Search Results

Abstract Gasoline particulate filters (GPFs) are important aftertreatment components that enable gasoline direct injection (GDI) engines to meet European Union (EU) 6 and China 6 particulate number emissions regulations for nonvolatile particles greater than 23 nm in diameter. GPFs are rapidly becoming an integral part of the modern GDI aftertreatment system. The Active Exhaust Tuning (EXTUN) Valve is a butterfly valve placed in the tailpipe of an exhaust system that can be electronically positioned to control exhaust noise levels (decibels) under various vehicle operating conditions. This device is positioned downstream of the GPF, and variations in the tuning valve position can impact exhaust backpressures, making it difficult to monitor soot/ash accumulation or detect damage/removal of the GPF substrate. The purpose of this work is to present a unique example of subsystem control and diagnostic architecture for an exhaust system combining GPF and EXTUN.

Abstract More than a decade ago, we proposed combined use of direct injection (DI) and jet ignition (JI) to produce high efficiency, high power-density, positive-ignition (PI), lean burn stratified, internal combustion engines (ICEs). Adopting this concept, the latest FIA F1 engines, which are electrically assisted, turbocharged, directly injected, jet ignited, gasoline engines and work lean stratified in a highly boosted environment, have delivered peak power fuel conversion efficiencies well above 46%, with specific power densities more than 340 kW/liter. The concept, further evolved, is here presented for unmanned aerial vehicle (UAV) applications. Results of simulations for a new DI JI ICE with rotary valve, being super-turbocharged and having gasoline or methanol as working fuel, show the opportunity to achieve even larger power densities, up to 430 kW/liter, while delivering a near-constant torque and, consequently, a nearly linear power curve over a wide range of speeds.

Abstract This article serves as a proof-of-concept and feasibility analysis regarding a variable compression ratio (VCR) engine design utilizing an exhaust valve opening during the compression stroke to vary the compression ratio instead of the traditional method of changing the cylinder or piston geometry patented by Ford, Mercedes-Benz, Nissan, Peugeot, Gomecsys, et al. [1]. In this concept, an additional exhaust valve opening was used to reduce the virtual compression ratio of the engine, without geometric changes. A computational fluid dynamic model in ANSYS Forte was used to simulate a single-cylinder, cold flow, four-stroke, direct injection engine cycle. In this model, the engine was simulated at a compression ratio of 10:1. Then, the model was modified to a compression ratio of 17:1. Then, an additional valve opening at the end of the compression stroke was added to the 17:1 high compression model.

Abstract The free piston linear generator (FPLG) is a novel machine that functions as an Auxiliary Power Unit (APU) for hybrid electric vehicles, which contains two opposed free piston engines and one linear generator between them. FPLG has attracted extensive interest for its potential advantages in terms of high power density and multi-fuel flexibility. The guarantee of FPLG generating electricity steadily and efficiently is the high controllability of compression ratio. In this article, a control-oriented discrete-time model was established based on Otto cycle. Since the fluctuation of in-cylinder pressure caused by instable fuel injection mass and combustion process is the main disturbance, a composite controller is designed to precisely control the compression ratio of FPLG. The composite controller is made up of a feedforward controller and a feedback tracking controller.

Abstract TOC

Abstract TOC

Abstract The principal issue in choosing an energy management strategy (EMS) for hybrid electric vehicles (HEVs) has been the way of determining the optimal share of electric energy in hybrid drive. In this article, a novel EMS is proposed that, along with maximum engine efficiency in the hybrid drive, can optimize the share of battery energy for the maximum efficiency of vehicle power train expanded with an imaginary power plant that, by delivering the electric energy to a grid, feeds the vehicle battery. It is proved that the expanded power train efficiency has the local maximum for a wide range of wheel power demand. The relation between the wheel power demand in hybrid drive, the share of battery energy, and the maximum efficiency of the expanded power train is conducted offline. Downloaded to the onboard control system, it enables the operation with the instantaneously optimal share of battery energy and the control system to operate with the low computational load.

Abstract Diesel trucks play a crucial role in transportation activity and a major contributor to fuel consumption and air pollution. To improve the energy efficiency of diesel trucks, we develop a truck eco-approach and departure (EAD) system based on Signal Phase and Timing (SPaT) message from signal controllers and road grade information along the path. The proposed model consists of two levels—the lower level for powertrain-based fuel consumption estimation and the upper level for optimal trajectory planning. The powertrain model is designed for a diesel engine with a six-gear transmission and well calibrated using on-board Electronic Control Unit (ECU) data. The trajectory planning model is formulated as a shortest path problem with the combination of time, distance, and speed as the state on each node and fuel consumption rate as the cost on state transition.

