Search Results

An experimental investigation of the effects of ceramic coatings on diesel engine performance and exhaust emissions was conducted. Tests were carried out over a range of engine speeds at full load for a standard metal piston and two pistons insulated with 0.5 mm and 1.0 mm thick ceramic coatings. The thinner (0.5 mm) ceramic coating resulted in improved performance over the baseline engine, with the gains being especially pronounced with decreasing engine speed. At 1000 rpm, the 0.5 mm ceramic coated piston produced 10% higher thermal efficiency than the metal piston. In contrast, the relatively thicker coating (1 mm), resulted in as much as 6% lower thermal efficiency compared to baseline. On the other hand, the insulated engines consistently presented an attractive picture in terms of their emissions characteristics. Due to the more complete combustion in the insulated configurations, exhaust CO levels were between 30% and 60% lower than baseline levels.

A detailed chemical kinetic mechanism, consisting of 22 species and 104 elementary reactions, has been used in conjunction with the multi-dimensional reactive flow code KIVA-3 to study autoignition of natural gas injected under compression ignition conditions. Calculations for three different blends of natural gas are performed on a three-dimensional computational grid by modeling both the injection and ignition processes. Ignition delay predictions at pressures and temperatures typical of top-dead-center conditions in compression ignition engines compare well with the measurements of Naber et al. [1] in a combustion bomb. Two different criteria, based on pressure rise and mass of fuel burned, are used to detect the onset of ignition. Parametric studies are conducted to show the effect of additives like ethane and hydrogen peroxide in increasing the fuel consumption rate.

A prototype chromel-alumel overlapping thin-film thermocouple (TFTC) has been developed for transient heat transfer measurements in ceramic-coated combustion chambers. The TFTC has been evaluated using various metallurgical techniques such as scanning electron microscopy, energy dispersive x-ray detection, and Auger electron spectroscopy. The sensor was calibrated against a standard thermocouple in ice, boiling water, and a furnace at 1000°C. The microstructural and chemical analysis of the thin-films showed the alumel film composition was very similar to the bulk material, while the chromel film varied slightly. An initial set of ceramic plug surface temperatures was taken while motoring and firing the engine at 1900 rpm to verify thermocouple operation. The data shows a 613 K mean temperature and a 55 K swing for the ceramic surface compared with a 493 K mean temperature and a 20 K swing for the metal surface at the same location.

An experimental study of the effects of thin ceramic thermal barrier coatings on the performance of a spark-ignited gasoline engine was conducted. A modified 2.5 liter GM engine with ceramic-coated pistons, liners, head, valves and ports was used. Experimental results obtained from the ceramic engine were compared with baseline metal engine data. It was shown that at low-speed part-load conditions encountered in typical driving cycles the ceramic engine could achieve up to 18% higher brake power and up to 10% lower specific fuel consumption. At wide open throttle conditions, the two engines exhibited similar characteristics, except at high speeds where the metal engine showed better performance at the expense of inferior fuel economy. The ceramic coating did not produce any observable knock in the engine and showed no significant wear at the conclusion of the testing phase.

The thermal conditions of an engine structure, in particular the wall temperatures, have been shown to have a great effect on the HCCI engine combustion timing and burn rates through wall heat transfer, especially during transient operations. This study addresses the effects of thermal inertia on combustion in an HCCI engine. In this study, the control of combustion timing in an HCCI engine is achieved by modulating the residual gas fraction (RGF) while considering the wall temperatures. A multi-cylinder engine simulation with detailed geometry is carried out using a 1-D system model (GT-Power®) that is linked with Simulink®. The model includes a finite element wall temperature solver and is enhanced with original HCCI combustion and heat transfer models. Initially, the required residual gas fraction for optimal BSFC is determined for steady-state operation. The model is then used to derive a map of the sensitivity of optimal residual gas fraction to wall temperature excursions.

