Refine Your Search

Topic

Search Results

Journal Article

Investigations on Spark and Corona Ignition of Oxymethylene Ether-1 and Dimethyl Carbonate Blends with Gasoline by High-Speed Evaluation of OH* Chemiluminescence

2018-03-01
Abstract Bio-fuels of the 2nd generation constitute a key approach to tackle both Greenhouse Gas (GHG) and air quality challenges associated with combustion emissions of the transport sector. Since these fuels are obtained of residual materials of the agricultural industry, well-to-tank CO2 emissions can be significantly lowered by a closed-cycle of formation and absorption of CO2. Furthermore, studies of bio-fuels have shown reduced formation of particulate matter on account of the fuels’ high oxygen content therefore addressing air quality issues. However, due to the high oxygen content and other physical parameters these fuels are expected to exhibit different ignition behaviour. Moreover, the question is whether there is a positive superimposition of the fuels ignition behaviour with the benefits of an alternative ignition system, such as a corona ignition.
Journal Article

HMI for Left Turn Assist (LTA)

2018-03-01
Abstract Potential collisions with oncoming traffic while turning left belong to the most safety-critical situations accounting for ~25% of all intersection crossing path crashes. A Left Turn Assist (LTA) was developed to reduce the number of crashes. Crucial for the effectiveness of the system is the design of the human-machine interface (HMI), i.e. defining how the system uses the calculated crash probability in the communication with the driver. A driving simulator study was conducted evaluating a warning strategy for two use cases: firstly, the driver comes to a stop before turning (STOP), and secondly, the driver moves on without stopping (MOVE). Forty drivers drove through three STOP and two MOVE scenarios. For the STOP scenarios, the study compared the effectiveness of an audio-visual warning with an additional brake intervention and a baseline. For the MOVE scenarios, the study analyzed the effectiveness of the audio-visual warning against a baseline.
Journal Article

Integrated Positioning Method for Intelligent Vehicle Based on GPS and UWB

2017-09-23
Abstract Knowledge of intelligent vehicle absolute position is a vital premise for the implementation of decision programming, kinematic and dynamics control. In order to achieve high accuracy positioning and reduce running cost as much as possible under all operating conditions, this paper proposed an integrated positioning method based on GPS and Ultra Wide Band(UWB) for intelligent vehicle’s navigation and position system. In this method, GPS and UWB are alternately active according to the confidence level of GPS signal. When the vehicle is traveling in a wide-open area and GPS signal is well received, the positioning results of Dead Reckoning system are corrected by the low frequency positioning output from GPS. During the correcting process, in order to realize the better fusion of measurement data, a simplified federal Kalman filter was designed by using indirect method.
Journal Article

3D Scene Reconstruction with Sparse LiDAR Data and Monocular Image in Single Frame

2017-09-23
Abstract Real-time reconstruction of 3D environment attributed with semantic information is significant for a variety of applications, such as obstacle detection, traffic scene comprehension and autonomous navigation. The current approaches to achieve it are mainly using stereo vision, Structure from Motion (SfM) or mobile LiDAR sensors. Each of these approaches has its own limitation, stereo vision has high computational cost, SfM needs accurate calibration between a sequences of images, and the onboard LiDAR sensor can only provide sparse points without color information. This paper describes a novel method for traffic scene semantic segmentation by combining sparse LiDAR point cloud (e.g. from Velodyne scans), with monocular color image. The key novelty of the method is the semantic coupling of stereoscopic point cloud with color lattice from camera image labelled through a Convolutional Neural Network (CNN).
Journal Article

Efficient Lane Detection Using Deep Lane Feature Extraction Method

2017-09-23
Abstract In this paper, an efficient lane detection using deep feature extraction method is proposed to achieve real-time lane detection in diverse road environment. The method contains three main stages: 1) pre-processing, 2) deep lane feature extraction and 3) lane fitting. In pre-processing stage, the inverse perspective mapping (IPM) is used to obtain a bird's eye view of the road image, and then an edge image is generated using the canny operator. In deep lane feature extraction stage, an advanced lane extraction method is proposed. Firstly, line segment detector (LSD) is applied to achieve the fast line segment detection in the IPM image. After that, a proposed adaptive lane clustering algorithm is employed to gather the adjacent line segments generated by the LSD method. Finally, a proposed local gray value maximum cascaded spatial correlation filter (GMSF) algorithm is used to extract the target lane lines among the multiple lines.
Journal Article

