Search Results

Included in this document are requirements for conveyor systems, guides, stops, restraint hardware that are used on trucks, transporters, dollies, storage provisions, pallet build-up hoists, or other device-handling equipment. These requirements reflect state of the art criteria applied to known successfully operated hardware. Any design deviations shall be required to demonstrate equivalency to this specification criteria.

Included in this document are requirements for conveyor systems, guides, stops, restraint hardware that are used on trucks, transporters, dollies, storage provisions, pallet build-up hoists, or other device-handling equipment. a) These requirements reflect state of the art criteria applied to known successfully operated hardware. Any design deviations shall be required to demonstrate equivalency to this specification criteria. b) These devices usually form an integral part of the aircraft and as such are subject to regulatory agencies' requirements to assure structural integrity.

This SAE Aerospace Recommended Practice (ARP) specifies requirements for those portions of the aircraft Unit Load Device ground and terminal handling equipment that will have a direct bearing on the life of the ULD for the purpose of preventing undue wear on the ULD. Past experience has shown that in-service defects in regard to the above equipment cause high ULD cost. Greater control of maintenance is required.

This SAE Aerospace Recommended Practice (ARP) specifies requirements for those portions of the aircraft Unit Load Device ground and terminal handling equipment that will have a direct bearing on the life of the ULD for the purpose of preventing undue wear on the ULD. Past experience has shown that in-service defects in regard to the above equipment cause high ULD cost. Greater control of maintenance is required.

This SAE Aerospace Standard (AS) covers the design, fabrication, performance and operational testing requirements for lower deck containers for use in main line aircraft which do not require airworthiness certification when loaded under the conditions of compartment restraint and in accordance with the aircraft's Weight and Balance Manual and/or, where applicable according to the aircraft type's approved Weight and Balance Manual, AS36100A or NAS 3610 equivalent base plate restraint for these containers. Most sizes of containers covered by this document (base sizes K, L, P, and Q) cannot physically be loaded and latched on aircraft main deck cargo systems. Base size A and M containers can, but are not allowed on aircraft main decks, which do not accept non-certified units. Accordingly, all containers covered by this document are to be used/installed exclusively in aircraft lower deck compartments.

This SAE Aerospace Standard (AS) covers the requirements for three sizes of compartment restrained lower deck containers (unit load devices) for the 767 airplane and which do not require airworthiness certification. NOTE: IATA Specification 50/0, General Technical Requirements and Serviceability limits, should also be taken into account when designing and making equipment according to this specification as certain provisions contained therein will also be applicable.

This AS covers the requirements for three sizes of compartment restrained lower deck containers (Unit Load Devices) for the 767 airplane and which do not require airworthiness certification.

This AS covers the requirements for three sizes of compartment restrained lower deck containers (Unit Load Devices) for the 767 airplane and which do not require airworthiness certification. NOTE: IATA Specificaton 50/0, General Technical Requirements and Serviceability limits, should also be taken into account when designing and making equipment according to this Specification as certain provisions contained therein will also be applicable.

This SAE Aerospace Standard (AS) covers the requirements for lower deck containers in wide body and standard body aircraft which do not require airworthiness certification under the condition of compartment restraint and/or, where applicable according to aircraft type, NAS3610 equivalent baseplate-restraint for these containers. NOTE: IATA 50/0, “Requirements for interlining of ULDs”, should also be taken into account when designing and making equipment.

This document establishes dimensional, structural and environmental requirements for 1.5G interline pallets.

This document establishes dimensional, structural and environmental requirements for two types of interline pallets. Type II covers NAS 3610 code sizes and Type III covers other sizes not currently included in NAS 3610.

The tests are static in nature to minimize complexity and cost of required testing facilities. As far as practical, applied static loads should take into account the combined static and dynamic loads anticipated in service.

The tests are static in nature to minimize complexity and cost of required testing facilities. As far as practical, applied static loads should take into account the combined static and dynamic loads anticipated in service.

This SAE Aerospace Standard (AS) details the design of fork pockets on containers and equipment for use with pallet lift trucks and forklift trucks.