Search Results

Real gas effects are studied during the compression stroke of a diesel engine. Several different real gas models are compared to the ideal gas law and to the experimental pressure history. Comparisons are done with both 1-D and CFD simulations, and reasons and answers are found out for the observed differences between simulations and experimental data. The engine compression ratio was measured for accurate model predictions. In addition, a 300bar extreme pressure case is also analyzed with the real gas model since an engine capable for this performance level is currently being built at the Aalto University School of Science and Technology. Real gas effects are even more important in these extreme conditions than in normal operating pressures. Finally, it is shown that the predicted pressure history during an engine compression stroke by a real gas model is more accurately predicted than by the ideal gas law.

Knocking combustion is a major obstacle towards engine downsizing and boosting—popular techniques towards meeting the increasingly stringent emission standards of SI engines. The commercially available gasoline is a mixture of many chemical compounds like paraffins, isoparaffins, olefins and aromatics⁠. Therefore, the modeling of its combustion process is a difficult task. Additionally, the blends of certain compounds exhibit non-linear behavior in comparison to the pure components in terms of knock resistance. These facts require further analysis from the perspective of combustion chemistry. The present work analyses the effects of blending ethanol to FACE-C gasoline. A range of pressures, temperatures, and equivalence ratios has been considered for this purpose. The open source softwares Cantera version 2.4.0 and OpenSMOKE++ Suite have been used for the simulations.

Over the past few years, the growing concerns about global warming and efforts to reduce engine-out emissions have made the dual-fuel (DF) engines more popular in marine and power industries. The use of natural gas as an alternative fuel in DF engines has both the environmental and economic advantages over the conventional diesel combustion. However, the misfire phenomenon at lean conditions limits the operating range of DF combustion and causes emissions of unburned hydrocarbon (UHC) and unburned methane (methane-slip) in the environment. The greenhouse effect of methane is considered 28 times greater than CO2 over a 100-year perspective, which raises concerns for the governments and marine engine manufacturers. In efforts to reduce the UHC and methane-slip from DF engines, this study discusses ethane enrichment of diesel-methane DF combustion in a full-metal single-cylinder research engine under lean condition (λGFB = ~2.0) while keeping the total-fuel energy rather constant.

The direct injection (DI) natural gas engine is considered as one of the promising technologies to achieve the continuing goals of the higher efficiency and reduced emissions for internal combustion engines. Shock wave phenomena can easily occur near the nozzle exit when high pressure gaseous fuel is injected directly into the engine cylinder. In the present study, high pressure gas issuing from a prototype gas injector was experimentally studied using planar laser-induced fluorescence (PLIF) technique. Acetone was selected as a fuel tracer. The effects of injection pressures on the flow structure and turbulent mixing were investigated based on a series of high resolution images. The jet macroscopic structures, such as jet penetration, cone angle and jet volume, are analyzed under different injection pressures. Results show that barrel shock waves can significantly influence the jet flow structure and turbulent mixing.

As CO2 emissions from traffic must be reduced and fossil-based traffic fuels need to phase out, bio-based traffic fuels alone cannot meet the future demand due to their restricted availability. Another way to support fossil phase-out is to include synthetic fuels that are produced from circular carbon sources with renewable energy. Several different fuel types have been proposed, while, methanol only requires little processing from raw materials and could be used directly or as a drop-in fuel for some of the current engine fleet. CO2 emissions arising from fuel production are significantly reduced for synthetic renewable methanol compared to the production of fossil gasoline. Methanol has numerous advantages over the currently used fossil fuels with high RON and flame speed in spark-ignition engines as well as high efficiency and low emissions in combustion ignition engines.

The flow through the valves of an engine cylinder head is very complex in nature due to very high gas velocities and strong flow separation. However, it is also the typical situation in almost every engine related flow. In order to gain better understanding of the flow features after the cylinder head, and to gain knowledge of the performance level that can be expected from CFD analysis, flow field measurements and computations were made in an engine rig. Particle image velocimetry (PIV) and paddle wheel measurements have been conducted in a static heavy-duty diesel engine rig to characterize the flow features with different valve lifts and pressure differences. These measurements were compared with CFD predictions of the same engine. The simulations were done with the standard k-ε turbulence model and with the RNG turbulence model using the Star-CD flow solver.