Obstacle Avoidance for Self-Driving Vehicle with Reinforcement Learning

2017-09-23
Abstract Obstacle avoidance is an important function in self-driving vehicle control. When the vehicle move from any arbitrary start positions to any target positions in environment, a proper path must avoid both static obstacles and moving obstacles of arbitrary shape. There are many possible scenarios, manually tackling all possible cases will likely yield a too simplistic policy. In this paper reinforcement learning is applied to the problem to form effective strategies. There are two major challenges that make self-driving vehicle different from other robotic tasks. Firstly, in order to control the vehicle precisely, the action space must be continuous which can’t be dealt with by traditional Q-learning. Secondly, self-driving vehicle must satisfy various constraints including vehicle dynamics constraints and traffic rules constraints. Three contributions are made in this paper.
Journal Article

Personalized Controller Design for Electric Power Steering System Based on Driver Behavior

2017-09-23
Abstract Electric power steering (EPS) system is a kind of dynamic control system for vehicle steering, which can amplify the driver steering torque inputs to the vehicle to improve steering comfortable and performance, but the present EPS can’t cater to the driving habits of different people. In this paper, a personalized EPS controller is designed based on the driver behavior, which combines real-time driver behavior identification strategy with personalized assistance characteristic. Firstly, the driver behavior data acquisition system is designed and established, based on which, the input data of different kinds of drivers along with vehicle signals are collected under typical working conditions, then the identification of driver behavior online is realized using the BP neural network.
Journal Article

2-D CFAR Procedure of Multiple Target Detection for Automotive Radar

2017-09-23
Abstract In Advanced Driver Assistant System (ADAS), the automotive radar is used to detect targets or obstacles around the vehicle. The procedure of Constant False Alarm Rate (CFAR) plays an important role in adaptive targets detection in noise or clutter environment. But in practical applications, the noise or clutter power is absolutely unknown and varies over the change of range, time and angle. The well-known cell averaging (CA) CFAR detector has a good detection performance in homogeneous environment but suffers from masking effect in multi-target environment. The ordered statistic (OS) CFAR is more robust in multi-target environment but needs a high computation power. Therefore, in this paper, a new two-dimension CFAR procedure based on a combination of Generalized Order Statistic (GOS) and CA CFAR named GOS-CA CFAR is proposed. Besides, the Linear Frequency Modulation Continuous Wave (LFMCW) radar simulation system is built to produce a series of rapid chirp signals.
Journal Article

Discussion on Charging Control Strategy for Power Battery at Low Temperatures

2017-10-08
Abstract In the case of electric vehicles, due to the charging current limitation of lithium battery at low temperatures (below -20°C), it has been proposed to heat the battery pack up to a suitable temperature range before charging through a liquid-heating plate with PTC. However, at a low state of charge (SOC), there is a question which one could take the place of battery pack to supply power for PTC when heating. So that off-board charger (OFC) has been considered to supply power for PTC in this paper. In order to control the current charging into the battery pack as less as possible at low temperatures, three control schemes of battery management system (BMS) are proposed and compared. Scheme 1: BMS controls the value of charging current request close to the working current of PTC. Scheme 2: BMS controls the value of charging voltage request to reach a state of relative balance. Scheme 3: BMS disconnects the pack from the charger and keeps the connection between PTC and charger.
Journal Article

Bench Testing Validation of Wireless Power Transfer up to 7.7kW Based on SAE J2954

2017-10-08
Abstract Wireless Power Transfer (WPT) is presently being applied to consumer electronics in the low-power range and is planned to be commercialized in the high-power range for plug-in and electric vehicles in 2018. There are, however, many technology challenges remaining before widespread implementation of high-power WPT will occur. The SAE Vehicle Wireless Power and Alignment Taskforce published the Technical Information Report J2954 in 2016 to help harmonize the first phase of high-power WPT technology development. SAE J2954 adopts a performance-based approach to standardizing WPT by specifying ground and assembly coils to be used in a test stand (per Z-class) to validate performance, interoperability and safety. The main goal of this SAE J2954 bench testing campaign was to prove interoperability between WPT systems utilizing different coil magnetic topologies for SAE TIR J2954.
Journal Article

Power Analysis and Fault Attacks against Secure CAN: How Safe Are Your Keys?

