Search Results

Abstract The prediction of mechanical elastic response of laminated hybrid polymer composites with basic carbon nanostructure, that is carbon nanotubes and graphene, inclusions has gained importance in many advanced industries like aerospace and automotive. For this purpose, in the current work, a hierarchical, four-stage, multilevel framework is established, starting from the nanoscale, up to the laminated hybrid composites. The proposed methodology starts with the evaluation of the mechanical properties of carbon nanostructure inclusions, at the nanoscale, using advanced 3D spring-based finite element models. The nanoinclusions are considered to be embedded randomly in the matrix material, and the Halpin-Tsai model is used in order to compute the average properties of the hybrid matrix at the lamina micromechanics level.

Abstract Dynamic stresses exist in parts of a catalyst muffler caused by the vibration of a moving vehicle, and it is important to clarify and predict the vibration response properties for preventing fatigue failures. Assuming a vibration isolating installation in the vehicle frame, the vibration transmissibility and local dynamic stress of the catalyst muffler were examined through a vibration machine. Based on the measured data and by systematically taking vibration theories into consideration, a new prediction method of the vibration modes and parameters was proposed that takes account of vibration isolating and damping. A lumped vibration model with the six-element and one mass point was set up, and the vibration response parameters were analyzed accurately from equations of motion. In the vibration test, resonance peaks from the hanging bracket, rubber bush, and muffler parts were confirmed in three excitation drives, and local stress peaks were coordinate with them as well.

Abstract Effects of process parameters such as rotational speed, feed rate, and drill diameters on the drilling behavior of basalt-epoxy-based composites including 2.5 wt.% Al2O3 particles manufactured by mixing and compression method were investigated by Taguchi’s technique. The experimental results showed that the burr height (BH) increased considerably almost linearly with an increase in the drill diameter, while it remained stable with speed and decreased the feed rate slightly. There was an excellent correlation between the control factors and responses, BH of basalt fiber-reinforced plastics (BFRPs) through the Taguchi approach. The model had an adjusted R2 value of 96.3%. Generally, the inclusion of Al2O3 particles in BFRP increased its cutting force properties. Optimized drilling conditions for the input variables to produce the lowest response of the BH for composites were rotational speed of 560 rpm and feed rate of 0.28 mm/rev and a drill diameter of 4.5 mm.

Abstract The high quality of the machined parts in a short time is a research challenge for enhancing these parts’ operating performance. Optimizing the machining operations and adequately selecting the cutting parameters can solve this challenge. Thus, this work proposes an optimization approach of the machining process parameters of epoxy hybrid nanocomposites reinforced by multiwall carbon nanotubes (MWCNTs) and aluminum oxide (Al2O3). Cutting speed (V), feed rate (F), insert nose radius, and depth of cut (D) were the machining parameters. The roundness error and surface roughness (Ra) were selected as process response control parameters. The optimization techniques such as response surface method (RSM) and grey relation analysis (GRA) with the variance of analysis (ANOVA) were involved. Forty experimental runs were performed. The RSM optimization and ANOVA results showed that the insert nose radius and F are the most significant factors that affect the Ra.

Abstract The paper presents a complete description of the design and manufacturing of a Carbon Fiber/epoxy mold with an embedded Carbon Fiber resistor heater, and the mold performances in terms of its surface temperature distribution and thermal deformations resulting from the heating. The mold was designed for manufacturing aileron skins from Vacuum Bag Only prepreg cured at 135°C. The glass transition temperature of the used resin-hardener system was about 175°C. To ensure homogenous temperature of the mold working surface in the course of curing, the Carbon Fiber heater was embedded in a layer of a highly heat-conductive cristobalite/epoxy composite, forming the core of the mold shell. Because the cristobalite/epoxy composite displayed much higher thermal expansion than CF/epoxy did, thermal stresses could arise due to this discrepancy in the course of heating.

Abstract Due to the high deformability and energy dissipation capacity of polymer foams in compression, they are used in automotive applications to mitigate mechanical impacts. The mechanical response of the foams is strongly affected by their density. Phenomenological relations have been proposed to describe the effect of foam density on their stress-strain response in compression at a fixed loading rate and the effect of loading rate at a fixed foam density. In the present work, these empirical approaches are combined allowing for the dependence of loading rate effect in compression on foam density. The minimum experimental data set for calibration of the proposed model consists of compression test results at two different loading rates of foams with two different densities.

