Search Results

Abstract The transient surface pressure over a full-scale, operational compact automotive vehicle—a Volkswagen Golf 7—exposed to transient crosswinds with relative yaw angles of β = 22-45° has been characterized. Experiments were performed at the BMW side-wind facility in Aschheim, Germany. Measurements of the incoming flow in front of the car were taken with eleven five-hole dynamic pressure probes, and separately, time-resolved surface pressure measurements at 188 locations were performed. Unsteady characteristics (not able to be identified in quasi-steady modelling) have been identified: the flow in separated regions on the vehicle’s leeward side takes longer to develop than at the windward side, and spatially, the vehicle experiences local crosswind as it gradually enters the crosswind.

Abstract A computational fluid dynamics (CFD) and wind tunnel investigation of a human powered vehicle (HPV), designed by the Velo Racing Team at Ostfalia University, is undertaken to analyse the Eco-body’s drag efficiency. Aimed at competing in a high profile HPV speed record competition, the vehicle’s aerodynamic efficiency is shown to compare well with successful recent eco-body designs. Despite several limitations, newly obtained wind tunnel data shows that the corresponding CFD simulations offer an effective tool for analysing and refining the HPV design. It is shown that, in particular, the design of the rear wheel fairings, as well as the ride height of the vehicle, may be optimised further. In addition, refinements to the CFD and wind tunnel methodologies are recommended to help correlation.

Abstract A novel use of state estimation methods as initial input for a landing response analysis is proposed in this work. Six degrees of freedom (DOF) non-linear landing response model is conceived by considering longitudinal dynamics of aircraft as a rigid body with heave-and-pitch motions coupled onto a bicycle landing gear † arrangement. The DOF for each landing gear consist of vertical and longitudinal motions of un-sprung mass, considering strut bending flexibility. The measurement data for state estimation is obtained for three landing cases using non-linear flight mechanics model interfaced with pilot-in-loop simulation. State estimation methods such as Upper Diagonal Adaptive Extended Kalman Filter (UD-AEKF) with fuzzy-based adaptive tuning and Un-scented Kalman Filter (UKF) were adapted for landing maneuver problem. On the basis of estimation error metrics, aircraft state from UKF is considered during onset of touchdown.

Abstract From the fact that a propulsor consumes less power for a given thrust if the inlet air is slower, simulations are conducted for a propulsor imposed behind an airfoil as ideal boundary layer ingestion (BLI) propulsor to stand on the benefits of this configuration from the point of view of power and efficiency and to get a closer look on the mutual interaction between them. This interaction is quantified by the impact on three main sets of parameters, namely, power consumption, boundary layer properties, and airfoil performance. The position and size of the propulsor have great influence on the flow around the airfoil. Parametric studies are carried out to understand their influence. BLI propulsor directly affects the power saving and all of the pressure-dependent parameters, including lift and drag. For the present case, power saving reached 14.4% compared to the propeller working in freestream.

Abstract A flight envelope for aircraft performance in the vertical plane illustrates the performance limitations on the aircraft, usually indicating the minimum and maximum airspeeds at a given altitude, the airspeeds for maximum rate of climb and maximum angle of climb at a given altitude, and the maximum altitude or absolute ceiling of the aircraft. This study outlines the procedure for constructing a vertical-plane flight performance aircraft for an aircraft with a fixed-pitch propeller, which involves additional complexities due to the variable propeller efficiency. The propeller performance, engine power, and drag polar models are described, as is the computational procedure. Envelopes for the flight performance in the vertical plane are presented for a particular remotely-piloted aircraft at different take-off weights.

Abstract Improving the aerodynamics of heavy trucks is an important consideration in the strive for more energy-efficient vehicles. Cooling drag is one part of the total aerodynamic resistance acting on a vehicle, which arises as a consequence of air flowing through the grille area, the heat exchangers, and the irregular under-hood area. Today cooling packages of heavy trucks are dimensioned for a critical cooling case, typically when the vehicle is driving fully laden, at low speed up a steep hill. However, for long-haul trucks, mostly operating at highway speeds on mostly level roads, it may not be necessary to have all the cooling airflow from an open-grille configuration. It can therefore be desirable for fuel consumption purposes, to shut off the entire cooling airflow, or a portion of it, under certain driving conditions dictated by the cooling demands. In Europe, most trucks operating on the roads are of cab-over-engine type, as a consequence of the length legislations present.

