experimental data also indicates that the fouling is mainly caused by soot and hydrocarbons. In this study, a 1-D model is extended to simulate particulate soot and hydrocarbon deposition on a concentric tube EGR cooler with a constant wall temperature. The soot deposition caused by thermophoresis phenomena is taken into account the model. Condensation of a wide range of hydrocarbon molecules are also modeled but the results show condensation of only heavy molecules at coolant temperature.

The use of hydrogen as a possible fuel for internal combustion (IC) engines can help build a society with a clean transportation framework. Diluting the in-cylinder mixture can improve the efficiency of the engines. To prove the validity of lean burn in hydrogen IC engines, three different combustion modes are investigated in this study. The engine experiments are conducted in a spray-guided direct-injection (DI) spark-ignition engine with 10 MPa of hydrogen DI. When lean burn is applied to a hydrogen IC engine, the characteristics of pumping and heat transfer loss improve. The improvement in heat transfer loss is more significant than the reduction in negative pumping work for the indicated thermal efficiency. Among the three combustion modes, stratified charge combustion (SCC) develops the maximum indicated mean effective pressure. However, this mode deteriorates the combustion stability slightly. The nitrogen oxide emission is reduced when the excess air ratio is increased.

The effects of combining premixed, low temperature combustion (LTC) with biodiesel are relatively unknown to this point. This mode allows simultaneously low soot and NOx emissions by using high rates of EGR and increasing ignition delay. This paper compares engine performance and emissions of neat, soy-based methyl ester biodiesel (B100), B20, B50, pure ultra low sulfur diesel (ULSD) and a Swedish, low aromatic diesel in a multi-cylinder diesel engine operating in a late-injection premixed LTC mode. Using heat release analysis, the progression of LTC combustion was explored by comparing fuel mass fraction burned. B100 had a comparatively long ignition delay compared with Swedish diesel when measured by start of ignition (SOI) to 10% fuel mass fraction burned (CA10). Differences were not as apparent when measured by SOI to start of combustion (SOC) even though their cetane numbers are comparable.

The combustion and exhaust emission characteristics of a DME fueled HCCI engine were investigated. Different fuel injection strategies were tested under various injection quantities and timings with exhaust gas recirculation (EGR). The combustion phase in HCCI was changed by an in-cylinder direct injection and EGR, due to changes in the in-cylinder temperature and mixture homogeneity. The gross indicated mean effective pressure (IMEPgross) increased and the hydrocarbon (HC) and carbon monoxide (CO) emissions decreased as the equivalence ratio was augmented. The IMEPgross with direct injection was greater than with the port injection due to retarded ignition timing resulting from latent heat of direct injected DME fuel. It was because that most of burn duration was completed before top dead center owing to higher ignitability for DME with high cetane number. However, HC and CO emissions were similar for both injection locations.

A quasi-dimensional computer simulation of the turbocharged spark-ignition engine has been developed in order to study system performance as various design parameters and operating conditions are varied. The simulation is of the “filling and emptying” type. Quasi-steady flow models of the compressor, intercooler, manifolds, turbine, wastegate, and ducting are coupled with a multi-cylinder engine model where each cylinder undergoes the same thermodynamic cycle. A turbulent entrainment model of the combustion process is used, thus allowing for studies of the effects of various combustion chamber shapes and turbulence parameters on cylinder pressure, temperature, NOx emissions and overall engine performance. Valve open areas are determined either based on user supplied valve lift data or using polydyne-generated cam profiles which allow for variable valve timing studies.

Dimethyl-ether combustion with pilot injection was investigated in a single cylinder direct injection diesel engine equipped with a common-rail injection system. Combustion characteristics and emissions were tested with dimethyl-ether and compared with diesel fuel. The main injection timing was fixed to have the best timings for maximum power output. The total injected fuel mass corresponded to a low heating value of 405 joules per cycle at 800 rpm. The fuel quantity and the injection timing of the pilot injection were varied from 8 to 20% of the total injected mass and from 50 to 10 crank angle degrees before the main injection timing, respectively. Ignition delay decreased with pilot injection. The effects of pilot injection were less significant with DME combustion than with diesel. Pilot injection caused the main combustion to increase in intensity resulting in decreased emissions of hydrocarbons, carbon monoxide and particulate matter.

Low temperature diesel combustion with a large amount of exhaust gas recirculation in a direct injection diesel engine was investigated. Tests were carried out under various engine speeds, injection pressures, injection timings, and injection quantities. Exhaust emissions and brake specific fuel consumption were measured at different torque and engine speed conditions. High rates of exhaust gas recirculation led to the simultaneous reduction of nitrogen oxide and soot emissions due to a lower combustion temperature than conventional diesel combustion. However, hydrocarbon and carbon monoxide emissions increased as the combustion temperature decreased because of incomplete combustion and the lack of an oxidation reaction. To overcome the operating range limits of low temperature diesel combustion, increased intake pressure with a modified turbocharger was employed.