The study aims at providing more accurate initial conditions for turbulence prior to combustion with the help of a four valve, large bore diesel engine CFD model. Combustion simulations are typically done with a sector mesh and initial turbulence in these simulations is usually taken from relatively inaccurate correlations. This study also aims at developing a more accurate initial turbulence correlation for combustion simulations. A one-dimensional model was first used to provide boundary conditions as well as the initial flow conditions at the beginning of the simulation. Steady state and transient boundary conditions were studied. Also, the standard κ - ε and RNG/κ - ε turbulence models were compared. From the averaged values of turbulence kinetic energy and its dissipation rate over the cylinder volume, a re-tuned correlation for defining the initial turbulent conditions at bottom dead center (BDC) prior to the compression stroke is proposed.

The development of new high power diesel engines is continually going for increased mean effective pressures and consequently increased thermal loads on combustion chamber walls close to the limits of endurance. Therefore accurate CFD simulation of conjugate heat transfer on the walls becomes a very important part of the development. In this study the heat transfer and temperature on piston surface was studied using conjugate heat transfer model along with a variety of near wall treatments for turbulence. New wall functions that account for variable density were implemented and tested against standard wall functions and against the hybrid near wall treatment readily available in a CFD software Star-CD.

Renewable diesel-type fuels and their compatibility with a single-cylinder medium-speed research diesel engine were studied. The report consists of a literature study on the fuels, introduction of the simulation model designed and simulations made, and of the results and summary sections. The fuels studied were traditional biodiesel (fatty acid methyl ester, FAME), hydrotreated vegetable oil (HVO), Fischer-Tropsch (FT) diesel fuels and dimethyl ether (DME). According to the simulations, the behaviors of different renewable diesel fuels in the fuel injection system are quite similar to one another, with the greatest deviations found with DME. The main differences in the physical properties are fuel densities and viscosities and especially with DME compressibility, which have some predictable effect. The chemical properties of the fuels are more critical for a common rail fuel injection system.

A new variable density / physical property wall function formalism has been developed. The new formalism is designed to extend the validity range of wall functions to cover both the low- and high-Reynolds-number domains so that the restrictions on the non-dimensional near-wall mesh resolution can be avoided. The new formalism also accounts for the temperature gradient induced variations of density, viscosity, heat conductivity and specific heat capacity. The new wall function formalism is constructed in conjunction with a modified low-Reynolds-number turbulence model in order to avoid the conflicting requirements of low- and high-Reynolds-number models on the near wall mesh resolution. The new formulation is validated with test simulations of strongly heated air flows in circular tube against measurements and Direct Numerical Simulation (DNS) results.

Experimental spray tip penetrations obtained from a large-bore medium-speed optical diesel engine were compared to CFD simulations. The optical spray results are unique as they are obtained from a running large-bore (200mm) diesel engine. The experimental spray tip penetration measurements were obtained during the early spray development period when the spray evaporation had not yet reached the quasi steady-state phase. The CFD simulations were conducted in both static chamber environment and in engine conditions. The fuel injection boundary conditions were obtained from 1-D simulations. Within the error margins associated with the experimental and computational data, relatively good accuracy was obtained between measured and simulated spray tip penetration. It was also observed that it is very important to have accurate fuel injection mass flow rate data. This was observed after a sensitivity analysis was made for the injection duration and fuel mass quantity.

The one-equation subgrid scale model for the Large Eddy Simulation (LES) turbulence model has been compared to the popular k-ε RNG turbulence model in very different sized direct injection diesel engines. The cylinder diameters of these engines range between 111 and 200 mm. This has been an initial attempt to study the effect of LES in diesel engines without any modification to the combustion model being used in its Reynolds-averaged Navier-Stokes (RANS) form. Despite some deficiencies in the current LES model being used, it already gave much more structured flow field with approximately the same kind of accuracy in the cylinder pressure predictions than the k-ε RNG turbulence model.

In the present study, a new approach for modelling emissions of coke particles or cenospheres from large diesel engines using HFO (Heavy fuel oil) was studied. The model used is based on a multicomponent droplet mass transfer and properties model that uses a continuous thermodynamics approach to model the complex composition of the HFO fuel and the resulting evaporation behavior of the fuel droplets. Cenospheres are modelled as the residue left in the fuel droplets towards the end of the simulation. The mass-transfer and fuel properties models were implemented into a cylinder section model based on the Wärtsilä W20 engine in the CFD-code Star CD v.4.24. Different submodels and corresponding parameters were tuned to match experimental data of cylinder pressures available from Wärtsilä for the studied cases. The results obtained from the present model were compared to experimental results found in the literature.

In this study, one-dimensional fluid dynamics simulation software was utilized in producing common rail diesel fuel injection for varying injection parameters with enhanced accuracy. Injection modeling refinement is motivated by improved comprehension of the effects of various physical phenomena within the injector. In addition, refined injection results yield boundary conditions for three-dimensional CFD simulations. The criteria for successful simulation results were evaluated upon experimental test run data that have been reliably obtained, primarily total injected mass per cycle. A common rail diesel fuel delivery system and its core mechanics were presented. System factors most critical to fuel delivery were focalized. Models of two solenoid-type common rail injectors of different physical sizes and applications were enhanced.

