Search Results

In the diesel sector the fatty acid methyl esters (FAME's) - in Europe mostly RME (rapeseed methyl ester) and in US mostly SME (soja oil methyl ester) - are used as a various share, % volume blends with the diesel fuel (B5, B7, B10, B20, Bxx). The present joint project focuses on RME being the most important representative of the biofuels of 1st generation in Europe. The influences of RME blend fuels on emissions and on lube oil deterioration are emphasized. Emissions were investigated on a modern engine with exhaust gas aftertreatment devices like SCR and (DPF+ SCR). Beside the legally limited exhaust emission components some non-legislated like NO₂, N₂O, NH₃ and nanoparticles were measured at stationary and dynamic engine operation.

Analysis of non-legislated engine-emission components, with different exhaust-gas after-treatment techniques, is an important air quality objective. This paper reports the results for various nitrogen oxides, ammonia and differentiated hydrocarbons emitted at part load from a small 4-S SI engine. It was operated with gasoline, with CNG and with two different three-way catalytic converters. CNG produces less HC and less aromatics. But the HC conversion rate is insufficient. This is due to the lower exhaust gas temperatures, at part load with CNG, and due to the higher stability of light HCs. CNG affects the λ-regulation window, of the investigated system, such that the NOx conversion rate is lowered. In the rich domain of the λ-regulation window, the NO & NOx emissions after catalyst were lowest, while the NH₃ formation was most intense, and vice versa.

During the VERT *) testing of different DPF systems it was remarked, that the oxidation catalyst converts sometimes a big part of NO to NO2, producing on the one hand a more toxic composition of the exhaust gases and causing on the other hand measuring artefacts, which tend to underestimate of NO2 and NOx by the cold NOx - measurement. The present work summarizes the experiences in this matter elaborated at the Laboratories for IC-Engines & Exhaust Emissions Control (AFHB) of the University of Applied Sciences Biel-Bienne, Switzerland, during several VERT activities and didactic projects on engine and chassis dynamometers in the years 2000-2006.

Limited and non-regulated emissions of scooters were analysed during several annual research programs of the Swiss Federal Office of Environment (BAFU) *). Small scooters, which are very much used in the congested centers of several cities, are a remarkable source of air pollution. Therefore every effort to reduce the emissions is an important contribution to improve the air quality in urban centers. In the present work detailed investigations of particle emissions of different 2-stroke scooters with direct injection and with carburettor were performed. The nanoparticulate emissions were measured by means of SMPS, (CPC) and NanoMet. Also the particle mass emission (PM) was measured with the same method as for Diesel engines. Extensive analyses of PM-residuum for SOF/INSOF, PAH and toxicity equivalence (TEQ), were carried out in an international project network. Particle mass emission (PM) of 2-S Scooters consists mostly of SOF.

An active oxidation catalyst is an efficient measure to reduce not only gaseous components (CO, HC), but also particle emissions (mostly oil condensates) of a small 2-stroke engine with lost oil lubrication. Since the 2- and 3-wheelers with 2-stroke propulsion are still a very serious source of air pollution worldwide in many urban areas, it is important to have a look on some consequences of an improperly working catalyst. The present paper shows some results of user-oriented aging of catalyst on the vehicle and results of limited emissions and unlimited (nano)particles during the catalysts screening tests. The works are a part of an international scooter network project, which was performed (2004 to 2007) in the Laboratories for IC-Engines & Exhaust Emission Control of the University of Applied Sciences, Biel, Switzerland with main support of the Swiss Federal Office of Environment (BAFU), Swiss Petrol Union (EV) and Swiss Lubes (VSS).

Advances in emission control technologies have demanded development of new ceramic chemistries and improved microstructures in catalytic substrates and especially in diesel particulate filters. High porosity filters are desirable, as they decrease engine backpressure and enable application of advanced catalysts including, but not limited to, multi-functional filters (MFF). A significant recent development has been in the use of ceramic fibers to create cross-linked microstructures in extruded honeycomb ceramics. This development allows high porosities to be attained while maintaining mechanical strength. However, according to the World Health Organization, certain classes of ceramic fibers are considered to have adverse health effects if released in air and inhaled.

The objectives of the present work are to investigate the regulated and unregulated (particle) emissions of a classical and modern 2-stroke and a typical 4-stroke scooter with different ethanol blend fuels. There is also comparison of two different ethanol fuels: pure ethanol (E) *) and hydrous ethanol (EH) which contains 3.9% water and is denatured with 1.5% gasoline. Special attention is paid in this research to the hydrous ethanol, since the production costs of hydrous ethanol are much less than those for (dry) ethanol. The vehicles are with carburettor and without catalyst, which represents the most frequent technology in Eastern Asia and offers the information of engine-out emissions. Exhaust emissions measurements have been performed with fuels containing ethanol (E), or hydrous ethanol (EH) in the portion of 5, 10, 15 and 20% by volume. During the test systematical analysis of particle mass (PM) and nano-particles counts (NP) were carried out.