This paper analyzes and compares reactor and engine behavior of a diesel oxidation catalyst (DOC) in the presence of conventional diesel exhaust and low temperature premixed compression ignition (PCI) diesel exhaust. Surrogate exhaust mixtures of n-undecane (C11H24), ethene (C2H4), CO, O2, H2O, NO and N2 are defined for conventional and PCI combustion and used in the gas flow reactor tests. Both engine and reactor tests use a DOC containing platinum, palladium and a hydrocarbon storage component (zeolite). On both the engine and reactor, the composition of PCI exhaust increases light-off temperature relative to conventional combustion. However, while nominal conditions are similar, the catalyst behaves differently on the two experimental setups. The engine DOC shows higher initial apparent HC conversion efficiencies because the engine exhaust contains a higher fraction of trappable (i.e., high boiling point) HC.

Characteristics of soot oxidation were investigated with a carbon black (Printex-U). A flow reactor system which can simulate the condition of diesel particulate filter and diesel exhaust gas (1 bar, O2 0 ∼ 10%, NO2 200 ∼ 900ppm) was designed and used with the temperature programmed oxidation (TPO) and constant temperature oxidation (CTO) techniques. The temperature increase rate was 5°C/min for TPO experiments. From the experiments, the apparent activation energy for carbon oxidation with nitrogen dioxide was determined as 60 ± 3 kJ/mol with the first order of carbon in the range of 10∼90% oxidation and the temperature range of 250∼500°C. This value was exceedingly lower than the activation energy of oxygen oxidation which was 177 ± 1 kJ/mol. When oxygen exists with nitrogen dioxide, the reaction rate increased with the concentration of oxygen. Its rate of increase was faster for low oxygen concentration and slower for high concentration.

Today's diesel PM reduction systems are mainly based on catalyzed particulate filter(CPF) systems. However, most of their reaction kinetics remain unresolved. Among others, the soot oxidation rate over catalyst is particularly important in the evaluation of the performance of the catalysts and the efficient control of CPF regeneration. This study, therefore, investigated the oxidation rate of carbon black (Printex-U) over various Pt supported catalysts using a flow reactor setup simulating diesel exhaust conditions. Compared to non-catalyzed soot oxidation, the oxidation rate of carbon black over Pt catalysts was to an extent shifted towards low temperatures. This activity enhancement of soot oxidation over a catalyst can be attributed principally to NO to NO2 conversion because NO2 oxidizes soot with much lower activation energy (Ea=60kJ/mol) than O2 (Ea=177kJ/mol).

The oxidation of soot (carbon black) which is assisted by Pt/CeO2 catalyst is studied using a flow reactor system simulating the condition of diesel exhaust. In this study, the temperature programmed oxidation (TPO) scheme is mainly used for different NO and O2 concentrations and soot oxidation rate is evaluated by monitoring both CO and CO2 concentrations. Pt/CeO2 catalyst lowers the temperature of the peak CO/CO2 concentrations significantly when there is either NO or O2. Oxidation starts at 200°C and the peak CO2 concentration is observed at 360°C, which depends on the amount of catalyst and NO concentration. The effect of catalyst on NO2 recycling is also investigated. For this purpose, two different types of sample have been prepared. For the mixed case, 10mg of carbon black is mixed with 50mg of Pt/CeO2 catalyst under conditions of loose contact. For the unmixed case, the catalyst layer is placed on top of soot layer without mixing.

Diesel particulate filter (DPF) systems are being used to reduce the particulate matter emissions of diesel vehicles. The DPF should be regenerated after certain driving hours or distance to eliminate soot in the filter. The most widely used method is active regeneration with oxygen at 550~650°C. Fuel penalty occurs when the exhaust gas temperature is increased. The low temperature oxidation technique is needed to reduce fuel consumption. In this study, we found that hydrogen could be used to decrease the PM oxidation temperature significantly on a catalyzed DPF (CDPF). The oxidation characteristics of PM with hydrogen supplied to CDPF were studied using a partial flow system. The partial flow system was used to control temperature and a flow rate independently. The CDPF was coated with Pt/Al₂O₃ 25g/ft₃, and a multi-channel CDPF (MC CDPF) with a square cross section of 1.65 cm width and length of 10 cm was used.