This paper aims to study numerically the influence of the number of fuel sprays in a single-cylinder diesel engine on mixing and combustion. The CFD simulations are carried out for a heavy-duty diesel engine with an 8 hole injector in the standard configuration. The fuel spray mass-flow rate was obtained from 1D-simulations and has been adjusted according to the number of nozzle holes to keep the total injected fuel mass constant. Two cases concerning the modified mass-flow rate are studied. In the first case the injection time was decreased whereas in the second case the nozzle hole diameter was decreased. In both cases the amount of nozzle holes (i.e. fuel sprays) was increased in several steps to 18 holes. Quantitative analyses were performed for the local air-fuel ratio, homogeneity of mixture distribution, heat release rate and the resulting in-cylinder pressure.

The CFD simulation of diesel combustion needs as accurate initial values as possible to be reliable. In this paper the effect of spatial distribution of state and turbulence values at intake valve closure to those distributions prior to SOI is studied. Totally five cases of intake and compression stroke simulations are run. The only change between cases is the intake boundary condition of turbulence. In the last case the average values of p, T, k, ε and swirl number at intake valve closure are used as initial values to compression simulation. The turbulence in the engine cylinder is mainly generated in the very fast flow over the intake valves. In this paper the effect of boundary conditions of turbulence to its level at intake valve closure is studied. Several cases are simulated with different boundary conditions of turbulence. Also the swirl number is compared to experimental value.

Natural gas has been considered as one promising alternative fuel for internal combustion (IC) engines to meet strict engine emission regulations and reduce the dependence on petroleum oil. Although compressed natural gas (CNG) intake manifold injection has been successfully applied into spark ignition (SI) engines in the past decade, natural gas direct injection compression ignition (DICI) engine with new injection system is being pursued to improve engine performance. Gas jet behaves significantly different from liquid fuels, so the better understanding of the effects of gas jet on fuel distribution and mixing process is essential for combustion and emission optimization. The present work is aimed to gain further insight into the characteristics of low pressure gas jet. An experimental gas jet investigation has been successfully conducted using tracer-based planar laser-induced fluorescence (PLIF) technique. For safety reason, nitrogen (N₂) was instead of CNG in this study.

Dual-fuel technology is suggested as a solution for effectively utilizing alternative fuel types in the near future. Charge air mixed methane combined with a compression ignition engine utilizing a small diesel pilot injection seems to form a worthwhile compromise between good engine efficiency and low emission outcome. Problems concerning dual-fuel technology profitableness seems to be related to fully control the combustion in relation to lean conditions. Lean operating conditions solves the problems concerning pumping losses, but brings challenges in controlling the slow heat release of the premixed methane-air mixture. In the present work, a single cylinder ‘free parameter’ diesel engine was adapted for dual-fuel (diesel-methane) usage. A parameter study related to lambda window widening possibilities was carried out.

Dual fuel (DF) combustion technology as a feasible approach controlling engine-out emissions facilitates the concept of fuel flexibility in diesel engines. The abundance of natural gas (90-95% methane) and its relatively low-price and the clean-burning characteristic has attracted the interest of engine manufacturers. Moreover, with the low C/H ratio and very low soot producing tendency of methane combined with high engine efficiency makes it a viable primary fuel for diesel engines. However, the fundamental knowledge on in-cylinder combustion phenomena still remains limited and needs to be studied for further advances in the research on DF technology. The objective of this study is to investigate the ignition delay with the effect of, 1) methane equivalence ratio, 2) intake air temperature and 3) pilot ratio on the diesel-methane DF-combustion. Combustion phenomenon was visualized in a single cylinder heavy-duty diesel engine modified for DF operations with an optical access.

Measurements have been done in order to obtain information concerning the effect of EGR for the smoke and NOx emissions of a heavy-duty diesel engine. Measured smoke number and NOx emissions are explained using detailed chemical kinetic calculations and CFD simulations. The local conditions in the research engine are analyzed by creating equivalence ratio - temperature (Phi-T) maps and analyzing the CFD results within these maps. The study uses different amounts of EGR and the standard EN590 diesel fuel. The detailed chemical kinetic calculations take into account the different EGR rates. The CFD calculations are made with a flamelet-based combustion model together with detailed chemistry. The results are compared to a previous study where a hybrid local flame area evolution model combined with an eddy breakup - type model was used in the CFD simulations.