Search Results

Optimization of the engine cold start is critical for gasoline direct injection (GDI) engines to meet increasingly stringent emission regulations, since the emissions during the first 20 seconds of the cold start constitute more than 80% of the hydrocarbon (HC) emissions for the entire EPA FTP75 drive cycle. However, Direct Injection Spark Ignition (DISI) engine cold start optimization is very challenging due to the rapidly changing engine speed, cold thermal environment and low cranking fuel pressure. One approach to reduce HC emissions for DISI engines is to adopt retarded spark so that engines generate high heat fluxes for faster catalyst light-off during the cold idle. This approach typically degrades the engine combustion stability and presents additional challenges to the engine cold start. This paper describes a CFD modeling based approach to address these challenges for the Ford 3.5L V6 EcoBoost engine cold start.

A kinetic carbon monoxide (CO) emission model is developed to simulate engine out CO emissions for conventional diesel combustion. The model also incorporates physics governing CO emissions for low temperature combustion (LTC). The emission model will be used in an integrated system level model to simulate the operation and interaction of conventional and low temperature diesel combustion with aftertreatment devices. The Integrated System Model consists of component models for the diesel engine, engine-out emissions (such as NOx and Particulate Matter), and aftertreatment devices (such as DOC and DPF). The addition of CO emissions model will enhance the capability of the Integrated System Model to predict major emission species, especially for low temperature combustion. In this work a CO emission model is developed based on a two-step global kinetic mechanism [8].

This paper describes a CFD modeling based approach to address design challenges in GDI (gasoline direct injection) engine combustion system development. A Ford in-house developed CFD code MESIM (Multi-dimensional Engine Simulation) was applied to the study. Gasoline fuel is multi-component in nature and behaves very differently from the single component fuel representation under various operating conditions. A multi-component fuel model has been developed and is incorporated in MESIM code. To apply the model in engine simulations, a multi-component fuel recipe that represents the vaporization characteristics of gasoline is also developed using a numerical model that simulates the ASTM D86 fuel distillation experimental procedure. The effect of the multi-component model on the fuel air mixture preparations under different engine conditions is investigated. The modeling approach is applied to guide the GDI engine piston designs.

Two different types of mesh used for diesel combustion with the KIVA-4 code are compared. One is a well established conventional KIVA-3 type polar mesh. The other is a non-polar mesh with uniform size throughout the piston bowl so as to reduce the number of cells and to improve the quality of the cell shapes around the cylinder axis which can contain many fuel droplets that affect prediction accuracy and the computational time. This mesh is specialized for the KIVA-4 code which employs an unstructured mesh. To prevent dramatic changes in spray penetration caused by the difference in cell size between the two types of mesh, a recently developed spray model which reduces mesh dependency of the droplet behavior has been implemented. For the ignition and combustion models, the Shell model and characteristic time combustion (CTC) model are employed.

SAIC Motor has developed an all new 2.0 L 4-cylinder turbocharged gasoline direct injection engine to meet the market demand and increasingly stringent requirement of CAFE and tail-pipe emission regulations. A series of advanced technologies have been employed in this engine to achieve high efficiency, high torque and power output, fast response low-end torque performance, refined NVH performance, all at market leading level, and low engine-out emissions. These main technologies include: side mount gasoline direct injection with 35MPa fuel injection system, integrated exhaust manifold, high tumble combustion system, 2-step intake variable valve lift (DVVL) with Miller Cycle, efficient turbo charging with electric wastegate (EWG), light weight and compact structural designs, NVH measures including balancer system with silence gear, friction reduction measures, optimized thermal management, etc.

The present paper describes a CAE analysis approach to evaluate the transient cylinder head gasket sealing performance of a turbo charged GDI engine in the bench test development. In this approach, both transient gasket sealing force and gasket wear work are calculated to allow design engineers to find out the root cause of cylinder head gasket leakage failures. In this paper, the details of the method development are described. Firstly how to use and get the cylinder head gasket property are described, which is the basic theory and data for the gasket sealing analysis. A transient heat transfer calculation for accurately simulating the engine thermal shock test is established, which is mapped to the transient gasket sealing calculation as pivotal boundary.

In order to predict more accurately the cracking failure of cylinder head during the durability test of turbocharged engine in the development, a comprehensive evaluation method of cylinder head durability is established. In this method, both high cycle and low cycle fatigue performance are calculated to provide failure assessment. The method is then applied to investigate the root cause of cracking of cylinder head and assess design optimizations. Multidisciplinary approach is adopted to optimize high cycle fatigue and low cycle fatigue performance simultaneously to achieve the best comprehensive performance. In this paper, the details of the method development are described. First, the high cycle and low cycle fatigue properties of cylinder head material were measured at different temperature condition, and the fatigue life and high temperature creep properties of materials under thermo-mechanical fatigue cycle were also tested.