This paper reports the development of a model of diesel combustion and NO emissions, based on a modified eddy dissipation concept (EDC), and its implementation into the KIVA-3V multidimensional simulation. The EDC model allows for more realistic representation of the thin sub-grid scale reaction zone as well as the small-scale molecular mixing processes. Realistic chemical kinetic mechanisms for n-heptane combustion and NOx formation processes are fully incorporated. A model based on the normalized fuel mass fraction is implemented to transition between ignition and combustion. The modeling approach has been validated by comparison with experimental data for a range of operating conditions. Predicted cylinder pressure and heat release rates agree well with measurements. The predictions for NO concentration show a consistent trend with experiments. Overall, the results demonstrate the improved capability of the model for predictions of the combustion process.

Adjusting the Residual Gas Fraction (RGF) by means of Variable Valve Actuation (VVA) is a strong candidate for controlling the ignition timing in Homogeneous Charge Compression Ignition (HCCI) engines. However, at high levels of residual gas fraction, insufficient mixing can lead to the presence of considerable temperature and composition variations. This paper extends previous modeling efforts to include the effect of RGF distribution on the onset of ignition and the rate of combustion using a multi-dimensional fluid mechanics code (KIVA-3V) sequentially with a multi-zone code with detailed chemical kinetics. KIVA-3V is used to simulate the gas exchange processes, while the multi-zone code computes the combustion event. It is shown that under certain conditions the effect of composition stratification is significant and cannot be captured by a single-zone model or a multi-zone model using only temperature zones.

NO2 is an effective soot oxidizer operating at lower temperatures than O2. The effect of pure NO2 on soot oxidation was evaluated and compared with the gas treated by plasma, which initially consisted of NO, O2, and hydrocarbons. The cutout of a commercial DPF was used and the pressure difference across the DPF was monitored for an hour. The concentration of NO/NO2, CO, CO2 at the outlet of the DPF was measured as a function of time. CO and CO2 concentration was measured periodically by gas chromatography. The experiment was performed at 230, 250, 300, 350°C. When NO2 only was used as an oxidizing agent, there was a close relationship between the decrease of the pressure difference across the DPF, the CO and CO2 concentration at the outlet of the DPF, and the back conversion of NO2 to NO.

Plasma-catalyst (Ag, Au/Al2O3) systems were applied to NOx reduction in a model lean-burn engine exhaust gas. Also, DeNOx test of real diesel exhaust gas was performed by plasma-Ag/Al2O3 system. In the case of model exhaust gas, the catalytic activity for NOx reduction was enhanced by the assistance of plasma in the wide temperature range. The NOx conversion efficiency of plasma-Ag/Al2O3 was 40∼90% under the condition of C3 H6 3200ppm (C1/NOx = 5.96) and 10% O2 over the temperature range of 250∼400°C. The plasma-Au/Al2 O3 system showed remarkable low temperature NOx reduction activity at 100∼250°C. The real engine full flow test was performed for 70% of the full load and at engine speed of 1500rpm. NOx removal of 46% from the diesel exhaust gas was achieved by the plasma-Ag/Al2O3 catalyst system at 364°C(C1/NOx = 6). In the case of higher C1/NOx = 10, the NOx conversion increased up to 73% at 381°C. Also, DeNOx engine tests were performed for full load of 1500, 2000 and 2500rpm.

Homogeneous charge compression ignition (HCCI) has received much attention in recent years due to its ability to reduce both fuel consumption and NO emissions compared to normal spark-ignited (SI) combustion. However, due to the limited operating range of HCCI, production feasible engines will need to employ a combination of combustion strategies, such as stoichiometric SI combustion at high loads and leaner burn spark-assisted compression ignition (SACI) and HCCI at intermediate and low loads. The goal of this study was to extend the high load limit of HCCI into the SACI region while maintaining a stoichiometric equivalence ratio. Experiments were conducted on a single-cylinder research engine with fully flexible valve actuation. In-cylinder pressure rise rates and combustion stability were controlled using cooled external EGR, spark assist, and negative valve overlap. Several engine loads within the SACI regime were investigated.

