Search Results

Passengers and flight attendants often notice a haze of smoke under the overhead stowage bins in aircraft cabins when cigarette smoking is allowed. As normally operated, the ventilation system in Boeing 737/757 aircraft does not rapidly remove this smoke haze. Air ionization systems from three vendors were tested in a 10 foot long Boeing 737/757 cabin test section with a cruise condition ventilation rate and two cigarette smoking rates to assess their effectiveness in removing smoke haze from the local breathing areas of passengers and flight attendants. Smoke particulate densities were monitored at five breathing areas and at an exit grill in the test section. All of the ionization systems significantly increased the rate of smoke removal after smoking had stopped, increasing the removal rate by about 25%. None of the systems showed a statistically significant reduction of smoke levels at the individual monitoring points while cigarettes were being smoked.

Flight testing of aircraft under natural icing conditions can be extremely tedious, time consuming, costly, and somewhat risky. However, such testing has been required to demonstrate the effectiveness of anti-icing systems and to certify new aircraft models. To reduce the need for extensive flight testing, Boeing has built a new icing tunnel that has the capability for developing ice shapes and evaluating anti-icing features on full scale sections of critical parts of the aircraft. The icing tunnel was made by modifying an existing 5 ft by 8 ft Boeing Wind Tunnel to add icing capabilities. This paper describes the design specifications, the tunnel capabilities, and the major equipment systems and presents the results of the tunnel calibration relative to the specified requirements.

This paper reviews the recent G189A computer program developments in the area of humidity control for the U.S. Lab Module in the Space Station. The humidity control function is provided as an indirect or passive function by the Common Cabin Air Assemblies (CCAA) in pressurized elements or modules in the Space Station. The CCAAs provide active cabin temperature control through implementation of a digital/electromechanical control system (i.e., a proportional/integral (PI) control system). A selected cabin temperature can be achieved by this control system as long as the sensible and latent heat loads are within specified limits. In this paper three pertinent analytical cases directed to determining minimum or maximum dew point temperatures are discussed. In these cases the basic sensible heat loads are set at constant values.

An overview of composite structure required for manned orbiting space stations is presented. Following a brief introduction of typical configurations and major subsystems, the major structural areas requiring composite structure and their particular functions and requirements are discussed. A summary weight breakdown is presented to assess the dependence of launch weight on these areas. To illustrate, the primary wall composite structure is presented in detail. The design interplay of boost, pressure, meteoroid, radiation, and thermal control requirements are presented. Resultant composite structure for each remaining major structural area is presented in summary form with a brief description of typical design compromises required.

Three separate and distinct electrolytic and one galvanic process were identified by visual inspection, metallographic, electron microprobe, and x-ray diffraction analysis in a clocked, flip-flop integrated circuit flat pack and/or the associated printed circuit test jig (two on flat pack and two on circuit board). These four processes were all found to be detectable by the use of noise measurements in microvolts per root cycle at 1000 Hz (cycles per second). The direct current applied for noise measurement to the integrated circuit devices was 100 micro-amperes, as compared to the 6-8 milliamperes required for normal operation. After initial experimentation, the devices were caused to fail in a laboratory ambient environment, followed by an acceleration of the rate of electrolytic reaction through the use of essentially 100 percent relative humidity, versus the upper specification limit of 80 to 98% relative humidity.

This paper discusses some of the problems of developing and maintaining equipment containing integrated circuits. The problems discussed fall into three categories: (1)Processing, (2) Fault Isolation, and (3) Human Error. Quantitative study of these problems shows the highest number were experienced during preliminary-manufacturing and testing (screening and burn-in), with a decrease during final manufacturing checkout (board assembly and final testing) and a minimum during the system operational period. The paper concludes that maintainability is still the necessity it was even with the advent of reliable integrated circuits. This is substantiated by the many failures and defects encountered during manufacturing and development phases. Manufacturing economics force the consideration of maintainability in integrated circuit design.

Encounters of jet aircraft with high altitude turbulence prompted the investigation of various techniques to probe and locate turbulence in areas lacking particles (rain drops, hailstones). A promising technique is to measure the radio refractive eddies and gradients by radar backscatter. Radio refractive index eddies can, in principle, be found where an atmosphere characterized by a nonadiabatic lapse rate of refractive index is stirred up by turbulence. A sequence of VHF backscatter experiments which will hopefully lead up to an airborne CAT detector are presented in this paper.

This paper addresses the question of whether automation is being used in the proper applications in aircraft in order to maximize aircraft capabilities and make the most of human performance capacity. It is believed that the aircraft designers, while employing automation, have given due regard to the pilot's role as operator and manager of the aircraft. There does, however, seem to be valid concern for the human element in certain aspects of the air traffic control system.

The United States Propulsion Module (USPM) is a pressurized element and provides reboost, propulsive attitude control, control moment gyro (CMG) desaturation, and collision avoidance functions for the International Space Station (ISS). The USPM will dock with Node 2 at the pressurized mating adapter-2 (PMA-2). After docking with PMA-2, the USPM will provide mechanical and structural interfaces to the Space Shuttle, along with facilities for crew transfer and receiving resupply oxygen, nitrogen, water, helium, and propellants from the Space Shuttle. It is essential that the USPM maintain a safe and functional life support system during crew member passage and maintenance activities. It is complex and costly to design an operational system to satisfy all ISS requirements. This paper details an innovative USPM environmental control and life support system (ECLSS) design that satisfies all ISS requirements at a reduced cost.