A new range-extension hybrid powertrain concept, namely the Tongji Extended-range Hybrid Technology (TJEHT) was developed and demonstrated in this study. This hybrid system is composed of a direct-injection gasoline engine, a traction motor, an Integrated Starter-Generator (ISG) motor, and a transmission. In addition, an electronically controlled clutch between the ISG motor and engine, and an electronically controlled synchronizer between the ISG motor and transmission are also employed in the transmission case. Hence, this system can provide six basic operating modes including the single-motor driving, dual-motor driving, serial driving, parallel driving, engine-only driving and regeneration mode depending on the engagement status of the clutch and synchronizer. Importantly, the unique dual-motor operation mode can improve vehicle acceleration performance and the overall operating efficiency.

Recently, Ford Motor Company announced the introduction of EcoBoost engines in its Ford, Lincoln and Mercury vehicles as an affordable fuel-saving option to millions of its customers. The EcoBoost engine is planned to start production in June of 2009 in the Lincoln MKS. The EcoBoost engine integrates direct fuel injection with turbocharging to significantly improve fuel economy via engine downsizing. An application of this technology bundle into a 3.5L V6 engine delivers up to 12% better drive cycle fuel economy and 15% lower emissions with comparable torque and power as a 5.4L V8 PFI engine. Combustion system performance is key to the success of the EcoBoost engine. A systematic methodology has been employed to develop the EcoBoost engine combustion system.

SAIC Motor Corporation Limited (SAIC Motor) has developed a new 1.5 L 4-cylinder turbocharged gasoline direct injection engine to meet the market demand and increasingly stringent requirement of CAFE and tail-pipe emission regulations. A series of advanced technologies for improving engine fuel economy, engine-out emission, torque and power output specially low end torque performance have been employed, such as: central gasoline direct injection, integrated exhaust manifold, high tumble combustion system, Miller Cycle, cooled external EGR, 35MPa fuel injection system, multi-hole injector with variable hole size design, efficient turbo charging with electric wastegate (EWG), etc. As a result, the engine is able to achieve over 39% brake thermal efficiency (BTE), as well as substantial fuel consumption reduction in vehicle driving cycle. It delivers 275 Nm maximum torque and 127kW rated power, with fast low end torque response.

An integrated system model containing sub-models for diesel engine, emissions, and aftertreatment devices has been developed. The objective is to study engine-device and device-device interactions. The emissions sub-models used are for NOx and PM (particulate matter) prediction. The aftertreatment sub-models used include a diesel oxidation catalyst (DOC) and a diesel particulate filter (DPF). Controllers have also been developed to allow for transient simulations, active DPF regeneration, and prevention/control of runaway DPF regenerations. The integrated system-level model has been used to simulate DPF regeneration via exhaust fuel injection ahead of the DOC. In addition, the controller model can use intake throttling to assist in active DPF regeneration if needed. Regeneration studies have been done for both steady engine load and with load transients. High to low engine load transients are of particular interest because they can lead to runaway DPF regeneration.

Two turbulent combustion modeling approaches, which were large eddy simulations in conjunction with detailed kinetics (LES-CHEMKIN) and Reynolds Averaged Navier Stokes with detailed kinetics (RANS-CHEMKIN), were used to model two partially premixed engine conditions. The results were compared with average pressure and heat release data, as well as images of in-cylinder ignition chemiluminescence and OH radical distributions. Both LES-CHEMKIN and RANS-CHEMKIN match well with experimental average data. However, LES-CHEMKIN has advantages over RANS-CHEMKIN in predicting the details of location of ignition sites, temperature as well as OH radical distributions. Therefore, LES offers more realistic representations of the combustion process. As a further improvement aiming at saving computational cost and accounting for turbulence-chemistry interactions, a flamelet time scale (FTS) combustion model is coupled with CHEMKIN to predict the entire combustion process. In this new approach (i.e.

Numerical models were used to study the effects of dimethyl ether (DME) on the operation of a compression-ignition engine fueled with premixed natural gas. The models used multi-dimensional engine CFD coupled with detailed chemical kinetics. Combustion characteristics of various compositions of the natural gas and DME mixture were simulated. Results showed that combustion phasing, nitrogen oxides emissions, and effects of fuel compositions on engine operating limits were well predicted. Chemical kinetics analysis indicated that ignition was achieved by DME oxidation, which, in turn, induced natural gas combustion. It was found that low temperature heat release became more significant as DME concentration increased. For an appropriate amount of DME in the mixture, the stable engine operating range became narrower as natural gas concentration increased. The model also captured the low temperature combustion features of the present engine with low nitrogen oxides emissions.