The high concentration of particulate matter (PM) in diesel exhaust gas causes significant soot deposition on the wall of EGR cooler, and reduces the heat transfer performance of the EGR cooler and the reduction rate of NOx. The deposition of PM tends to be occurred more severely with "heavy wet PM," which is more frequently at the LTC (low temperature combustion) engine. The objective of this work is to evaluate the effects of soluble organic fraction (SOF) on deposit characteristics of the EGR cooler. To measure reliable mean particle concentration values and surrogate SOFs, the soot generator with SOF vaporizer was used. As for two surrogate SOFs, n-dodecane and diesel lube oil, deposit mass increased when they were injected. Especially from the experiment results, it was found that the lube oil effect was more significant than the n-dodecane effect and lube oil also had a stronger effect on reduction of thermal conductivity by filling pores in deposits.

A program to explore the effects of natural and additive-derived cetane on various aspects of diesel performance and combustion has been carried out. Procedures have been developed to measure diesel engine fuel consumption and power to a high degree of precision. These methods have been used to measure fuel consumption and power in three heavy-duty direct-injection diesel engines. The fuel matrix consisted of three commercial fuels of cetane number (CN) of 40-42, the same fuels raised to CN 48-50 with a cetane improver additive, and three commercial fuels of base CN 47-50. The engines came from three different U.S. manufacturers and were of three different model years and emissions configurations. Both fuel economy and power were found to be significantly higher for the cetane-improved fuels than for the naturally high cetane fuels. These performance advantages derive mainly from the higher volumetric heat content inherent to the cetane-improved fuels.

A high pressure and high temperature evaporation model was implemented in the KIVA-3 multidimensional engine simulation. The most significant features of the new evaporation model are: the effects of Stefan flow on transfer rates are included; internal circulation is accounted using the effective conductivity model of Abramzon and Sirignano [1]; equilibrium composition is calculated at high pressures using a real gas equation of state; and properties are evaluated as functions of temperature, pressure and composition. The evaporation of a continuous spray of n-dodecane injected in a chamber pressurized with nitrogen gas was simulated using the two models. Predictions of the evaporation rate, the spray penetration and fuel vapor distribution by the two models were significantly different. The differences persisted over a range of ambient pressures and temperatures, injection velocities, initial droplet sizes and fuel volatilities.

A comprehensive quasi-dimensional computer simulation of the spark-ignition (SI) engine was used to explore part-load, fuel economy benefits of the Variable Stroke Engine (VSE) compared to the conventional throttled engine. First it was shown that varying stroke can replace conventional throttling to control engine load, without changing the engine characteristics. Subsequently, the effects of varying stroke on turbulence, burn rate, heat transfer, and pumping and friction losses were revealed. Finally these relationships were used to explain the behavior of the VSE as stroke is reduced. Under part load operation, it was shown that the VSE concept can improve brake specific fuel consumption by 18% to 21% for speeds ranging from 1500 to 3000 rpm. Further, at part load, NOx was reduced by up to 33%. Overall, this study provides insight into changes in processes within and outside the combustion chamber that cause the benefits and limitations of the VSE concept.

Variable Compression Ratio (VCR) technology has long been recognized as a method of improving Spark Ignition (SI) engine fuel economy. The Pressure Reactive Piston (PRP) assembly features a two-piece piston, with a piston crown and separate piston skirt which enclose a spring set between them. The unique feature is that the upper piston reacts to the cylinder pressure, accommodating rapid engine load changes passively. This mechanism effectively limits the peak pressures at high loads without an additional control device, while allowing the engine to operate at high compression ratio during low load conditions. Dynamometer engine testing showed that Brake Specific Fuel Consumption (BSFC) improvement of the PRP over the conventional piston ranged from 8 to 18 % up to 70% load. Knock free full load operation was also achieved. The PRP equipped engine combustion is characterized by reverse motion of the piston crown near top dead center and higher thermal efficiency.