2018-02-14
Abstract Designers of automotive systems find themselves pulled in an impossible number of directions. Systems must use the most advanced security features, but at the same time run on low-cost and resource-constrained hardware. Ultimately, an engineering trade-off will eventually be made regarding how encryption and key management is used on these systems, potentially leaving them vulnerable to attack. In this paper, we detail the applicability of side-channel power analysis and fault injection on automotive electronic systems, showing how these dangerous techniques can be used to break an otherwise secure system. We build a small example network using AES-CCM to implement an encrypted, authenticated CAN protocol. We demonstrate how open-source hardware and software can easily recover the encryption keys from some of these nodes with side-channel power analysis, and we recover a full firmware image from one device with a fault-injection attack using the same tools.
Journal Article

Automated ASIL Allocation and Decomposition according to ISO 26262, Using the Example of Vehicle Electrical Systems for Automated Driving

2018-04-18
Abstract ISO 26262 needs to be considered when developing safety-relevant E/E systems within the automotive industry. One part of the development process according to ISO 26262 is the derivation of the safety requirements for component functions. Here, one attribute of the safety requirements is the Automotive Safety Integrity Level (ASIL). The ASIL at a component level can be determined using ASIL allocation and decomposition. Considering complex systems such as vehicle electrical systems, countless possibilities can be identified for how the ASILs at a component level can be assigned in line with safety goals. In terms of efficiency, manual assignment is not expedient. Therefore, an algorithm for automated assignment of the ASILs will be introduced which considers constraints based on a fault tree analysis. The function of the approach will be demonstrated using the example of a vehicle electrical system from an automated vehicle.
Journal Article

Design, Analysis, and Optimization of a Multi-Speed Powertrain for Class-7 Electric Trucks

2018-04-17
Abstract The development, analysis, and optimization of battery electric class-7 heavy-duty trucks equipped with multi-speed transmissions are discussed in this paper. The designs of five new traction motors-fractional-slot, concentrated winding machines-are proposed for use in heavy-duty electric trucks. The procedure for gear-ratio range selection is outlined and ranges of gear ratios for three-to six-speed transmission powertrains are calculated for each of the proposed electric traction motors. The simulation and gear-ratio optimization tasks for class-7 battery electric trucks are formulated. The energy consumption of the e-truck with the twenty possible powertrain combinations is minimized over the four driving cycles and the most efficient powertrain layouts that meet the performance criteria are recommended.
Journal Article

A Bibliographical Review of Electrical Vehicles (xEVs) Standards

2018-04-18
Abstract This work puts presents an all-inclusive state of the art bibliographical review of all categories of electrified transportation (xEVs) standards, issued by the most important standardization organizations. Firstly, the current status for the standards by major organizations is presented followed by the graphical representation of the number of standards issued. The review then takes into consideration the interpretation of the xEVs standards developed by all the major standardization organizations across the globe. The standards are differentiated categorically to deliver a coherent view of the current status followed by the explanation of the core of these standards. The ISO, IEC, SAE, IEEE, UL, ESO, NTCAS, JARI, JIS and ARAI electrified transportation vehicles xEV Standards from USA, Europe, Japan, China and India were evaluated. A total approximated of 283 standards in the area have been issued.
Journal Article

Investigation of a Six-Phase Interior Permanent Magnet Synchronous Machine for Integrated Charging and Propulsion in EVs

2018-04-17
Abstract Merits such as reduced weight, overall and operational costs of the electric vehicle (EV) while providing level 3 charging capability, are propelling research on integrated charging (IC) technology for EVs. Since the same interior permanent magnet synchronous machine (IPMSM) is used during IC and traction conditions, it is important to understand the behavior of the machine during these conditions and optimally design the machine. Hence, firstly, this paper presents a case study on performance of a laboratory 3-phase IPMSM under IC and traction conditions. Thereafter, understanding the challenges such as low magnet operating point, losses and torque oscillation in 3-phase IPMSM during IC, a 6-phase IPMSM with an unconventional configuration is investigated to yield traction characteristics like that of the 3-phase IPMSM and mitigate challenges during IC. In the process, mathematical model of the 6-phase IPMSM is developed employing the dq-axis theory.
Journal Article

