Search Results

An experimental study was conducted on a spark-ignited direct-injection engine burning fuels with different evaporation and autoignition characteristics. The test engine was a single-cylinder Direct-Injection Stratified-Charge (DISC) engine incorporating a combustion process similar to the Texaco Controlled Combustion System. Two fuels were tested and compared with a baseline gasoline fuel: diesel fuel, and gasoline mixed with an ignition improver. The tests were done at low to medium engine loads. Diesel fuel was found to have similar levels of hydrocarbon (HC) emissions as gasoline but had different characteristics. The optimum timing for diesel fuel was retarded from that for gasoline and combustion variability was much less with diesel than with gasoline. Gasoline with a commercial ignition improver normally used to increase the cetane number of diesel fuel was also tested. The effect of changing the autoignition quality of the fuel depended on the injector used.

In the study of internal combustion engines, gas temperatures within the system are of significant importance. The adverse conditions under firing operation, however, make measurements by any means very difficult. This current study seems to have gone the farthest to date for velocity of sound gas temperature measurements in internal combustion engine applications. An ultrasound signal is sent by a transmitting transducer, through the gas medium, and into the receiving transducer. The received signal is recorded, and the gas temperature determined from the time of flight. In-cylinder and exhaust manifold gas temperatures under fired conditions are presented, and are all consistent. Impacts of operating parameters like mixture equivalence ratio and coolant temperature are investigated.

Previous research has shown the potential benefits of running an engine with excess air. The challenges of running lean have also been identified, but not all of them have been fundamentally explained. Under high dilution levels, a lean limit is reached where combustion becomes unstable, significantly deteriorating drivability and engine efficiency, thus limiting the full potential of lean combustion. This paper expands the understanding of lean combustion by explaining the fundamentals behind this rapid rise in combustion variability and how this instability can be reduced. A flame entrainment combustion model was used to explain the fundamentals behind the observed combustion behavior in a comprehensive set of lean gasoline and hydrogen-enhanced cylinder pressure data in an SI engine. The data covered a wide range of operating conditions including different compression ratios, loads, types of dilution, fuels including levels of hydrogen enhancement, and levels of turbulence.

For some time, spatial nonuniformities in the unburned mixture within a spark ignition engine have been suspected of contributing to cycle-by-cycle variations in combustion. In this work, an experimental structure was developed that allowed the effects of fuel/air nonuniformity and residual gas/fresh charge nonuniformity to be separately addressed, with special regard given to their impact on the flame development process and combustion rate. Under the conditions of light loads and low speed, it was found that a decrease in fuel-air nonuniformity caused a slight reduction in the variation of the early flame development angle but had no significant impact on the statistics of the main combustion phase or IMEP. Eliminating residual gas nonuniformity by skip firing the engine and adding equivalent residual to the fresh mixture prior to entry to the cylinder had no detectable impact on the flame development process.

The oil control ring is the most critical component for oil consumption and friction from the piston system in internal combustion engines. Three-piece oil control rings are widely used in Spark Ignition (SI) engines. However, the dynamics and lubrication of three piece oil control rings have not been thoroughly studied from the theoretical point of view. In this work, a model was developed to predict side sealing, bore sealing, friction, and asperity contact between rails and groove as well as between rails and the liner in a Three Piece Oil Control Ring (TPOCR). The model couples the axial and twist dynamics of the two rails of TPOCR and the lubrication between two rails and the cylinder bore. Detailed rail/groove and rail/liner interactions were considered. The pressure distribution from oil squeezing and asperity contact between the flanks of the rails and the groove were both considered for rail/groove interaction.

Experiments were conducted to determine the effects of substantial spark retard on combustion, hydrocarbon (HC) emissions, and exhaust temperature, under cold engine conditions. A single-cylinder research engine was operated at 20° C fluid temperatures for various spark timings and relative air/fuel ratios. Combustion stability was observed to decrease as the phasing of the 50% mass fraction burned (MFB) occurred later in the expansion stroke. A thermodynamic burn rate analysis indicated combustion was complete at exhaust valve opening with -20° before top dead center (BTDC) spark timings. Chemical and thermal energy of the exhaust gas was tracked from cylinder-exit to the exhaust runner. Time-resolved HC concentrations measured in the port and runner were mass weighted to obtain an exhaust HC mass flow rate. Results were compared to time averaged well downstream HC levels.

Experiments to study the effects of oxygenated fuels on emissions and combustion were performed in a single-cylinder direct-injection (DI) diesel engine. A matrix of oxygen containing fuels assessed the impact of weight percent oxygen content, oxygenate chemical structure, and oxygenate volatility on emissions. Several oxygenated chemicals were blended with an ultra-low sulfur diesel fuel and evaluated at an equivalent energy release and combustion phasing. Additional experiments investigated the effectiveness of oxygenated fuels at a different engine load, a matched fuel/air equivalence ratio, and blended with a diesel fuel from the Fischer-Tropsch process. Interactions between emissions and critical engine operating parameters were also quantified. A scanning mobility particle sizer (SMPS) was used to evaluate particle size distributions, in addition to particulate matter (PM) filter and oxides of nitrogen (NOx) measurements.

