Search Results

Induction machines (IM) are considered work horse for industrial applications due to their rugged, reliable and inexpensive nature; however, their low power density restricts their use in volume and weight limited environments such as an aerospace, traction and propulsion applications. Given recent advancements in additive manufacturing technologies, this paper presents opportunity to improve power density of induction machines by taking advantage of higher slot fill factor (SFF) (defined as ratio of bare copper area to slot area) is explored. Increase in SFF is achieved by deposition of copper in much more compact way than conventional manufacturing methods of winding in electrical machines. Thus a design tradeoff study for an induction motor with improved SFF is essential to identify and highlight the potentials of IM for high power density applications and is elaborated in this paper.

A laboratory study was performed to optimize a zoned configuration of an iron (Fe) SCR catalyst and a copper (Cu) SCR catalyst in order to provide high NOx conversion at lean A/F ratios over a broad range of temperature for diesel and lean-burn gasoline applications. With an optimized space velocity of 8,300 hr-1, a 67% (by volume) Fe section followed by a 33% Cu section provided at least 80% NOx conversion from approximately 230°C to 640°C when evaluated with 500 ppm NO and NH3. To improve the lean lightoff performance of the SCR catalyst system during a cold start, a Cu SCR catalyst that was 1/4 as long as the rear Cu SCR catalyst was placed in front of the Fe SCR catalyst. When evaluated with an excess of NH3 (NH3/NO ratio of 2.2), the Cu+Fe+Cu SCR system had significantly improved lightoff performance relative to the Fe+Cu SCR system, although the front Cu SCR catalyst did decrease the NOx conversion at temperatures above 475°C by oxidizing some of the NH3 to N2 or NO.

A laboratory study was performed to assess the effects of SO2 poisoning on the NOx conversion of iron (Fe) and copper (Cu) SCR catalysts. Thermally aged samples of the catalysts were poisoned with SO2 under lean conditions. At various times during the poisonings, the samples were evaluated for NOx conversion with NO and NH3 using lean temperature ramps. The low temperature NOx conversions of both catalysts decreased by 10 to 20% after 1 to 4 hours of poisoning but were stable with continued exposure to the SO2. The poisoned Cu SCR catalyst could be desulfated repeatedly with 5 minutes of lean operation at 600°C. Initially, the poisoned Fe SCR catalyst required 5 minutes of lean operation at 750°C to recover its maximum NOx conversion.

The main classification of Electric Parking Brakes (EPB) can be made into cable puller and caliper integrated types. In this paper, the main design considerations that need to be made for each type of system will be examined. In terms of mechanical design, actuator design factors including target capacity, system size, and vehicle mounting will be briefly discussed. In terms of software, a unified software structure that can incorporate both types of EPBs will be introduced. This unified approach, made up of fixed and variable modules, allows for more efficient software development for both types of EPB systems. The fixed modules are related to the identical target functions regardless of EPB type, while the variable modules are made up of the different considerations that need to be made depending on the EPB type in order to meet such targets. Finally, some test results of target functions for both types of EPB systems will be given.

This paper summarizes results from the author's work on friction in dry sliding contacts in the presence of vibration. A number of idealized models of smooth and rough contacts are examined. It is shown that vibration can cause up to a 10% reduction in average friction even with continuous contact. A larger reduction in friction occurs when there is intermittent contact loss. This is found to be true for both elastic and plastic contacts, and for adhesive and plowing mechanisms of friction. The results of this work are compared and validated with measurements from experiments. The results presented are fundamental, but applicable to machine components with contacts including brake systems.

The RFID on Parts Project Team has recently completed and approved Spec 2000 Chapter 9, “RFID on Parts”. Once approved by the ATA e-Business Steering Group, this standard will allow for archiving and sharing part history information directly on RFID tags using the User Memory Bank. Using a structure similar to a File Storage System, this standard organizes tag data in a structured and indexed system so that information can be shared among all members of the supply chain. Now that high memory, passive tags are becoming available, when used in conjunction with the “RFID on Parts” standard, they make it possible to tag parts not just with an identification number, but with birth records, a full history of maintenance activities and user archives. Since end users and maintenance organizations will no longer need to rely solely on information retrieved from a centralized database, new processes and efficiencies can be realized.