Mechanical and thermal properties of the rubber compounds of a tire play an important role in the overall performance of the tire when it is in contact with the terrain. Although there are many studies conducted on the properties of the rubber compounds of the tire to improve some of the tire characteristics, such as the wear of the tread, there are a limited number of studies that focused on the performance of the tire when it is in contact with ice. This study is a part of a more comprehensive project looking into the tire-ice performance and modeling. In this study, to understand the effect of different rubber compounds on the tire performance, three identical tires from the same company have been chosen. The tires’ only difference is the material properties of the rubber. Two approaches have been implemented in this study.

Abstract Addition of hydrogen to hydrocarbons in premixed turbulent combustion is of technological interest due to their increased reactivity, flame stability and extended lean extinction limits. However, such flames are a challenge to reaction modelling, especially as the strong preferential diffusion effects modify the physical processes, which are of importance even for highly turbulent high-pressure conditions. In the present work, Reynolds-averaged Navier-Stokes (RANS) modelling is carried out to investigate pressure and hydrogen content on methane/hydrogen/air flames.

Abstract Direct dual fuel stratification (DDFS) strategy benefits the advantages of the RCCI and PPC strategies simultaneously. DDFS has improved control over the heat release rate, by injecting a considerable amount of fuel near TDC, compared to RCCI. In addition, the third injection (near TDC) is diffusion-limited. Consequently, piston bowl geometry directly affects the formation of emissions. The modified piston geometry was developed and optimized for RCCI by previous scholars. Since all DDFS experimental tests were performed with the modified piston profile, the other piston profiles need to be investigated for this strategy. In this article, first, a comparative study between the three conventional piston profiles, including the modified, stock, and scaled pistons, was performed. Afterward, the gasoline injector position was shifted to the head cylinder center for the stock piston. NOX emissions were improved; however, soot was increased slightly.

Abstract TOC

Abstract Electrostatic discharge during aircraft refueling operations has long been recognized as a safety hazard. To reduce the chances of this happening, different practices were developed, the most common being the addition of a static dissipator additive (SDA). Nowadays, the SDA is a well-established requirement in all the leading jet-fuel specifications and is in widespread use in commercial and military aviation industries. To deepen the understanding of the electrostatic behavior of nonconductive jet fuel and SDA, the Israeli Air Force (IAF) has conducted small-scale refueling tests in a simulated aircraft fuel tank. In these tests, the effect of flow rate, residence time, SDA concentration, bounding, grounding, and the method of filling were evaluated by measuring the electrostatic field strength generated. The simulation of the aircraft fuel tank was obtained using a nonconductive plastic tank jointed with a small faucet at the bottom.

Abstract Single point incremental forming (SPIF) is a sheet forming technology giving low volume production with high flexibility characteristics. The flexibility of the process is mainly related to the fact that incremental forming does not require a dedicated die to operate as compared to other forming processes. Polymers are extensively used for many applications because of their good mechanical properties. Considerable research has been reported for the SPIF of metals, but the researches on polymers are in scarce. In the present work, SPIF is performed on one of the polymers known as polyvinyl chloride. The effect of wall angle, feed rate, and step size on springback, thinning, and surface roughness is observed. It was found that the springback mainly depends on the wall angle but it is least dependent on the feed rate. The thinning and the surface roughness also mainly depend on the wall angle but are least dependent on step size.

Abstract Climate change has necessitated the development of “green” alternatives to replace existing materials. This focus has resulted in the push toward fabricating natural fiber-reinforced polymer composites. This research work looks at the surface roughness (SR) of natural fibers like rice husk ash (RHA) and groundnut shell ash (GSA) reinforced in nine different concentrations into an epoxy matrix to form composites. Composite samples are fabricated using various concentrations of natural fibers and measures and optimizes for the SR through the implementation of genetic algorithms (GA). It was found that a minimum SR of 1.422 μm can be obtained for an epoxy/hardener ratio of 3:1 and without the addition of any reinforcements. This optimization was achieved within 102 generations. In addition to GA optimization, another optimization implementation was done through the Taguchi method.

