Refine Your Search

Date

Date

Topic

Topic

Vehicle E E System Diagnostic Standards Committee High voltage systems Diesel particulate filters Chassis

Search Results

Viewing 1 to 20 of 25
12Next >Last >>
Sort by relevance
Standard

E/E DIAGNOSTIC DATA COMMUNICATIONS
1990-11-01
HISTORICAL
J2054_199011
This SAE Information Report describes the diagnostic data communications required for implementation of a set of diagnostic test modes for all electronic systems on the vehicle's serial data link. These test modes can be used by off-board test equipment for both service and assembly plant testing. The goal of this document is to provide standard methods to perform common functions for all electronic systems. This standard set of procedures will aid development, production, and field service of those systems. Use of the standard data communications in this specification will potentially result in the following benefits: This specification includes:
Standard

General Motors UART Serial Data Communications
2005-12-19
HISTORICAL
J2740_200512
This Technical Information Report defines the General Motors UART Serial Data Communications Bus, commonly referred to as GM UART. This document should be used in conjunction with SAE J2534-2 in order to enhance an SAE J2534 interface to also provide the capability to program ECUs with GM UART. SAE J2534-1 includes requirements for an interface that can be used to program certain emission-related Electronic Control Units (ECUs) as required by U.S. regulations, and SAE J2534-2 defines enhanced functionality required to program additional ECUs not mandated by current U.S. regulations. The purpose of this document is to specify the requirements necessary to implement GM UART in an enhanced SAE J2534 interface intended for use by independent automotive service facilities to program GM UART ECUs in General Motors vehicles.
Standard

General Motors UART Serial Data Communications
2019-05-20
CURRENT
J2740_201905
This Technical Information Report defines the General Motors UART Serial Data Communications Bus, commonly referred to as GM UART. This document should be used in conjunction with SAE J2534-2 in order to enhance an SAE J2534 interface to also provide the capability to program ECUs with GM UART. SAE J2534-1 includes requirements for an interface that can be used to program certain emission-related Electronic Control Units (ECUs) as required by U.S. regulations, and SAE J2534-2 defines enhanced functionality required to program additional ECUs not mandated by current U.S. regulations. The purpose of this document is to specify the requirements necessary to implement GM UART in an enhanced SAE J2534 interface intended for use by independent automotive service facilities to program GM UART ECUs in General Motors vehicles.
Standard

NOx Tracking Parameter Accuracy
2022-08-05
CURRENT
J3349_202208
This SAE Information Report provides SAE’s recommendations for meeting the requirements for REAL NOx accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in OBD regulations 13 CCR 1971.1 and 13 CCR 1968.2.
Standard

NOx Tracking Parameter Accuracy
2021-10-19
HISTORICAL
J3349_202110
This SAE Information Report provides SAE’s recommendations for meeting the requirements for REAL NOx accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in OBD regulations 13 CCR 1971.1 and 13 CCR 1968.2.
Standard

E/E Diagnostic Test Modes: Zero Emission Vehicle Propulsion Systems on UDS (ZEVonUDS)
2022-12-16
CURRENT
J1953_202306
SAE J1979-3 describes the communication between the zero emissions propulsion systems and test equipment required by government regulations. Standardization regulations require passenger cars and light-, medium-, and heavy-duty trucks to support a minimum set of diagnostic information to external (off-board) “generic” test equipment. To achieve this, SAE J1979-3 is based on the Open Systems Interconnection (OSI) Basic Refer to Model in accordance with ISO/IEC 7498-1 and ISO/IEC 10731, which structures communication systems into seven layers.
Standard

Optional Pass-Thru Features
2020-12-14
CURRENT
J2534-2_202012
SAE J2534-1 defines a standard vehicle network interface that can be used to reprogram emission-related control modules. However, there is a need to support vehicles prior to the 2004 model year, as well as non-emission related control modules. The SAE J2534-2 document meets these needs by detailing extensions to API version 04.04 of the SAE J2534-1 specification. It is not required for an interface to be fully compliant with API version 04.04 of the SAE J2534-1 specification to implement some of the features specified in this document. Together, these extensions provide the framework for a common interface to protect the software investment of the vehicle OEMs and scan tool manufacturers. Only the optional features will be described by this document and are based on the December 2004 publication of SAE J2534-1.
Standard

Optional Pass-Thru Features
2019-01-16
HISTORICAL
J2534/2_201901
SAE J2534-1 defines a standard vehicle network interface that can be used to reprogram emission-related control modules. However, there is a need to support vehicles prior to the 2004 model year, as well as non-emission related control modules. The SAE J2534-2 document meets these needs by detailing extensions to an SAE J2534-1 specification. It is not required for an interface to be fully compliant with SAE J2534-1 specification to implement some of the features specified in this document. Together, these extensions provide the framework for a common interface to protect the software investment of the Vehicle OEMs and Scan Tool manufacturers. Only the optional features will be described by this document and are based on the December 2004 publication of SAE J2534-1.
Standard

Optional Pass-Thru Features
2010-10-26
HISTORICAL
J2534/2_201010
SAE J2534-1 defines a standard vehicle network interface that can be used to reprogram emission-related control modules. However, there is a need to support vehicles prior to the 2004 model year as well as non-emission related control modules. The SAE J2534-2 document meets these needs by detailing extensions to an SAE J2534-1 specification. It is not required for an interface to be fully compliant with SAE J2534-1 specification to implement some of the features specified in this document. Together, these extensions provide the framework for a common interface to protect the software investment of the Vehicle OEMs and Scan Tool manufacturers. Only the optional features will be described by this document and are based on the December 2004 publication of SAE J2534-1.
Standard