A thermodynamic based cycle simulation which uses a thermal boundary layer, either, a fully mixed or layered adiabatic core, and a crevice combustion inefficiency routine has been used to explore the sensitivity of NO concentration predictions to critical physical modeling assumptions. An experimental database, which included measurements of residual gas fraction, was obtained from a 2.0 liter Nissan engine while firing on propane. A model calibration methodology was developed to ensure accurate predictions of in-cylinder pressure and burned gas temperature. Comparisons with experimental NO data then showed that accounting for temperature stratification during combustion with a layered adiabatic core and including a crevice/combustion inefficiency routine, improved the match of modeling predictions to data, in comparison to a fully mixed adiabatic core.

An experimental study was performed to investigate the effects of various intake charge motion control valves (CMCVs) on mixture preparation, combustion, and hydrocarbon (HC) emissions during the cold start-up process of a port fuel injected spark ignition (SI) engine. Different charge motions were produced by three differently shaped plates in the CMCV device, each of which blocked off 75% of the engine's intake ports. Time-resolved HC, CO and CO2 concentrations were measured at the exhaust port exit in order to achieve cycle-by-cycle engine-out HC mass and in-cylinder air/fuel ratio. Combustion characteristics were examined through a thermodynamic burn rate analysis. Cold-fluid steady state experiments were carried out with the CMCV open and closed. Enhanced charge motion with the CMCV closed was found to shorten the combustion duration, which caused the location of 50% mass fraction burned (MFB) to occur up to 5° CA earlier for the same spark timing.

In an effort to both increase engine efficiency and generate new, consistent, and reliable data useful for the development of engine concepts, a modern single-cylinder 4-valve spark-ignition research engine was used to determine the response of indicated engine efficiency to combustion phasing, relative air-fuel ratio, compression ratio, and load. Combustion modeling was then used to help explain the observed trends, and the limitations on achieving higher efficiency. This paper analyzes the logic behind such gains in efficiency and presents correlations of the experimental data. The results are helpful for examining the potential for more efficient engine designs, where high compression ratios can be used under lean or dilute regimes, at a variety of loads.

A set of experiments was performed to investigate the effects of relative air-fuel ratio, inlet boost pressure, and compression ratio on engine knock behavior. Selected operating conditions were also examined with simulated hydrogen rich fuel reformate added to the gasoline-air intake mixture. For each operating condition knock limited spark advance was found for a range of octane numbers (ON) for two fuel types: primary reference fuels (PRFs), and toluene reference fuels (TRFs). A smaller set of experiments was also performed with unleaded test gasolines. A combustion phasing parameter based on the timing of 50% mass fraction burned, termed “combustion retard”, was used as it correlates well to engine performance. The combustion retard required to just avoid knock increases with relative air-fuel ratio for PRFs and decreases with air-fuel ratio for TRFs.

This paper explores the modeling of a lean boosted engine concept. Modeling provides a useful tool for investigating different parameters and comparing resultant emissions and fuel economy performance. An existing architectural concept has been tailored to a boosted hydrogen-enhanced lean-burn SI engine. The simulation consists of a set of Matlab models, part physical and part empirical, which has been developed to simulate a working engine. The model was calibrated with production engine data and experimental data taken at MIT. Combustion and emissions data come from a single cylinder research engine and include changes in air/fuel ratio, load and speed, and different fractions of the gasoline fuel reformed to H2 and CO. The outputs of the model are brake specific NOx emissions and brake specific fuel consumption maps along with cumulative NOx emissions and fuel economy for urban and highway drive cycles.

This paper provides an overview of spark-ignition engine unburned hydrocarbon emissions mechanisms, and then uses this framework to relate measured engine-out hydrocarbon emission levels to the processes within the engine from which they result. Typically, spark-ignition engine-out HC levels are 1.5 to 2 percent of the gasoline fuel flow into the engine; about half this amount is unburned fuel and half is partially reacted fuel components. The different mechanisms by which hydrocarbons in the gasoline escape burning during the normal engine combustion process are described and approximately quantified. The in-cylinder oxidation of these HC during the expansion and exhaust processes, the fraction which exit the cylinder, and the fraction oxidized in the exhaust port and manifold are also estimated.