This paper aims to indicate the advantages and any drawbacks of high frequency alternating current (HFAC) power for vehicle auxiliary electrical systems. Generally, benefits of HFAC include efficient power distribution and transformation, space and weight saving and load galvanic isolation. In addition, HFAC bus topologies are distributed to the point of use, lending the system to easy fault detection. The paper is structured as follows: first, the main findings of the most relevant automotive HFAC studies are outlined. Next, an HFAC architecture is proposed which is compared to the existing 14V and proposed 42V centralised DC networks in terms of power distribution efficiency and wiring harness weight saving. For this analysis, the case study of a medium-sized passenger vehicle is considered, and a group of intermittent and continuous auxiliary loads with a cumulative power of 2.8kW.

In the development of a more accurate laboratory scale method, the ability to replicate the thermal oxidative degradation mechanisms seen in gas turbine lubricants, is an essential requirement. This work describes an investigation into the influence of key reaction parameters and the equipment set up upon extent and mechanism of oil degradation. The air flow rate through the equipment was found to be critical to both degradation rate and extent of volatilization loss from the system. As these volatile species can participate in further reactions, it is important that the extent to which they are allowed to leave the test system is matched, where possible, to the conditions in the gas turbine. The presence of metal specimens was shown to have a small influence on the rate of degradation of the lubricant. Loss of metal from the copper and silver specimens due to the mild corrosive effect of the lubricant was seen.

In the sensitive automotive applications like the safety restraint systems (SRS), twisted lines can be used to link the components of the system because of their property of reduction of the electromagnetic interference (EMI) coupling. Compared to the parallel lines, the twisted lines present the drawback to consume more copper in their manufacturing due to the greater length of their conductors. A parametric study based on the numerical modeling and the measurement of twisted lines is conducted in order to analyze the effect of the twisting pitch and of the untwisted part of these lines on the level of EMI coupling. This study will enable to optimize these two parameters in order to reduce the level of EMI coupling as well as the length of the conductors of the lines.

The presentation describes a technical solution for 100 Mbit/s Ethernet Data transmission cabling. This solution considers the specific requirements of automotive wiring harness and manufacturing. It bases on standard automotive connectors and headers. Currently the development of automotive electronic architecture considers central ECU or data backbone structure for the upcoming EE architecture (e. g. single ECU for network; SEN). For these structures solid and cost effective data backbone solutions are essential. Ethernet, a wide distributed and well-known bus system for office and industry data distribution provide a wide range of software tools and many physical layer solutions. Several cabling systems are available. Based on this we propose a solution for automotive application.

In some automotive electrical systems, it is advantageous to use power supplies and loads at two or more voltages. Often it is desirable to retain the single wire power architecture, with the car body providing the return circuit. A major difficulty in achieving this end is the matter of dealing with the possibility of a short circuit between feed wires at different voltages. It can be shown that source-side fuses cannot be relied upon to return the system to a safe state in all cases. Substantial effort was applied to this problem in the early years of the 21st century, but the results were less than completely satisfactory. Using entirely separate cable harnesses for each voltage, with physically separated routing, minimizes the risk of such a short occurring in the harness.

This paper focuses on the numerical simulations of flow around a realistic generic car model called the DrivAer body. This new open-source model is based on the geometries of two medium sized cars, the Audi A4 and the BMW 3 series, and possesses more representative car features as the well-known generic Ahmed body. In this paper, only the fastback geometry is investigated. The flow solver used is ISIS-CFD developed by CNRS and Ecole Centrale de Nantes. This solver is based on a finite-volume method, and two turbulence modelizations are used: the Explicit Algebraic Reynolds Stress Model (EARSM) and a Detached Eddy Simulation (DES). Two meshes are used. For one, the walls are described with a wall function and the mesh contains 19 million cells. This mesh is called “Mesh 1”. For the second mesh, a low-Reynolds number turbulence model for the walls is used. In this case, the mesh contains 39 million cells, and is called “Mesh 2”.

Non-road Tier 4 Final emissions standards offer opportunities for engines to be certified with DOC + SCR aftertreatment systems (ATS), where particulate matter (PM) emissions will be controlled by engine measures. These non-filter systems will not experience high thermal conditions common for filter regeneration and, therefore, will not have the secondary benefit of thermal events removing sulfur from the DOC and SCR aftertreatment. An experimental program was conducted on DOC + SCR systems in which the DOC was selected for the anticipated NO2 and sulfur management requirements of a fixed volume of 3 SCR types (vanadia, copper and iron). Each system was optimized to NOx conversion levels of 90%+ on NRTC cycles then exposed to accelerated sulfur poisoning and various cycles of increasing temperature after each poisoning to observe the performance recovery of the system. Specific sulfur management strategies are defined, depending on technology.