Abstract Regulations limiting GreenHouse Gases (GHG) from Heavy-Duty (HD) commercial vehicles in the United States (US) and European Union will phase in between the 2024 and 2030 model years. These mandates require efficiency improvements at both the engine and vehicle levels, with the most stringent reductions required in the heaviest vehicles used for long-haul applications. At the same time, a 90% reduction in oxides of nitrogen (NOx) will be required as part of new regulations from the California Air Resources Board. Any technologies applied to improve engine efficiency must therefore not come at the expense of increased NOx emissions. Research into advanced engine architectures and components has identified improved turbomachine efficiency as one of the largest potential contributors to engine efficiency improvement. However this comes at the cost of a reduced capability to drive high-pressure Exhaust Gas Recirculation (EGR).

Abstract The article describes the results achieved in developing a new diesel combustion system for passenger car application that, while capable of high power density, delivers excellent fuel economy through a combination of mechanical and thermodynamic efficiencies improvement. The project stemmed from the idea that, by leveraging the high fuel injection pressure of last generation common rail systems, it is possible to reduce the engine peak firing pressure (pfp) with great benefits on reciprocating and rotating components’ light-weighting and friction for high-speed light-duty engines, while keeping the power density at competitive levels. To this aim, an advanced injection system concept capable of injection pressure greater than 2500 bar was coupled to a prototype engine featuring newly developed combustion system. Then, the matching among these features has been thoroughly experimentally examined.

Abstract Insulating combustion chamber surfaces with thermal barrier coatings (TBCs) provides thermal efficiency improvement when done appropriately. This article reports on insulation heat transfer, engine performance characteristics, and damage modelling of “temperature swing” TBCs. “Temperature swing” insulation refers to the insulation material applied on surfaces of combustion chamber walls that enables selective manipulation of its surface temperature profile over the four strokes of an engine cycle. A combined GT Suite-ANSYS Fluent simulation methodology is developed to investigate the impact of thermal properties and insulation thickness for a variety of TBC materials for its “temperature swing” characteristics. This one-dimensional transient heat conduction analyses and engine cycle simulations are performed using scaled-down thermal properties of yttria-stabilized zirconia.

Abstract Higher water evaporation and proper water vapor distribution in the cylinder are very vital for improving emission and performance characteristics of water-injected engines. The concentration of water vapor should be higher and uniform near the walls of the combustion chamber and nil at the spark plug location. In direct water-injected engines, water evaporation, vapor distribution, and spray impingement are highly dependent on injector parameters, viz., water injector orientation (WIO), location, and spray angle. Therefore, in this article, a computational fluid dynamics (CFD) investigation is conducted to study the effects of water injector spray angle (WISA), and WIO on the water evaporation, emission, and performance characteristics of a four-stroke, wall-guided gasoline direct injection (GDI) engine. The WISA is varied from 10° to 35°, whereas the WIO is varied from 15° to 35° in steps of 5°.

Abstract Interactions between fuel sprays and stepped-lip diesel piston bowls can produce turbulent flow structures that improve efficiency and emissions, but the underlying mechanisms are not well understood. Recent experimental and simulation efforts provide evidence that increased efficiency and reduced smoke emissions coincide with the formation of long-lived, energetic vortices during the mixing-controlled portion of the combustion event. These vortices are believed to promote fuel-air mixing, increase heat-release rates, and improve air utilization, but they become weaker as main injection timing is advanced nearer to the top dead center (TDC). Further efficiency and emissions benefits may be realized if vortex formation can be strengthened for near-TDC injections. This work presents a simulation-based analysis of turbulent flow evolution within a stepped-lip combustion chamber.

Abstract Cycle-by-cycle combustion prediction in real time during engine operation can serve as a vital input for operating at optimal performance conditions and for emission control. In this work, a real-time capable physics-based combustion model has been proposed for the prediction of the heat release rate in a direct injection diesel engine. The model extends the approaches proposed earlier in the literature by considering spray dynamics such as spray penetration and Sauter mean diameter in order to calculate the mass of evaporated fuel from the spray. Wall impingement of the liquid spray is predicted by considering the liquid length based on the prevailing in-cylinder conditions. These effects are considered even after the hydraulic end of injection till the last droplet of fuel impinges on the combustion chamber wall. The fuel evaporated from the wall film and its contribution to the kinetic energy of the charge are also considered.