Different Diesel Particle Filters (DPF)*) were tested on a 2-Stroke Detroit-Diesel bus engine 6V 92 TA. The investigations focused on soot burden and regeneration of the DPF with special filter materials. Also examined was promoting the regeneration by: throttling, additive (FBC), oxidation catalytic converter upstream of DPF and the catalytic coating of the filter material. The metrics were the particulate matter emission, its composition and the nanoparticles. The most important results are: The average SOF content in the engine exhaust particulate matter is 77.6 % and the majority of it is emitted as bigger droplets The wire-mesh filter catalyst (WFC) - a novel emission reduction technology -substantially curtails the SOF and PM. WFC traps and oxidizes the oil droplets and produces a “dry” soot. This can be very advantageous for the DPF downstream of WFC. (WFC can be also very interesting for 2-S gasoline engines).

In order to meet future requirements for emission reduction and fuel economy a variety of concepts are available for gasoline engines. In the recent past new pathways have been found using alternative fuels and fuel combinations to establish cost optimized solutions. The presented concept for a SI-engine consists of combined injection of gasoline and hydrogen. A hydrogen enriched gas mixture is being injected additionally to gasoline into the engine manifold. The gas composition represents the output of an onboard gasoline reformer. The simulations and measurements show substantial benefits to improve the combustion process resulting in reduced cold start and warm up emissions and optimized part load operation. The replacement of gasoline by hydrogen-rich gas during engine start leads to zero hydrocarbons in the exhaust gas.

1 The topic of investigation of this work was the influence of different gas qualities on the engine parameters and particularly on the air excess factor λ. For this research the normalized gases with extreme compositions were used. At stationary operation there are no differences of the leaning capability of the different gases. The gas with the highest content of inert components causes the lowest full load power, the highest fuel consumption and the highest cyclic irregularity. With the same air flow and the same injection duration for different gases result different air excess factors λ according to the density and to the necessary stoichiometric air quantity of each gas. This fact influences the λ at transient operation conditions as: cold starting, gas quality jump, or load increase, if there is no λ-control. With an active λ-control, which is today fast enough, especially with an adaptive system there are no problems with λ- differences.

1 In the present work investigations of a 7.8 liter-TC-IC-IVECO-CNG engine were performed with single point (SPI) *) and with multipoint (MPI) gas injection systems. Three types of MPI injectors available on the market were compared for stationary and transient engine operation. There are several advantages of MPI e.g. better possibility to equalize the air-fuel-ratio of the cylinders, optimization of the gas injection timing and of the gas pressure for different operating conditions. With different injector types there are different optimum injection timings, due to different injection durations, but at the optimum conditions there is little difference in the combustion quality. The injectors with higher flow rate can cause more λ-excursions in the dynamic response and with sudden changes of the gas pressure.

In this study, the combustion of butanol, neat and mixed with gasoline, was investigated on a 0.6 liter two-cylinder spark ignition engine with fully adjustable fuel injection and spark timing, coupled with an eddy current dynamometer. Two isomers of butanol, n-butanol and iso-butanol, were examined. This basic parameter study gives information about potential requirements of engine control systems for butanol FFV. Compared to the traditionally used ethanol, butanol does not exhibit hygroscopic behaviour, is chemically less aggressive and has higher energy density. On other hand, different laminar burning velocity and higher boiling temperature of butanol, compared to gasoline, requires some countermeasures to keep the engine operation reliable and efficient.

During the first decade of diesel particle filter development and deployment in cars, trucks, buses and underground sites, DPF regeneration methods were engineered that were compatible with the then prevalent high sulfur content in the fuel ≻ 2000 ppm. The mainly used methods were burners, electrical heaters, replaceable filters and non-precious metal fuel additives. Low sulfur diesel fuel became only available from 1996 in Sweden, 1998 in Switzerland, and after 2000 everywhere in Europe. Thus, the deployment of precious metal catalytic converters was feasible both as original equipment and retrofitting of in-use engines. The so-called CRT particle filters using PGM-catalysis for providing NO₂ for low temperature regeneration became very successful wherever ULSD was available.

The most efficient way and the best available technology (BAT) to radically reduce the critical diesel emission components particles (PM&NP) and nitric oxides (NOx) are combined exhaust gas aftertreatment systems (DPF+SCR). SCR (selective catalytic reduction) is regarded as the most efficient deNOx-system, diesel particle filters are most efficient for soot abatement. Today, several suppliers offer combined systems for retrofitting of HD vehicles. The presented results are part of the work in the international network project VERT *) dePN (de-activation, de-contamination, disposal of particles and NOx), which has the objectives to establish test procedures and quality standards and to introduce the SCR-, or combined DPF+SCR-systems in the VERT verification procedure.

