Search Results

Standard

Hole Placement on Dozer End Bits

1986-05-01

HISTORICAL

J63_198605

It is the purpose of the SAE Recommended Practice to define the minimum requirements for hole placement on Dozer End Bit supports. The recommended practice applies to straight blade, angling blade, U blade, and semi-U blades used on earthmoving tractors per SAE J1057a up to a maximum weight of 100,000 lb (45,000 kg).

Standard

Hole Placement on Dozer End Bits

1998-05-01

CURRENT

J63_199806

The recommended practice applies to straight blade, angling blade, U blade, and semi-U blades used on earthmoving tractors per SAE J1057a up to a maximum weight of 100,000 lb (45,000 kg).

Standard

NOMENCLATURE—ROLLERS AND COMPACTORS

1986-01-01

HISTORICAL

J1017_198601

This SAE Standard provides names of major components peculiar to rollers and compactors. Illustrations of components are not intended to be exactly descriptive of any particular machine. See Figures 1 to 3.)

Standard

Component Nomenclature--Dumpers

2000-06-28

CURRENT

J1016_200006

This SAE Standard provides names of major components peculiar to dumpers as defined in SAE J1057 (See Figure 1). Illustrations of components are not intended to be exactly descriptive of any particular machine. For component nomenclature for dumper trailers, refere to SAE J734.

Standard

CAPACITY RATING—DOZER BLADES

1988-03-01

HISTORICAL

J1265_198803

This standard applies only to straight, angling, semi-U, and U-blades for crawler and wheel tractors. It applies to angling blades only in the straight (not angled) position.

Standard

HOLE SPACING FOR SCRAPER AND DOZER CUTTING EDGES

1989-08-01

HISTORICAL

J737_198908

This standard is intended for cutting edge sections used on: a Tractor-scrapers as described in SAE J1057 and J728. b Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation.

Standard

HOLE SPACING FOR SCRAPER AND DOZER CUTTING EDGES

1983-05-01

HISTORICAL

J737_198305

This standard is intended for cutting edge sections used on: (1) Tractor-scrapers as described in SAE J1057 and J728. (2) Dozers as described in SAE J173. These cutting edges are further defined in SAE J738 for cross section and SAE J740 for hole conformation.

Standard

COMPONENT NOMENCLATURE—SCRAPERS

1990-07-01

HISTORICAL

J728_199007

This SAE Standard provides names of major components peculiar to the scraper portion of tractor-scrapers. Reference SAE J1057. Illustrations of components are not intended to be exactly descriptive of any particular machine.

Standard

Hole Spacing for Scraper and Dozer Cutting Edges

2007-08-30

CURRENT

J737_200708

This standard is intended for cutting edge sections used on: a. Tractor-scrapers as described in SAE J1057 and J728 b. Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation. (Note: Some inch dimentions in this standard are not equivalent to the corresponding millimeter figures because values which are widely used have been adapted. This standard specifies hole placement along with length and width of the cutting edge.

Standard

COMPONENT NOMENCLATURE—GRADERS

1990-07-30

HISTORICAL

J870_199007

This SAE Standard provides names of major components peculiar to graders as defined in SAE J1057 (See Figure 1). Illustrations of components are not intended to be exactly descriptive of any particular machine.

Standard

CAPACITY RATING—ELEVATING SCRAPERS

1993-06-01

HISTORICAL

J957_199306

This SAE Standard specifies a procedure for approximating the volume of a typical material carried in the bowl of an elevating scraper as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and a representative volume on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.

Standard

CAPACITY RATING—DUMPER BODY AND TRAILER BODY

1995-11-01

HISTORICAL

J1363_199511

This SAE Standard applies to dumper bodies as defined in SAE J1016 and dumper trailers as defined in SAE J734. It is similar to ISO 6483.

Standard

CAPACITY RATING—SCRAPER, OPEN BOWL

1993-06-01

HISTORICAL

J741_199306

This SAE Standard specifies a procedure for approximating the volume of typical materials contained in the bowl of Open Bowl scrapers as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and representative volumes on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.

Standard

CAPACITY RATINGS—SCRAPER, DUMPER BODY AND TRAILER BODY

1975-06-01

HISTORICAL

J741B_197506

Standard

Cutting Edge - Cross Sections Loader Straight with Bolt Holes

2011-10-25

CURRENT

J1304_201110

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters. NOTE—For some heavy-duty applications, cross sections with larger blunts, greater bevel angles, and larger bolt holes may be required.

Standard

Cutting Edge—Double Bevel Cross Sections

2008-07-07

HISTORICAL

J738_200807

This standard is for cutting edge sections typically used in earthmoving machinery defined in SAE J1507: a Tractor - Scrapers as defined in SAE J728. b Dozers as described in SAE J729 and J173. c Loaders as described in SAE J731. d Graders as described in SAE J870. Hole spacing is defined for dozers and scrapers in J737 and graders in J739. Hole conformation is defined in J740.

Standard

Cutting Edge - Double Bevel Cross Sections

2014-01-08

HISTORICAL

J738_201401

This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a Scrapers as defined in ISO 7133. b Dozers as described in ISO 6747. c Loaders as described in ISO 7131. d Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.

Standard

Cutting Edge - Double Bevel Cross Sections

2020-01-15

CURRENT

J738_202001

This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a Scrapers as defined in ISO 7133. b Dozers as described in ISO 6747. c Loaders as described in ISO 7131. d Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.

Standard

CUTTING EDGE—DOUBLE BEVEL CROSS SECTIONS

1986-06-01

HISTORICAL

J738_198606

This standard is for cutting edge sections typically used in earthmoving machinery defined in SAE J1507: a Tractor - Scrapers as defined in SAE J728. b Dozers as described in SAE J729 and J173. c Loaders as described in SAE J731. d Graders as described in SAE J870. Hole spacing is defined for dozers and scrapers in J737 and graders in J739. Hole conformation is defined in J740.

Standard

CUTTING EDGE—CURVED GRADER

1991-06-01

HISTORICAL

J739_199106

This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580.