The effect of the composition of propane (C₃H₈) and butane (C₄H₁₀) in liquefied petroleum gas (LPG) was investigated in a dual-fuel HCCI engine fueled with di-methyl ether (DME) and LPG. The composition of LPG affects DME-LPG dual fuel HCCI combustion due to the difference in the physical properties of propane that and butane such as octane number, auto-ignition temperature and heat of vaporization. DME was injected directly into the cylinder at various injection timing from 160 to 350 crank angle degrees (CAD). LPG was injected at the intake port with a fixed injection timing at 20 CAD. It was found that power output was increased with propane ratio. This gain in power output resulted from increased expansion work due to the better anti-knock properties of propane. However, higher propane ratio made combustion efficiency decrease because of the suppression in low temperature reaction of DME which determines heat release amount of high temperature reaction.

This paper reports the development of a model of diesel combustion and NO emissions, based on a modified eddy dissipation concept (EDC), and its implementation into the KIVA-3V multidimensional simulation. The EDC model allows for more realistic representation of the thin sub-grid scale reaction zone as well as the small-scale molecular mixing processes. Realistic chemical kinetic mechanisms for n-heptane combustion and NOx formation processes are fully incorporated. A model based on the normalized fuel mass fraction is implemented to transition between ignition and combustion. The modeling approach has been validated by comparison with experimental data for a range of operating conditions. Predicted cylinder pressure and heat release rates agree well with measurements. The predictions for NO concentration show a consistent trend with experiments. Overall, the results demonstrate the improved capability of the model for predictions of the combustion process.

A diesel-fueled premixed charged compression ignition (PCCI) combustion technique using a two-stage injection strategy has been investigated in a single cylinder optical engine equipped with a common-rail fuel system. Although PCCI combustion has the advantages of reducing NOx and PM emissions, difficulties in vaporization of a diesel fuel and control of the combustion phase hinder the development of the PCCI engine. A two-stage injection strategy was applied to relieve these problems. The first injection, named as main injection, was an early direct injection of diesel fuel into the cylinder to achieve premixing with air. The second injection was a diesel injection of a small quantity (1.5 mm3) as an ignition promoter and combustion phase controller near TDC. Effects of injection pressure, injected fuel quantity and compression ratio were studied with variation of an intake air temperature.

Exhaust gas recirculation (EGR) and lean burn utilize the diluents into the engine cylinder to control combustion leading to enhanced fuel economy and reduced emissions. However, the occurrence of excessive cyclic variation with high diluent rates, brings about an undesirable combustion instability within the engine cylinder resulting in the deterioration of both engine performance and emissions. Proper stratification of mixture and diluents could improve the combustion stability under high diluent environment. EGR stratification within the cylinder was made by adopting a fast-response solenoid valve in the midst of EGR line and controlling its timing and duty. With EGR in both homogeneous mode and stratified mode, in-cylinder pressure and emissions were measured. The thermodynamic heat release analysis showed that the burning duration was decreased in case of stratified EGR. It was found that the stratification of EGR hardly affected the emissions.

Conventional spark plugs ignite a fuel-air mixture via an electric-to-plasma energy transfer; the effectiveness of which can be described by an electric-to-plasma energy efficiency. Although conventional spark plug electric-to-plasma efficiencies have historically been viewed as adequate, it might be wondered how an increase in such an efficiency might translate (if at all) to improvements in the flame initiation period and eventual engine performance of a spark-ignition engine. A modification can be made to the spark plug that places a peaking capacitor in the path of the electrical current; upon coil energizing, the stored energy in the peaking capacitor substantially increases the energy delivered by the spark. A previous study has observed an improvement in the electric-to-plasma energy efficiency to around 50%, whereas the same study observed conventional spark plug electric-to-plasma energy efficiency to remain around 1%.

In the wake of global focus shifting towards the health and conservation of the planet, greater importance is placed upon the hazardous emissions of our fossil fuels, as well as their finite supply. These two areas remain intense topics of research in order to reduce greenhouse gas emissions and increase the fuel efficiency of vehicles, a sector which is a major contributor to society's global CO₂ emissions and consumer of fossil-fuel resources. A particular solution to this problem is the diesel engine, with its inherently fuel-lean combustion, which gives rise to low CO₂ production and higher efficiencies than other potential powertrain solutions. Diesel engines, however, typically exhibit higher nitrogen oxides (NOx) and soot engine-out emissions than their gasoline counterparts. NOx is an ingredient to ground-level ozone production and smoke is a possible carcinogen, both of which are facing stricter emissions regulations.