On WTW and TTW Specific Energy Consumption and CO2 Emissions of Conventional, Series Hybrid and Fully Electric Buses

2018-04-17
Abstract Making use of a specifically designed dynamical vehicle model, the authors here presented the results of an activity for the evaluation of energy consumption and CO2 emissions of buses for urban applications. Both conventional and innovative (series hybrid, and fully electric) vehicles were considered to obtain interesting comparative conclusions. The derived tool was used to simulate the dynamical behaviour of these vehicles on a number of kinematic profiles measured during real buses operation in different contexts, varying from really congested city centre routes to fast-lane operated services. It was so possible to evaluate the energetic performances of those buses on a Tank-to-Wheel (TTW) basis.
Journal Article

Parasitic Battery Drain Problems and AUTOSAR Acceptance Testing

2018-04-18
Abstract Battery Drain problems can occur in the vehicle due to improper network management between electronic control units (ECUs). Aim of this paper is to identify the factors that cause transmission and cease of transmission of a network management message of an ECU along with its application messages that controls the sleep/wake-up performance of other ECUs in the network. Strategy used here is, based on the root cause analysis of problems found in Display unit in vehicle environment, the functional CAN signals impacting sleep/wake-up behavior is re-mapped along with the state flow transition of AUTOSAR NM Algorithm. A re-defined test case design and simulation for vehicle model is created. Especially it focuses on validating the impact of functional CAN signals on DUT’s sleep/wake-up performance.
Journal Article

An Adaptive Neuro-Fuzzy Inference System (ANFIS) Based Model for the Temperature Prediction of Lithium-Ion Power Batteries

2018-08-14
Abstract Li-ion batteries have been widely applied in the areas of personal electronic devices, stationary energy storage system and electric vehicles due to their high energy/power density, low self-discharge rate and long cycle life etc. For the better designs of both the battery cells and their thermal management systems, various numerical approaches have been proposed to investigate the thermal performance of power batteries. Without the requirement of detailed physical and thermal parameters of batteries, this article proposed a data-driven model using the adaptive neuro-fuzzy inference system (ANFIS) to predict the battery temperature with the inputs of ambient temperature, current and state of charge. Thermal response of a Li-ion battery module was experimentally evaluated under various conditions (i.e. ambient temperature of 0, 5, 10, 15 and 20 °C, and current rate of C/2, 1C and 2C) to acquire the necessary data sets for model development and validation.
Journal Article

A Comprehensive Data Reduction Algorithm for Automotive Multiplexing

2019-04-08
Abstract Present-day vehicles come with a variety of new features like the pre-crash warning, the vehicle-to-vehicle communication, semi-autonomous driving systems, telematics, drive by wire. They demand very high bandwidth from in-vehicle networks. Various ECUs present inside the automotive transmits useful information via automotive multiplexing. Transmission of data in real-time achieves optimum functionality. The high bandwidth and high-speed requirement can be achieved either by using multiple buses or by implementing higher bandwidth. But, by doing so, the cost of the network as well as the complexity of the wiring increases. Another option is to implement higher layer protocol which can reduce the amount of data transferred by using data reduction (DR) techniques, thus reducing the bandwidth usage. The implementation cost is minimal as the changes are required in the software only and not in hardware.
Journal Article

Selection of Reference Flux Linkage for Direct Torque Control Based Induction Motor Drive in Electric Vehicle Applications

2019-04-08
Abstract The surge in economic activities, in the developing nations, has resulted in rapid expansion of urban centres. This expansion of cities has caused a rapid increase in vehicular traffic, which in turn has caused deterioration of air quality. To overcome the problem of unprecedented air pollution, the governments worldwide have framed policies for faster adoption of electric vehicles. One of the major challenges faced is the development of low- cost drive for these vehicles and keeping the imports to a minimum. As a result of this, the trend is to move away from the permanent magnet-based motor technology and to use induction motor-based drivetrain. For the induction motors to be successful in electric vehicle drivetrain application, it is important to have a robust speed control algorithm. This work aims at adapting a direct torque control technique for induction motor’s speed control.
X