Conventional charging systems for electric and plug-in hybrid vehicles currently use cables to connect to the grid. This methodology creates several disadvantages, including tampering, risk, depreciation and non-value added user efforts. Loose or faulty cables may also create a safety issue. Wireless charging for electric vehicles delivers both a simple, reliable and safe charging process. The system enhances consumer adoption and promotes the integration of electric vehicles into the automotive market. Increased access to the grid enables a higher level of flexibility for storage management, increasing battery longevity. The power class of 3.7kW or less is an optimal choice for global standardization and implementation, due to the readily available power installations for potential customers throughout the world. One of the key features for wireless battery chargers are the inexpensive system costs, reduced content and light weight, easing vehicle integration.

Failure mode and fatigue behavior of dissimilar laser welds in lap-shear specimens of aluminum and copper sheets are investigated. Quasi-static tests and fatigue tests of laser-welded lap-shear specimens under different load ranges with the load ratio of 0.1 were conducted. Optical micrographs of the welds after the tests were examined to understand the failure modes of the specimens. For the specimens tested under quasi-static loading conditions, the micrograph indicates that the specimen failed through the fusion zone of the aluminum sheet. For the specimens tested under cyclic loading conditions, two types of failure modes were observed under different load ranges. One failure mode has a kinked crack initiating from the interfacial surface between the aluminum and copper sheets and growing into the aluminum fusion zone at an angle close to 90°.

The demand for light weight vehicles continues to stimulate extensive research into the development of light weight casting alloys and optimization of their manufacturing processes. Of primary relevance are Aluminum (Al) and Magnesium (Mg) based alloys, which have successfully replaced selected iron based castings in automobiles. However, optimization of as-cast microstructure, processing and performance remains a challenge for some Al-based alloys. In this context, placement of chills in castings has been frequently used to locally manipulate the solidification conditions and microstructure of a casting. In this work, the effect of using an active copper chill on the residual strain profile of a sand-cast B319 aluminum alloy was investigated. Wedge-shaped castings were produced with three different cooling conditions: copper plate chill, copper pipe with cooling water and no chill (baseline).

The 9-meter wind tunnel of the National Research Council (NRC) of Canada is equipped with a boundary layer suction system, center belt and wheel rollers to simulate ground motion relative to test articles. Although these systems were originally commissioned for testing of full-scale automotive models, they are appropriately sized for ground simulation with half-scale tractor-trailer combinations. The size of the tunnel presents an opportunity to test half-scale commercial vehicles at full-scale Reynolds numbers with a model that occupies 3% of the test section cross-sectional area. This study looks at the effects of ground simulation on the force and pressure data of a half-scale model with rotating tractor wheels. A series of model changes, typical of a drag reduction program, were undertaken and each configuration was tested with both a fixed floor and with full-ground simulation to evaluate the effects of this technology on the total and incremental drag coefficients.

Stricter emission limitations for NOx and particulates in mobile diesel applications will require the combinations of active aftertreatment methods like Diesel Particulate Filters (DPF), Selective Catalytic Reduction (SCR) with urea and Lean NOx Trap (LNT) in the 2010's. A new concept is the combination of LNT+SCR, which enables on-board synthesis of ammonia (LNT), which is then removed on the SCR catalyst. The main application for this kind system will be light-duty vehicles, where LNTs are already used and the low temperature deNOx is a main target. That combinatory system was investigated by developing and selecting PtRh/LNT and SCR catalysts for that particulate application, where the maximum temperature may reach 800°C and SCR should proceed without NO2 assistance. Pt-rich, PtRh/LNT with reasonable high loadings above 80g/cft resulted in a high NOx efficiency in the experimental laboratory conditions which created also on LNTs a higher NH3 concentration for the SCR unit.

The recent advance in the development of various hybrid vehicle technologies comes along with the need of establishing optimal energy management strategies, in order to minimize both fuel economy and pollutant emissions, while taking into account an increasing number of state and control variables, depending on the adopted hybrid architecture. One of the objectives of this research was to establish benchmarking performance, in terms of fuel economy, for real time on-board management strategies, such as ECMS (Equivalent Consumption Minimization Strategy), whose structure has been implemented in a SIMULINK model for different hybrid vehicle concepts.

Ultrasonic fatigue tests (testing frequency around 20 kHz) have been conducted on four different cast aluminum alloys each with a distinct composition, heat treatment, and microstructure. Tests were performed in dry air, laboratory air and submerged in water. For some alloys, the ultrasonic fatigue lives were dramatically affected by the environment humidity. The effects of different factors like material composition, yield strength, secondary dendrite arm spacing and porosity were investigated; it was concluded that the material strength may be the key factor influencing the environmental humidity effect in ultrasonic fatigue testing. Further investigation on the effect of chemical composition, especially copper content, is needed.