Particulate matters, nitrogen oxides, and carbon monoxides emissions from large utility generators using diesel/biodiesel blends were measured. Stack measurements were performed on-site in a number of power plants by following the standard procedure of US EPA. The test engines were chosen to represent typical diesel engines used for electricity generation in the state. Tests were performed using the regular diesel fuel (B0), 10%, 20% and 100% biodiesel blends (B10, B20, B100). Test results showed that particulate matters and carbon monoxides decreased significantly as biodiesel content increases, whereas nitrogen oxides increased. Test results are consistent with other studies using mobile engines in the literature. Note that arbitrary changes in fuel or engine operating conditions are prohibited in power generation industry. Results of this study have been used by the state government to allow the use of biodiesel blends in stationary generators.

The accurate prediction of fuel sprays is critical to engine combustion and emissions simulations. A fine computational mesh is often required to better resolve fuel spray dynamics and vaporization. However, computations with a fine mesh require extensive computer time. This study developed a methodology that uses a locally refined mesh in the spray region. Such adaptive mesh refinement will enable greater resolution of the liquid-gas interaction while incurring only a small increase in the total number of computational cells. The present study uses an h-refinement adaptive method. A face-based approach is used for the inter-level boundary conditions. The prolongation and restriction procedure preserves conservation of properties in performing grid refinement/coarsening. The refinement criterion is based on the mass of spray liquid and fuel vapor in each cell. The efficiency and accuracy of the present adaptive mesh refinement scheme is demonstrated.

A general combustion model, in the context of large eddy simulations, was developed to simulate the full range of combustion in conventional diesel-type and HCCI-type diesels. The combustion model consisted of a Chemkin sub-model and an Extended Flamelet Time Scale (EFTS) sub-model. Specifically, Chemkin was used to simulate auto-ignition process. In the post-ignition phase, the combustion model was switched to EFTS. In the EFTS sub-model, combustion was assumed to be a combination of two elementary combustion modes: homogeneous combustion and flamelet combustion. The combustion index acted as a weighting factor blending the contributions from these two modes. The Chemkin sub-model neglected the subgrid scale turbulence-chemistry interactions whereas the EFTS model took them into account through a presumed PDF approach. The model was used to simulate an early injection mode of a Cummins DI diesel engine and a mode of a Caterpillar DI diesel engine.

System level modeling was used to develop a suitable control strategy for Diesel Homogeneous Charge Compression Ignition (HCCI) transient operation. Intake temperature and pressure, engine speed, engine load, cylinder wall temperature, exhaust gas recirculation, etc. all significantly affect combustion phasing generating a scenario where simple ECU mapping techniques prove inadequate. Two-stage fuels such as diesel fuel pose additional challenges for accurate combustion control. Low-temperature cool-flame chemical heat release can significantly alter the thermodynamic state of the trapped gaseous mixture and hence combustion phasing. Operator and environmentally induced transients can rapidly alter combustion phasing parameters suggesting a need for model-based control. A model-based control strategy featuring the identified essential physics has been developed to control diesel HCCI combustion phasing through transient operation.

An integrated system model containing sub-models for a multi-cylinder diesel engine, NOx and soot(PM) emissions, diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) has been developed to simulate the engine and aftertreatment systems at transient engine operating conditions. The objective of this work is two-fold; ensure correct implementation of the integrated system level model and apply the integrated model to understand the fuel economy trade-off for various DPF regeneration strategies. The current study focuses on a 1.9L turbocharged diesel engine and its exhaust system. The engine model was built in GT-Power and validated against experimental data at full-load conditions. The DPF model is calibrated for the current engine application by matching the clean DPF pressure drop for different mass flow rates. Load, boost pressure, speed and EGR controllers are tuned and linked with the current engine model.

The simultaneous reduction of particulate matter (PM) and nitrous oxides (NOx) emissions form diesel exhaust is key to current research activities. Although various technologies have been introduced to reduce emissions from diesel engines, the in-cylinder reduction of PM and NOx due to improved combustion mechanisms will continue to be an important field in research and development of modern diesel engines. Furthermore increasing prices and question over the availability of diesel fuel derived from crude oil has introduced a growing interest. Hence it is most likely that future diesel engines will be operated on pure biodiesel and/or blends of biodiesel and crude oil-based diesel. In this study the performance of different biodiesel blends under low temperature combustion conditions (i.e., high exhaust gas recirculation and advanced fuel injection schemes) was investigated.

Two advanced combustion models have been validated with the KIVA-3V Release 2 code in the context of two-stage combustion in a heavy duty diesel engine. The first model uses CHEMKIN to directly integrate chemistry in each computational cell. The second model accounts for flame propagation with the G-equation, and CHEMKIN predicts autoignition and handles chemistry ahead of and behind the flame front. A Damköhler number criterion was used in flame containing cells to characterize the local mixing status and determine whether heat release and species change should be a result of flame propagation or volumetric heat release. The purpose of this criterion is to make use of physical and chemical time scales to determine the most appropriate chemistry model, depending on the mixture composition and thermodynamic properties of the gas in each computational cell.