Internal combustion engines have dealt with increasingly restricted emissions requirements. After-treatment devices are successful bringing emissions into compliance, but in-cylinder combustion control can reduce their burden by reducing engine-out emissions. For example, oxides of nitrogen (NOx) are diesel combustion exhaust species of notoriety for their difficulty in after-treatment removal. In-cylinder conditions can be controlled for low levels of NOx, but this produces high levels of soot particulate matter (PM). The simultaneous reduction of NOx and PM can be realized through a combustion process known as low temperature combustion (LTC). This paper presents an investigation into the manifestation of LTC in the calculated heat release profile. Such a study could be important since some extreme LTC conditions may exhibit a return to the soot-NOx tradeoff, rendering an emissions-based definition of LTC unhelpful.

The compression ignition combustion fuelled with hydrogen and dimethyl-ether was investigated. Exhaust gas recirculation was applied to reduce noise and nitrogen oxide (NOx) emission. When dimethyl-ether was injected earlier, combustion showed two-stage ignitions known as low temperature reaction and high temperature reaction. With advanced dimethyl-ether injection, combustion temperature and in-cylinder pressure rise were lowered which resulted in high carbon monoxide and hydrocarbon emissions. However, NOx emission was decreased due to relatively low combustion temperature. The engine combustion showed only high temperature reaction when dimethyl-ether was injected near top dead center. When exhaust gas recirculation gas was added, the in-cylinder pressure and heat release rate were decreased. However, it retarded combustion phase resulting in higher indicated mean effective pressure.

The effect of pilot injection and exhaust gas recirculation (EGR) on premixed charge compression ignition (PCCI) combustion was investigated in a single-cylinder direct-injection diesel engine with low engine speed and low load. The injection timing of PCCI combustion was fixed at 25 ~ 30 crank angle degree before top dead center (°CA BTDC) based on the ignition delay and power output. The level of oxides of nitrogen (NOx) emissions of PCCI combustion was 68% lower than that of conventional diesel combustion owing to the reduction of near-stoichiometric region which is well known as the main source of NOx formation. However, the indicated mean effective pressure (IMEP), hydrocarbon (HC), particulate matter (PM) and carbon monoxide (CO) emissions deteriorated compared with conventional diesel combustion because of early injection, advanced combustion phase and lowered combustion temperature. EGR has been applied to PCCI combustion.

Exhaust gas recirculation (EGR) coolers are commonly used in diesel engines to reduce the temperature of recirculated exhaust gases in order to reduce NOx emissions. The presence of a cool surface in the hot exhaust causes particulate soot deposition as well as hydrocarbon and water condensation. Fouling experienced through deposition of particulate matter and hydrocarbons results in degraded cooler effectiveness and increased pressure drop. In this study, a visualization test setup is designed and constructed so that the effect of water condensation on the deposit formation and growth at various coolant temperatures can be studied. A water-cooled surrogate rectangular channel is employed to represent the EGR cooler. One side of the channel is made of glass for visualization purposes. A medium duty diesel engine is used to generate the exhaust stream.

Finding a replacement for fossil fuels is critical for the future of automotive transportation. The compression ignition (CI) engine is an important aspect of everyday life by means of transportation and shipping of materials. Biodiesel is a viable augmentation for conventional diesel fuel in compression ignition engines. Biodiesel-fuelled diesel engines produce less particulate matter (PM) relative to conventional diesel and biodiesel has the ability to be a carbon dioxide (CO₂) neutral fuel, which may come under government regulation as a greenhouse gas. Although biodiesel is a viable diesel replacement and has certain emissions benefits, it typically also has a known characteristic of higher oxides of nitrogen (NOx) emissions relative to petroleum diesel. Advanced modes of combustion such as low temperature combustion (LTC) have attained much attention due to ever-increasing emission standards, and could also help reduce NOx in biodiesel.

Premixed compression ignition low-temperature diesel combustion (PCI) can simultaneously reduce particulate matter (PM) and oxides of nitrogen (NOx). Carbon monoxide (CO) and total hydrocarbon (THC) emissions increase relative to conventional diesel combustion, however, which may necessitate the use of a diesel oxidation catalyst (DOC). For a better understanding of conventional and PCI combustion, and the operation of a platinum-based production DOC, engine-out and DOC-out exhaust hydrocarbons are speciated using gas chromatography. As combustion mode is changed from lean conventional to lean PCI to rich PCI, engine-out CO and THC emissions increase significantly. The relative contributions of individual species also change; increasing methane/THC, acetylene/THC and CO/THC ratios indicate a richer combustion zone and a reduction in engine-out hydrocarbon incremental reactivity.

The More precise control of the multiple-injection is required in common-rail injection system of direct injection diesel engine to meet the low NOx emission and optimal PM filter system. The main parameter for obtaining the multiple-injections is the mechanism controlling the injector needle energizing and movement. In this study, a piezo-driven diesel injector, as a new method driven by piezoelectric energy, has been applied with a purpose to develop the analysis model of the piezo actuator to predict the dynamics characteristics of the hydraulic component (injector) by using the AMESim code and to evaluate the effect of this control capability on spray formation processes. Aimed at simulating the hydraulic behavior of the piezo-driven injector, the circuit model has been developed and verified by comparison with the experimental results.