A method for determining the flame contour based on the flame arrival time at the fiber optic (FO) spark plug and at the head gasket ionization probe (IP) locations has been developed. The experimental data were generated in a single-cylinder Ricardo Hydra spark-ignition engine. The head gasket IP, constructed from a double-sided copper-clad circuit board, detects the flame arrival time at eight equally spaced locations at the top of the cylinder liner. Three other IP's were also installed in the cylinder head to provide additional intermediate data on flame location and arrival time. The FO spark plug consists of a standard spark plug with eight symmetrically spaced optical fibers located in the ground casing of the plug. The cylinder pressure was recorded simultaneously with the eleven IP signals and the eight optical signals using a high-speed PC-based data acquisition system.

This paper uses a model which calculates the flame kernel formation and its early development in spark ignition engines to examine the causes of cycle-to-cycle combustion variations. The model takes into account the primary physical factors influencing flame development. The spark-generated flame kernel size and temperature required to initialize the computation are completely determined by the breakdown energy and the heat conduction from burned region to unburned region. In order to verify the model, the computation results are compared with high-speed Schlieren photography flame development data from an operating spark-ignition engine; they match remarkably well with each other at all test conditions. For the application of this model to the study of cycle-to-cycle variation of the early stage of combustion, additional input is required.

A model which converts flame arrival times at a head gasket ionization probe, used in a spark-ignition engine, into flame contours has been developed. The head gasket was manufactured at MIT using printed circuit board techniques. It has eight electrodes symmetrically spaced around the circumference (top of cylinder liner) and it replaces the conventional head gasket. The model is based on engine flame propagation rate data taken from the literature. Data from optical studies of S.I. engine combustion or studies utilizing optical fiber or ionization probe diagnostics were analyzed in terms of the apparent flame speed and the entrainment speed (flame speed relative to the fluid ahead of the flame). This gives a scaling relationship between the flame speed and the mass fraction burned which is generic and independent of the chamber shape.

A model has been developed which predicts engine-out hydrocarbon (HC) emissions for spark-ignition engines. The model consists of a set of scaling laws that describe the individual processes that contribute to HC emissions. The model inputs are the critical engine design and operating variables. This set of individual process scaling relations was then calibrated using production spark-ignition engine data at a fixed light-load operating point. The data base consisted of engine-out HC emissions from two-valve and four-valve engine designs with variations in spark timing, valve timing, coolant temperature, crevice volume, and EGR, for five different engines. The model was calibrated separately for the three different engines to accommodate differences in engine design details and to determine the relative magnitudes of each of the major sources. A good fit to this database was obtained.

This paper describes the use of a modified quasi-dimensional spark-ignition engine simulation code to predict the extent of cycle-to-cycle variations in combustion. The modifications primarily relate to the combustion model and include the following: 1. A flame kernel model was developed and implemented to avoid choosing the initial flame size and temperature arbitrarily. 2. Instead of the usual assumption of the flame being spherical, ellipsoidal flame shapes are permitted in the model when the gas velocity in the vicinity of the spark plug during kernel development is high. Changes in flame shape influence the flame front area and the interaction of the enflamed volume with the combustion chamber walls. 3. The flame center shifts due to convection by the gas flow in the cylinder. This influences the flame front area through the interaction between the enflamed volume and the combustion chamber walls. 4. Turbulence intensity is not uniform in cylinder, and varies cycle-to-cycle.

The occurrence of liquid fuel in the cylinder of automotive internal combustion engines is believed to be an important source of exhaust hydrocarbon (HC) emissions, especially during the warm-up process following an engine start up. In this study a Phase Doppler Particle Analyzer (PDPA) has been used in a transparent flow visualization combustion engine in order to investigate the phenomena which govern the transport of liquid fuel into the cylinder during a simulated engine start up process. Using indolene fuel, the engine was started up from room temperature and run for 90 sec on each start up simulation. The size and velocity of the liquid fuel droplets entering the cylinder were measured as a function of time and crank angle position during these start up processes. The square-piston transparent engine used gave full optical access to the cylinder head region, so that these droplet characteristics could be measured in the immediate vicinity of the intake valve.

As part of ongoing research on hydrogen-enhanced lean burn SI engines, this paper details an experimental combustion system optimization program. Experiments focused on three key areas: the ignition system, in-cylinder charge motion produced by changes in the inlet ports, and uniformity of fuel-air mixture preparation. Hydrogen enhancement is obtained with a H2, CO, N2 mixture produced by a fuel reformer such as the plasmatron. The ignition system tests compared a standard inductive coil scheme against high-energy discharge systems. Charge motion experiments focused on the impact of different flow and turbulence patterns generated within the cylinder by restrictor plates at the intake port entrance, as well as novel inlet flow modification cones. The in-cylinder fluid motion generated by each configuration was characterized using swirl and tumble flow benches. Mixture preparation tests compared a standard single-hole pintle port fuel injector against a fine atomizing 12-hole injector.