Abstract This experimental study aims to evaluate the engine performance and emissions when exhaust gas recirculation (EGR) and e-boosting are used in a gasoline compression ignition (GCI) engine operating at 2000 rpm and 800-900 kPa indicated mean effective pressure (IMEP) conditions. In an automotive size common-rail diesel engine architecture, a partially premixed charge-based GCI combustion was realized implementing triple injections with a split ratio of 50%, 10%, and 40% and injection timings of 170, 40, and 9-6 crank angle degrees (°CA) before top dead center (bTDC). The previous tests performed in the same engine suggested this injection strategy could achieve further nitrogen oxides (NOx) reduction if EGR is utilized with the help of intake air boosting to compensate for the loss in power output and engine efficiency. In the present study, the GCI engine is set up with a conventional EGR system and a supercharger driven by an electric motor (or an e-booster).

Abstract Diesel engines are an important technology for transportation of both people and goods. However, historically they have suffered a significant downside of high soot and nitrogen oxides (NOx) emissions. Recently, ducted fuel injection (DFI) has been demonstrated to attenuate soot formation in compression-ignition engines and combustion vessels by 50% to 100%. This allows for diesel engines to be run at low-NOx emissions that would have otherwise produced significantly more soot due to the soot/NOx tradeoff. Currently the root causes of this soot attenuation are not well understood. To be able to better optimize DFI for use across a variety of engines and conditions, it is important to understand clearly how it works. This study expands on the current understanding of DFI by using numerical modeling under nonreacting conditions to provide insights about the roles of entrainment and mixing that would have been much more challenging to obtain experimentally.

Abstract The article discusses the possibilities of detecting defects in the marine diesel engine injection system on a selected example. Basing on statistical data, it was pointed out that these engines had a significant failure rate in relation to the failure rate of other machinery and equipment used on ships. First, it concerns damage of the elements of the injection systems. Therefore, basing on the results of the authors’ own research, the possibility of improving diagnostic methods of the injection system that can be used in the ship operation process was pointed out. First, high diagnostic effectiveness of the analysis of pressure changes measured in the injection system was pointed out here. At the same time, taking into account the difficulties of such measurement in the conditions of the ship’s power plant, it has been shown that very good diagnostic effects can be obtained by using indicator diagrams to calculate heat release characteristics.

Abstract Diesel engines include systems for cooling, lubrication, and fuel injection and contain a variety of components. A malfunction in any of the engine systems or the presence of any faulty element influences engine performance and deteriorates its components. This research is concerned with the untimely appearance of vital cracks in the liners of a turbocharged heavy-duty Diesel engine. To find the root causes for premature failure, rigorous examinations through visual observations, material characterization, and metallographic investigations are performed. These include Scanning Electron Microscope (SEM) and Energy-Dispersive Spectroscopy (EDS), fracture mechanics analysis, and performance examination, which are also followed by Finite Element Moldings. To find the proper remedy to resolve the problem, drawing a precise and reliable picture of the engine’s operating conditions is required.

Abstract In recent years, several innovative diesel combustion systems were developed and optimized in order to enhance the air and injected fuel mixing for engine efficiency improvements and to mitigate the formation of fuel-rich regions for soot emissions reduction. With these aims, a three-dimensional computational fluid dynamics (3D-CFD) numerical study was carried out in order to evaluate the impact of three different piston bowl geometries on a passenger car four-cylinder diesel engine, 1.6 liters. Once the numerical model was validated considering the baseline re-entrant bowl, two innovative bowl geometries were defined: one based on the stepped-lip bowl; the other including a number of radial bumps equal to the nozzle holes number. Firstly, the rated power engine operating condition was investigated under nonreacting conditions to evaluate the piston bowl effects on the in-cylinder mixing.

Abstract Recent research has demonstrated that gasoline compression ignition (GCI) can improve the soot-oxides of nitrogen (NOx) trade-off of conventional diesel engines due to the beneficial properties of light distillate fuels. In addition to air handling and aftertreatment, fuel systems also require further development to realize the potential efficiency and emissions benefits of GCI. Injector one-dimensional (1-D) hydraulic modeling is an important design tool used for this purpose. The current study is a continuation of prior work that used computed physical fuel properties and hydraulic models to accurately simulate high-pressure injection behavior relevant to GCI. With respect to fuel characteristics for the model, physical properties were validated by direct comparison to measurements at temperatures and pressures reaching 150°C and 2500 bar, respectively.