Abstract An investigation into the capability of passive porosity to reduce the drag of a bluff-body is presented. This initial work involves integrating varying degrees of porosity into the side and back faces of a small-scale model to determine optimum conditions for maximum drag reduction. Both force and pressure measurements at differing degrees of model yaw are presented, with the conditions for optimum performance, identified. At a length-based Reynolds number of 2.3 × 106, results showed a maximum drag reduction of 12% at zero yaw when the ratio of the open area on the back face relative to the side faces was between two and four. For all non-zero yaw angles tested, this ratio reduced to approximately two, with the drag benefit reducing to 6% at 10.5 degrees. From a supplementary theoretical analysis, calculated optimum bleed rate into the base for maximum drag reduction, also showed reasonable agreement to other results reported previously.

Abstract This paper presents a combined aero-thermal computational fluid dynamic (CFD) evaluation of platooning medium duty commercial vehicles in two highway configurations. Thermal analysis comparison is made between an approach that includes vehicle drag reduction on engine heat rejection and one that does not by assuming a constant heat rejection based on open road conditions. The paper concludes that accounting for aerodynamic drag reduction on engine heat load provides a more real world evaluation than assuming a constant heat load based on open road conditions. A 3D CFD underhood thermal simulations are performed in two different vehicle platooning configurations; (i) single-lane and (ii) two-lane traffic conditions. The vehicle platooning consists of two identical vehicles, i.e. leading and trailing vehicle. In this work, heat exchangers are modeled by two different heat rejection rate models.

Abstract A two-dimensional model of three elements, high-lift airfoil, was designed at a Reynolds number of ?????? using computational fluid dynamics (CFD) to generate downforce with good lift-to-drag efficiency for a formula student open-wheel race car basing on the nominal track speeds. The numerical solver uses the Reynolds-averaged Navier-Stokes (RANS) equation model coupled with the Langtry-Menter four-equation transition shear stress transport (SST) turbulence model. Such model adds two further equations to the ?? − ?? SST model resulting in an accurate prediction for the amount of flow separation due to adverse pressure gradient in low Reynolds number flow. The ?? − ?? SST model includes the transport effects into the eddy-viscosity formulation, whereas the two equations of transition momentum thickness Reynolds number and intermittency should further consider transition effects at low Reynolds number.

Abstract The study of road loads on trucks plays a major role in assessing the effect of heavy-vehicle design on fuel conservation measures. Coastdown testing with full-scale vehicles in the field offers a good avenue to extract drag components, provided that random instrumentation faults and biased environmental conditions do not introduce errors into the results. However, full-scale coastdown testing is expensive, and environmental biases which are ever-present are difficult to control in the results reduction. Procedures introduced to overcome the shortcomings of full-scale field testing, such as wind tunnels and computational fluid dynamics (CFD), though very reliable, mainly focus on estimating the effects of aerodynamic drag forces to the neglect of other road loads which should be considered.

Abstract When commercial vehicles drive in a mountainous area, the complex road condition and long slopes cause frequent acceleration and braking, which will use 25% more fuel. And the brake temperature rises rapidly due to continuous braking on the long-distance downslopes, which will make the brake drum fail with the brake temperature exceeding 308°C [1]. Meanwhile, the kinetic energy is wasted during the driving progress on the slopes when the vehicle rolls up and down. Our laboratory built a model that could calculate the distance from the top of the slope, where the driver could release the accelerator pedal. Thus, on the slope, the vehicle uses less fuel when it rolls up and less brakes when down. What we do in this article is use this model in a real vehicle and measure how well it works.

Abstract This article analyses the flow field between two 1/8-scale Generalized European Transport System (GETS) models which are placed in a two-vehicle platoon at close distances. Numerical simulations using the lattice Boltzmann method together with a wind tunnel experiment (open jet facility, OJF) were executed. Next, to balance measurements, coaxial volumetric velocimetry (CVV) measurements were performed to obtain information about the flow field. Three intervehicle distances, 0.10, 0.45 and 0.91 times the vehicle length, were tested for various platoon configurations where the vehicles in the platoon varied in terms of front-edge radius and the addition of tails. At the smallest intervehicle distance, the greatest reductions in drag were found for both the leading and trailing vehicles. The flow in the gap between the two vehicles follows an S-shaped path with small variations between the configurations.

Abstract In this study, two types of drag reduction devices (a horizontal plate, and a vertical plate) are used to weaken the downwash of the upper flow and c-pillar vortex of the DrivAer notchback model driving at high speed (140 km/h). By analyzing and comparing 15 cases in total, the aerodynamic drag reduction mechanism can be used in the development of vehicles. First, various CFD simulation conditions of a baseline model were compared to determine the analysis condition that efficiently calculates the correct aerodynamic drag. The vertical plate and horizontal plate applied in the path of the c-pillar vortex and downwash suppressed vortex development and induced rapid dissipation. As a result, the application of a 50-mm wedge-shaped vertical plate to the trunk weakened the vortex and reduced the drag by 3.3% by preventing the side flow from entering the trunk top.

