Standard
Fuel Fired Engine Preheaters and Their Application
2002-12-16
CURRENT
J1327_200212
Search Results
Standard
Combination Tail and Floodlamp for Industrial Equipment
2003-05-15
CURRENT
J94_200305
This SAE Standard provides performance and general design requirements and related test procedures for a combination tail and floodlamp for use on industrial wheeled equipment that may be operated on public roads.
Standard
SAE J1939 Network Security
2017-03-06
WIP
J1939-91
This document will provide recommendations to vehicle manufacturers and component suppliers in securing the SAE J1939-13 connector interface from the cybersecurity risks posed by the existence of this connector.
Standard
Air Filter Element Test Method
2022-07-14
CURRENT
J1533_202207
This SAE test method establishes a uniform test procedure for determining the gravimetric (mass based) efficiency and pressure drop performance levels of operator enclosure panel type filters on off-road, self-propelled work machines used in earth moving, and forestry, as defined in SAE J1116 and for agricultural equipment as defined in ANSI/ASAE S390, and equipped with an operator enclosure with a powered fresh air system. ISO/TS 11155-1 may additionally be used, which describes the use of particle sizing devices to measure the fractional (particle size) efficiency of panel type filters for automotive cabin filter applications. Automotive cabin filters are similar to filters described in this procedure, and the ISO/TS 11155-1 test method is therefore directly applicable.
Standard
Air Filter Element Test Method
2019-07-03
HISTORICAL
J1533_201907
This SAE test method establishes a uniform test procedure for determining the gravimetric (mass based) efficiency and pressure drop performance levels of operator enclosure panel type filters on off-road, self-propelled work machines used in earth moving, and forestry, as defined in SAE J1116 and for agricultural equipment as defined in ANSI/ASAE S390, and equipped with an operator enclosure with a powered fresh air system. ISO/TS 11155-1 may additionally be used, which describes the use of particle sizing devices to measure the fractional (particle size) efficiency of panel type filters for automotive cabin filter applications. Automotive cabin filters are similar to filters described in this procedure, and the ISO/TS 11155-1 test method is therefore directly applicable.
Standard
OPERATOR ENCLOSURE AIR FILTER ELEMENT TEST PROCEDURE
1993-06-14
HISTORICAL
J1533_199306
This SAE Recommended Practice establishes a uniform test procedure for determining performance levels of operator enclosure panel type air filters on off-road, self-propelled work machines used in construction, general-purpose industrial, agriculture, and forestry as defined in SAE J1116 and equipped with an operator enclosure with a powered fresh air system.
Standard
Hydraulic System Diagrams and Associated Tables for Marine Vehicles
2012-09-17
WIP
J1780
This document establishes the requirements for technical content and format of hydraulic system diagrams. This document does not establish configuration requirements, material, or performance requirements for any system or component identified herein. The purpose of this document is to specify the minimum technical content of marine and submergence vehicle hydraulic system diagrams and provide a standard format. Diagrams prepared in accordance with this document will be suitable for use in procurement activity, shipboard installation, and technical manuals for use in troubleshooting, operation, and maintenance of the hydraulic system.
Standard
HYDRAULIC SYSTEM DIAGRAMS AND ASSOCIATED TABLES FOR MARINE VEHICLES
1991-04-01
CURRENT
J1780_199104
This document establishes the requirements for technical content and format of hydraulic system diagrams. This document does not establish configuration requirements, material, or performance requirements for any system or component identified herein.
Standard
Heavy Duty Vehicle Lubricating Greases
2005-08-11
CURRENT
J2695_200508
This SAE Recommended Practice was developed by SAE, and the section “Standard Classification and Specification for Service Greases” cooperatively with ASTM, and NLGI. It is intended to assist those concerned with the design of heavy duty vehicle components, and with the selection and marketing of greases for the lubrication of certain of those components on heavy duty vehicles like trucks and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of heavy duty vehicle greases.
Standard
Discriminating Back-Up Alarm System Standard
1999-06-01
CURRENT
J1741_199906
This SAE Standard describes methods for evaluating the performance of the systems detection device, the minimum detection areas behind the machine, the visual and audible information presented to the operator and ground personnel, and the systems fault detection requirements. Also included are operator system function tests and maintenance procedures.
Standard
Clutch Application Powertrain Startability Rating Requirements for Truck and Bus Applications
2004-08-25
HISTORICAL
J2469_200408
Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).
Standard
Clutch Application Powertrain Startability Rating Requirements for Truck and Bus Applications
2017-09-19
CURRENT
J2469_201709
Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).
Standard
Tire Size Differential - Articulated Wheel Loader
2019-11-20
CURRENT
J2204_201911
This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.
Standard
TIRE SIZE DIFFERENTIAL—ARTICULATED WHEEL LOADER
1994-05-01
HISTORICAL
J2204_199405
This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.
Standard
Fasteners - Part Standard - Cap Screws, Hex Bolts, and Hex Nuts (Metric)
2019-05-10
CURRENT
J2295M_201905
This SAE Part Standard covers selected metric screws, hex bolts, and nuts manufactured in accordance with American Society for Testing and Materials (ASTM) and SAE fastener standards. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document.
Standard
Fasteners—Part Standard—Cap Screws, Hex Bolts, and Hex Nuts (Metric)
2006-06-21
HISTORICAL
J2295M_200606
This SAE Part Standard covers selected metric screws, hex bolts, and nuts manufactured in accordance with American Society for Testing and Materials (ASTM) and SAE fastener standards. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document.
Standard
SHIP SYSTEMS AND EQUIPMENT—FASTENERS—SELECTION AND IDENTIFICATION REQUIREMENTS
1996-04-01
HISTORICAL
J2280_199604
This SAE Standard provides a comprehensive list of requirements for the selection, identification, and control of metric and inch sized fasteners for use in shipboard applications for both shipbuilder installed joints and for use in shipboard components. The fastener selection requirements include the following: a Materials b Thread selection c Plating, coatings, and surface treatments d Locking devices and elements e Screw thread fastener inserts f Fastener part or identifying numbers g Identification markings
Standard
Clutch Dimensions for Truck and Bus Applications
2017-08-14
CURRENT
J1806_201708
Although not limited to, these clutches are normally used on trucks considered as Medium-Duty (Class 6 and 7), as well as Heavy-Duty (Class 8).
Standard
Clutch Dimensions for Truck and Bus Applications
1999-11-30
HISTORICAL
J1806_199911
Although not limited to, these clutches are normally used on trucks considered as Medium-Duty (Class 6 and 7), as well as Heavy-Duty (Class 8).
Standard
Clutch Installation and Release Linkage Requirements for Truck and Bus Application
2017-11-03
CURRENT
J2407_201711
Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).
