Refine Your Search

Topic

Search Results

Standard

Wheel Chocks

1996-07-01
HISTORICAL
AIR4905
The purpose of this document is to present general considerations for the design and use of aircraft wheel chocks. The design and use of aircraft wheel chocks is a good deal more complicated than it may appear at first glance.
Standard

400 Hz CONNECTION AIRCRAFT ELECTRICAL MAINTENANCE PROCEDURES

1994-12-01
HISTORICAL
AIR4365
This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.
Standard

400-CYCLE GROUND POWER UNIT PROVISIONS FOR AIRCRAFT ELECTRICAL SYSTEM PROTECTION

2002-12-16
CURRENT
ARP760
This SAE Recommended Practice which defines the terms and tabulates the limits of the characteristics for various protective devices used in conjunction with 400-cycle ground power for civil aircraft is intended to assist the airlines in standardizing on 400-cycle protective systems. The limits found to be acceptable in the civil aircraft industry are presented.
Standard

Chassis Mounted Lifts Used to Board Airline Passengers With Mobility Impairments

1999-07-01
HISTORICAL
ARP5141
This SAE Aerospace Recommended Practice (ARP) is intended to recommend a minimum standard, for the design and manufacturer of a self-propelled, chassis mounted passenger boarding vehicle. The vehicle will permit safe operation while minimizing aircraft damage and personnel safety hazards associated with commercial aircraft boarding operations. The vehicle described is intended to be used for assisting wheelchair passengers and passengers with disabilities on and off aircraft with door sill heights of 60 in (152.4 cm) and above.
Standard

Chassis Mounted Lifts Used to Board Airline Passengers With Mobility Impairments

2014-03-11
CURRENT
ARP5141A
This SAE Aerospace Recommended Practice (ARP) is intended to recommend a minimum standard, for the design and manufacturer of a self-propelled, chassis mounted passenger boarding vehicle. The vehicle will permit safe operation while minimizing aircraft damage and personnel safety hazards associated with commercial aircraft boarding operations. The vehicle described is intended to be used for assisting wheelchair passengers and passengers with disabilities on and off aircraft with door sill heights of 60 in (152.4 cm) and above.
Standard

Design Specification for Towbarless Tow Vehicles

2013-01-04
HISTORICAL
ARP4853C
The tow vehicle should be designed for towbarless movement of aircraft on the ground. The design will ensure that the unit will safely secure the aircraft nose landing gear within the coupling system for any operational mode.
Standard

Aircraft Markings for Ground Support Equipment alignment

2015-10-23
WIP
AS6896
Definition of target design and location on aircraft, that will be used: - To provide correct GSE alignment support and docking when approaching the aircraft in automatic, semi-automatic or manual mode - by GSE autoleveling system to detect and follow aircraft vertical movements
Standard

SOLID-STATE FREQUENCY CONVERTER 400 HERTZ, 3-PHASE OUTPUT

1989-09-01
HISTORICAL
ARP1940
This specification covers the requirements for solid-state frequency converters with 480 [or 380] V 3-phase, 60 [or 50] Hz input and 115/200 V, 3-phase, 400 Hz output capable of powering aircraft type loads requiring MIL-STD-704D quality power. The frequency converter shall be a self-contained unit suitable for the environment of intended use. Typical applications include dedicated use at passenger loading bridges (mounted under the bridge in telescoping bridge applications or fixed installation at base of stationary type loading bridges) with weatherproof enclosures or hangar/lab use where indoor fixed or portable units can be used.
Standard

Aircraft Tow Bar

2005-04-06
HISTORICAL
ARP1915C
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design considerations for transport aircraft tow bars. It does not cover the requirements for tow bars intended for aircraft with a maximum ramp mass (MRW) below 8,600 kg (19,000 lb).
Standard

Aircraft Tow Bar

2018-09-18
WIP
ARP1915F
This SAE Aerospace Recommended Practice (ARP) specifies dimensional and physical requirements of tow bar connections to tractor and aircraft (see Figure 1). It is applicable to all types of commercial transport category aircraft tow bar. The purpose of this SAE Aerospace Recommended Practice (ARP) is to standardize tow bar attachments to airplane and tractor according to the mass category of the towed aircraft, so that one tow bar head with different shear levels can be used for all aircraft that are within the same mass category and are manufactured in compliance with AS1614 or ISO 8267.
Standard

Aircraft Tow Bar

2010-09-13
HISTORICAL
ARP1915D
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design considerations for transport aircraft tow bars. It does not cover the requirements for tow bars intended for aircraft with a maximum ramp mass (MRW) below 8600 kg (19 000 lb).
Standard

Aircraft Tow Bar

2016-05-06
CURRENT
ARP1915E
This SAE Aerospace Recommended Practice (ARP) specifies dimensional and physical requirements of tow bar connections to tractor and aircraft (see Figure 1). It is applicable to all types of commercial transport category aircraft tow bar. The purpose of this SAE Aerospace Recommended Practice (ARP) is to standardize tow bar attachments to airplane and tractor according to the mass category of the towed aircraft, so that one tow bar head with different shear levels can be used for all aircraft that are within the same mass category and are manufactured in compliance with AS1614 or ISO 8267.
Standard

Aircraft Towbar

1997-12-01
HISTORICAL
ARP1915B
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design considerations for aircraft towbars.
Standard

ELECTRICAL CONNECTORS FOR USE IN BATTERY POWERED GROUND SUPPORT EQUIPMENT

1985-07-01
HISTORICAL
ARP1892
This recommended practice describes a two-pole electric connector for use in battery powered ground support equipment i.e. traction batteries. Alternatively, the connector can have two or more auxiliary contacts for auxiliary circuits. A handle may be added as an option to assist in connecting and disconnecting.
Standard

Electrical Connectors for Use in Battery Powered Ground Support Equipment

1997-12-01
CURRENT
ARP1892B
This SAE Aerospace Recommended Practice (ARP) describes a two-pole electric connector for use in battery powered ground support equipment, i.e., traction batteries. Alternatively, the connector can have two or more auxiliary contacts for auxiliary circuits. A handle may be added as an option to assist in connecting and disconnecting.
Standard

ELECTRICAL CONNECTORS FOR USE IN BATTERY POWERED GROUND SUPPORT EQUIPMENT

1991-04-29
HISTORICAL
ARP1892A
This recommended practice describes a two-pole electric connector for use in battery powered ground support equipment, i.e., traction batteries. Alternatively, the connector can have two or more auxiliary contacts for auxiliary circuits. A handle may be added as an option to assist in connecting and disconnecting.
Standard

Minimum Safety Requirements for Special Purpose Airline Ground Support Equipment

2014-05-29
CURRENT
AIR1375D
This document applies to special purpose equipment which is used in the ground handling, servicing, and maintenance of transport aircraft. Fixed airport facilities and equipment covered under other sections of Part 1910 of Code of Federal Regulations (OSHA) are excluded from the scope of this document.
X