DIAGNOSTIC CONNECTOR
1992-06-01
HISTORICAL
J1962_199206
This SAE Recommended Practice: a Defines the functional requirements for a vehicle electrical/electronic diagnostic connector. These functional requirements are separated into two principal areas: connector location/access and connector design. b Establishes terminal assignments to conform to either of two categories: Standard or Manufacturer Discretionary. Rationale relative to intent is provided, where applicable, to minimize ambiguity.
Standard

Diagnostic Connector Equivalent to ISO/DIS 15031-3: December 14, 2001
2012-07-26
HISTORICAL
J1962_201207
This document supersedes SAE J1962 200204, and is technically equivalent to ISO/DIS 15031-3: December 14, 2001. This document is intended to satisfy the requirements of an OBD connector as required by U.S. On-Board Diagnostic (OBD) regulations. The diagnostic connection specified in this document consists of two mating connectors, the vehicle connector and the external test equipment connector. This document specifies: a The functional requirements for the vehicle connector. These functional requirements are separated into four principal areas: connector location/access, connector design, connector contact allocation, and electrical requirements for connector and related electrical circuits, b The functional requirements for the external test equipment connector. These functional requirements are separated into three principal areas: connector design, connector contact allocation, and electrical requirements for connector and related electrical circuits.
Standard

Diagnostic Connector
2015-09-11
HISTORICAL
J1962_201509
This document supersedes SAE J1962 200204, and is technically equivalent to ISO/DIS 15031-3: December 14, 2001. This document is intended to satisfy the requirements of an OBD connector as required by U.S. On-Board Diagnostic (OBD) regulations. The diagnostic connection specified in this document consists of two mating connectors, the vehicle connector and the external test equipment connector. This document specifies: a The functional requirements for the vehicle connector. These functional requirements are separated into four principal areas: connector location/access, connector design, connector contact allocation, and electrical requirements for connector and related electrical circuits, b The functional requirements for the external test equipment connector. These functional requirements are separated into three principal areas: connector design, connector contact allocation, and electrical requirements for connector and related electrical circuits.
Standard

Honda Diagnostic Serial Data Link Protocol - ABS/VSA System
2017-10-09
CURRENT
J2809_201710
This Technical Information Report defines the proprietary diagnostic communication protocol for ABS or VSA ECU (Electronic Control Unit) implemented on some Honda vehicles. This protocol does not apply to all Honda vehicles. This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an enhanced SAE J2534 interface. The purpose of this document is to specify the requirements necessary to implement the communication protocol in an enhanced SAE J2534 interface.
Standard

Honda Diagnostic Serial Data Link Protocol—ABS/VSA System
2007-10-11
HISTORICAL
J2809_200710
This Technical Information Report defines the proprietary diagnostic communication protocol for ABS or VSA ECU (Electronic Control Unit) implemented on some Honda vehicles. This protocol does not apply to all Honda vehicles. This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an enhanced SAE J2534 interface. The purpose of this document is to specify the requirements necessary to implement the communication protocol in an enhanced SAE J2534 interface.
Standard

Vehicle OBD II Compliance Test Cases
2015-07-28
HISTORICAL
J1699/3_201507
The main purpose of this Recommended Practice is to verify that vehicles are capable of communicating a minimum subset of information, in accordance with the diagnostic test services specified in SAE J1979: E/EDiagnostic Test Modes, or the equivalent document ISO 15031-5: Communication Between Vehicle and External Equipment for Emissions-Related Diagnostics - Part 5: Emissions-related diagnostic services. Any software meeting these specifications will utilize the vehicle interface that is defined in SAE J2534, Recommended Practice for Pass-Thru Vehicle Programming.
Standard

Vehicle OBD II Compliance Test Cases
2017-07-21
HISTORICAL
J1699/3_201707
The main purpose of this Recommended Practice is to verify that vehicles are capable of communicating a minimum subset of information, in accordance with the diagnostic test services specified in SAE J1979: E/E Diagnostic Test Modes, or the equivalent document ISO 15031-5: Communication Between Vehicle and External Equipment for Emissions-Related Diagnostics – Part 5: Emissions-related diagnostic services. Any software meeting these specifications will utilize the vehicle interface that is defined in SAE J2534, Recommended Practice for Pass-Thru Vehicle Programming.
Standard

Vehicle OBD II Compliance Test Cases
2021-04-28
CURRENT
J1699/3_202104
The main purpose of this SAE Recommended Practice is to verify that vehicles are capable of communicating a minimum subset of information in accordance with the diagnostic test services specified in SAE J1979, or the equivalent document ISO 15031-5. Any software meeting these specifications will utilize the vehicle interface that is defined in SAE J2534. SAE J1699-3 tests shall be run using an SAE J2534-1 (API Version 04.04) Interface. However, the use of an SAE J2534-2 (API Version 04.04) Interface shall be permitted if the following conditions are met: The number of 29-bit ISO 15765 OBD ECUs exceeds the capability of the SAE J2534-1 Interface. The SAE J2534-2 Interface meets or exceeds all of the SAE J2534-1 requirements and also supports the SAE J2534-2 feature “Mixed Format Frames on a CAN Network.”
Standard

Vehicle OBD II Compliance Test Cases
2012-05-11
HISTORICAL
J1699/3_201205
The main purpose of this Recommended Practice is to verify that vehicles are capable of communicating a minimum subset of information, in accordance with the diagnostic test services specified in SAE J1979: E/E Diagnostic Test Modes, or the equivalent document ISO 15031-5: Communication Between Vehicle and External Equipment for Emissions-Related Diagnostics – Part 5: Emissions-related diagnostic services. Any software meeting these specifications will utilize the vehicle interface that is defined in SAE J2534, Recommended Practice for Pass-Thru Vehicle Programming.
12Next >Last >>
X