Abstract This work presents a numerical study of the performance and nitrogen oxides (NOx) emissions of a conventional ethanol engine converted to work as a flex-fuel nonconventional architecture: the Split-Cycle Engine (SCE). For this study, the conventional engine fueled with hydrous ethanol was modeled and validated with data from experimental tests. Then the model was converted to operate as an SCE with two compressors and two expanders and simulated with a progressive downsizing of the compressors of the SCE. When the swept volume of the compressors was reduced to 87% of that of the expanders, the thermal conversion efficiency increased by 3.3%. Because of this, the downsized SCE was submitted to simulation runs using two different fuels: hydrous ethanol (H100) and an indolene-ethanol blend (H85). The results of the simulations were compared to the experimental results of the conventional engine.

Abstract The main aim of this study is to understand the effect of thermal conditions on the fatigue resistance of one automotive Daytime Running Lamp (DRL) housing made of Polycarbonate (PC) material. Automotive lighting products are made of mostly thermoplastic materials. Thermoplastic materials have mechanical properties varying significantly by temperature. As a result, thermal conditions at service life must be considered before evaluating the mechanical performance of automotive lighting products. In this study, thermal finite element analysis (FEA) has been done in order to understand the temperature distribution on DRL components at different thermal environments. Thermal map files representing the temperature distributions of the DRL components have been extracted and entered as load inputs into the modal FEA to find out the resonance frequencies. Using material properties varying by temperature, resonance frequencies of the DRL have been found by modal analysis and compared.

Abstract Aircraft lift bag is the equipment used for the recovery of an aircraft and is considered as a lifting equipment. Boeing 737 is a domestic aircraft considered for designing this bag. The aircraft lift bag is made of composite material, and the most widely used materials are nylon and neoprene. A composite material is used to make the bag lightweight and easy to handle. For calculation of properties and the engineering constant of the respective composite materials, micromechanics approach is used, in which the method of Representative Volume Element (RVE) is taken into consideration. The loading and boundary conditions are the exact replica of the working conditions. The operation of this bag is completely pneumatic. The stresses induced in the bag are analyzed in finite element software and are compared with the calculated theoretical values. CATIA is used to model the bag, and ABAQUS is used for the finite element calculations.

Abstract TOC

Abstract Directional drilling rigs and hydraulic stimulation equipment typically use diesel fueled compression ignition (CI) engines. The majority of these engines are compliant with US Environmental Protection Agency (EPA) Tier 2 standards. To reduce fuel costs, industry is investing in dual fuel (DF) and dedicated natural gas (DNG) engines. DF engines use diesel oxidation catalysts (DOCs) to reduce CO and NMHC emissions. DNG engines may be either lean-burn or rich-burn and the latter uses three-way catalysts (TWC) to reduce CO, NMHC, and NOx emissions. This research presents in-use catalyst efficiency data collected pre- and post-catalyst for three DF engines and two DNG engines. One DF engine was converted earlier and did not include a DOC. Data were collected from six Tier 2 engines, two CI drilling engines converted to operate as DF, two CI hydraulic fracturing engines converted to operate as DF, and two SI DNG drilling engines.

Abstract The rapid utilization of fossil fuels has triggered the finding of alternative renewable fuel that replaces or reduces the consumption by alternative fuels for fueling compression ignition (CI) engines. One such renewable fuel is ethanol which can be manufactured from biomass. The present study details the utilization of an optimum amount of ethanol in CI engine by modifying the operating parameters. It was already published in the previous paper that 45% ethanol can be utilized along with diesel using 10% butanol as cosolvent. This fuel is also meeting the minimum requirement with respect to properties as per ASTM standards. This experimental study was performed to investigate the influence of modifying the engine operating parameters on the performance, combustion, and emission parameters fueled with the blend containing 45% ethanol under various load conditions.

Abstract To overcome the limitations such as lower combustion efficiency (CE) and higher cyclic variability in methanol/diesel (M/D) reactivity controlled compression ignition (RCCI) combustion, a fuel having higher reactivity than diesel (i.e., polyoxymethylene dimethyl ethers, PODE) was used in our previous study. Methanol/PODE RCCI combustion resulted in improved CE and reduction in soot and unburned emissions compared to M/D RCCI combustion. However, it was noticed that the use of neat PODE as high-reactivity fuel had damaged the fuel line materials frequently due to its higher oxygen content and lower viscosity. In addition, Methanol/PODE RCCI has also resulted in higher NO emissions compared to M/D RCCI combustion.