Exhaust emissions measurements of a small 2-S Scooter Peugeot TSDI*), 50cc with different particle filters have been performed in this present work according to the measuring procedures, which were established in the previous research in the Swiss Scooter Network, [1, 2, 3, 4, 5, 6, 7, 8, 9]. The investigated particle filtration materials were supplied from different manufacturers as samples without specifications and they were applied by the research laboratory in a special muffler able to be taken apart. The investigated scooter represented a modern (2002) 2-stroke technology with direct injection, with oxidation catalyst and with injection of the lube oil to the intake air. Since there is a special concern about the particle emissions of the small engines, the particle mass and nanoparticle measurements were systematically carried out. The nanoparticulate emissions were measured by means of SMPS (CPC) and NanoMet*).

Macroscopic studies and scanning electron microscope (SEM), as well as transmission electron microscope (TEM) research were carried out to investigate the nature and properties of particulate matter (PM) deposited in three diesel particulate filters (DPFs) operating with different fuels: 100% rapeseed methyl ester (RME100), a blend of 20% RME and 80% diesel (RME20), as well as 100% diesel (RME0). The DPFs were catalytically coated with V₂O₅/TiO₂. The PM deposits were either extracted from sectioned DPFs or studied "in situ," as deposited. In the RME100-DPF, the lowest soot and highest ash depositions are found. The higher amount of ash in RME100-DPF, as well as the higher participation of the element Ca in the ash from this filter, indicates that in addition to lubricating oil, the RME fuel contributes also to ash formation. Ash is found accumulating in the plugged inlet channels only in RME100 and as a few tens of μm-thick layer on the channel walls of all three filters.

Further efforts to reduce the air pollution from traffic are undertaken worldwide and the filtration of exhaust gas will also be increasingly applied on gasoline cars (GPF1 … gasoline particle filter). In the present paper, some results of investigations of nanoparticles from four MPI gasoline cars are represented. The measurements were performed at vehicle tailpipe and in CVS-tunnel. Moreover, two variants of GPF were investigated on a high-emitting modern vehicle, including analytics of PAH and attempts of soot loading in road application. The modern MPI vehicles can emit a considerable amount of PN, which in some cases attains the level of Diesel exhaust gas without DPF and can pass over the actual European limit value for GDI (6.0 x 1011 #/km). The GPF-technology offers in this respect further poten-tials to reduce the PN-emissions of traffic.

In order to analyze the processes during the gas exchange in the engine, knowledge of pressure states in both inlet and outlet is required. This pressure measuring is known as “low pressure indication”. In the present work, three examples of controlling the quality of low pressure measurement are presented. An insight in the pressure waves in exhaust pipe, especially in the exhaust blow-off is given. It was shown that: a small inaccuracy of measurement, lower than 10 mbar can be attained, the asymmetric course of the exhaust pulse can clearly be verified, and a protection screen for a sensor exposed to the exhaust blow-off pressure wave can be a tool to optimize between longlife and accuracy. The most important statements are: both presented methods of low pressure indication - the direkt and the indirect yield the results with highest accuracy.

Nanoparticle emissions of two 2-stroke scooters were investigated along the exhaust and the CVS (Constant Volume Sampling) systems. Two configurations were tested: regular full-flow dilution configuration (denoted as “closed”) and also a modified sampling configuration (denoted as “open”). The scooters represent two distinct modern technologies. One scooter had direct injection TSDI*) (Two-Stroke Direct Injection). The other had a carburettor. Depending on the technology, the scooters produce different kind of aerosols (state-of-oxidation and SOF content). Moreover, the scooters were operated with and without oxidation catalyst. The tests were performed at two constant vehicular speeds (20 km/h and 40 km/h). The measuring procedures are those established during the previous research of the Swiss Scooter Network. The nanoparticulate emissions were measured using SMPS (Scanning Mobility Particle Sizer) and DC (Diffusion Charging) sensors.

Limited and nonlimited emissions of scooters were analysed during several annual research programs of the Swiss Agency of Environment Forests and Landscape (SAEFL, BUWAL)*). Small scooters, which are very much used in the congested centers of several cities are a remarkable source of air pollution. Therefore every effort to reduce the emissions is an important contribution to improve the air quality in urban centers. In the present work detailed investigations of particle emissions of different 2-stroke scooters with direct injection and with carburetor were performed. The nanoparticulate emissions with different lube oils and fuels were measured by means of SMPS, (CPC) and NanoMet *). Also the particle mass emission (PM) was measured with the same method as for Diesel engines. Extensive analyses of PM-residuum for PAH & SOF/INSOF, as well as for VOC were carried out in an international project network.