Abstract Sports Utility Vehicles (SUVs) often have blunt rear end geometries for design and practicality, which is not typically aerodynamic. Drag can be reduced with a number of passive and active methods, which are generally prioritised at zero yaw, which is not entirely representative of the “on road” environment. As such, to combine a visually square geometry (at rest) with optimal drag reductions at non-zero yaw, an adaptive system that applies vertical side edge tapers independently is tested statically. A parametric study has been undertaken in Loughborough University’s Large Wind Tunnel with the ¼ scale Windsor Model. The aerodynamic effect of implementing asymmetric side tapering has been assessed for a range of yaw angles (0°, ±2.5°, ±5° and ±10°) on the force and moment coefficients.

Abstract Aerodynamic optimization of the exterior vehicle shape is a highly multidisciplinary task involving, among others, styling and aerodynamics. The often differing priorities of these two disciplines give rise to iterative loops between stylists and aerodynamicists. Reduced-order modeling (ROM) has the potential to shortcut these loops by enabling aerodynamic evaluations in real time. In this study, we aim to assess the performance of ROM via proper orthogonal decomposition (POD) for a real-life industrial test case, with focus on the achievable accuracy for the prediction of fields and aerodynamic coefficients. To that end, we create a training data set based on a six-dimensional parameterization of a Volkswagen passenger production car by computing 100 variants with Detached-Eddy simulations (DES).

Abstract This article presents the application of the Enhanced Sequence Diagram (ESD) for the analysis of the functionality of a system with shape-changing aspects in the context of its multiple operational modes, considering an active real spoiler as a case study. The article provides new insights on the ESD support for model-based capture and articulation of functional requirements across multiple operation modes of the same system, with appropriate detail on attributes and metrics, and the alignment of these attributes and metrics in line with the concept of time through scope lines. The article also provides a comprehensive argument and discussion, exemplified based on the case study, for the support that the ESD provides for early systems functional and architecture analysis, within the context of a broader model-based Failure Mode Analysis methodology.

Abstract A wind-tunnel study was undertaken to investigate the drag reduction potential of two-truck platooning, in the context of understanding some of the factors that may influence the potential fuel savings and greenhouse-gas reductions. Testing was undertaken in the National Research Council Canada 2 m × 3 m Wind Tunnel with two 1/15-scale models of modern aerodynamic tractors paired with dry-van trailers configured with and without combinations of side-skirts and boat-tails. Separation distances of 0.14, 0.28, 0.49, 0.70 and 1.04 vehicle lengths were tested (3 m, 6 m, 10.5 m, 15 m, and 22.5 m full scale). Additionally, within-lane lateral offsets up to 0.31 vehicle widths (0.8 m full scale) were evaluated, along with a full-lane offset of 1.42 vehicle widths (3.7 m full scale). This study has made use of a wind-averaged-drag coefficient as the primary metric for evaluating the effect of vehicle platooning.

Abstract Fuel consumption is at an all-time high, with crude oil set to get depleted in the next two decades. Drag force is one of the major components responsible for decreasing mileage and thus increasing fuel consumption in vehicles. Using passive modifications such as spherical depressions on the body surface, aerodynamic drag experienced by passenger vehicles can be significantly reduced. Spherical depressions are designed to delay flow separation, following which the wake size is reduced, resulting in a decrease in drag force. In this study, computer-aided design (CAD) models of generalized lightweight vehicles are made with dimples at the sides of the car, having a diameter of 60 mm and a center-to-center distance of 90 mm. Several models are created having depression aspect ratios (ARs) of 2, 4, 6, and 8, and each model is simulated to velocities of 22 m/s, 24 m/s, 26 m/s, 28 m/s, and 30 m/s.

Abstract The development of the technology of automated highways promises the opportunity for the vehicles to travel safely at a closer distance concerning each other. As such, vehicles moving in the wake of others experience a reduction in fuel consumption. This article investigates the effect of longitudinal distance between two passenger cars on drag coefficients numerically and experimentally. For the numerical analysis, the fluid flow at car speeds of 70, 90 and 110 km/h were examined. The Artificial Intelligence coding was applied to train an Artificial Neural Network to extend the calculated data. The optimum values for the inter-vehicle distance and the vehicle speed to assure the least drag coefficient are obtained. To support the numerical results an instrument designed and built particularly to accurately measure the fuel consumption was installed on a midsize sedan car and some field tests were carried out.

Abstract TOC