Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Bumper Jack Requirements--Motor Vehicles

1967-01-01
HISTORICAL
J979_196701
The following requirements and test information can be used to obtain reasonable quality and uniformity for bumper jacks. For this specification, a fully loaded vehicle includes curb weight, optional equipment, weight at 150 lb each for specified number of passengers, and a 150 lb load in the trunk. Vehicles with a gvw rating will be loaded to the maximum specified gvw.
Standard

Ship Systems and Equipment--Part Standard for Studs--Continuous and Double End (Inch Series)

2009-01-23
HISTORICAL
J2271_200901
This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a. Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: - UNRC threads (0.190 through 4 inches) - UNRF threads (0.190 through 1-1/2 inches) - 8UNR threads (1-1/8 through 4 inches) b. Double end studs (clamping type) where both ends are of the same thread length in the following threads and diameters: - UNRC threads (1/4 through 4 inches) - UNRF threads (1/4 through 1-1/2 inches) - 8UNR threads (1-1/8 through 4 inches) c.
Standard

Ship Systems and Equipment - Part Standard for Studs - Continuous and Double End (Inch Series)

2004-06-21
HISTORICAL
J2271_200406
This SAE Parts Standard provides dimensional and quality assurance requirements for 1/4 through 2 in sizes of studs in the following configurations in standard materials used for ship system applications: a. Continuous thread studs in UNRC and 8UNR series. b. Double end studs (clamping type) where both ends are of the same thread series (UNRC or 8UN). Also called bolt-studs. (These are suitable for mating with nuts or the set end may be installed with anaerobic thread locking compound.) c. Double end studs (interference thread type) with the nut end having UNRC or 8UNR series thread and where the tap end has NC 5 HFS interference fit thread forms. Also called a tap end stud. A complete metric companion to this document is provided in SAE J2271M, therefore no metric equivalents are presented. These studs are primarily or use in ship systems and equipment.
Standard

Torque Ratings for Power Take-off Mounting Pads

2003-07-25
HISTORICAL
J2662_200307
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
Standard

TOOL AND DIE STEELS

1970-05-01
HISTORICAL
J438_197005
This standard covers the identification, classification, and chemical composition of tool and die steels for use by engineers, metallurgists, tool designers, tool room supervisors, heat treaters, and tool makers.
Standard

Tool and Die Steels

2018-01-09
CURRENT
J438_201801
This standard covers the identification, classification, and chemical composition of tool and die steels for use by engineers, metallurgists, tool designers, tool room supervisors, heat treaters, and tool makers.
Standard

Selection and Heat Treatment of Tool and Die Steels

1970-04-01
HISTORICAL
J437A_197004
The information in this report covers data relating to SAE J438, Tool and Die Steels, and is intended as a guide to the selection for the steel best suited for the intended purpose and to provide recommended heat treatments and other data pertinent to their use. Specific requirements as to physical properties are not included because the majority of tool and die steels are either worked or given special heat treatments by the purchaser. The purchaser may or may not elect to use the accompanying data for specification purposes.
Standard

Tool and Die Steels

1970-05-01
HISTORICAL
J438B_197005
This standard covers the identification, classification, and chemical composition of tool and die steels for use by engineers, metallurgists, tool designers, tool room supervisors, heat treaters, and tool makers.
Standard

VOLTAGES FOR DIESEL ELECTRICAL SYSTEMS

1993-11-23
CURRENT
J539_199311
This SAE Recommended Practice is intended to apply to lamps, batteries, heaters, radios, and similar equipment for operation with mobile or automotive diesel engines. Twenty-four V systems have long been used for heavy-duty services because 24 V permit operating 12 V systems in series-parallel. Thirty-two V systems have been used for marine, railroad-car lighting, and other uses. Generators, storage batteries, starting motors, lighting, and auxiliary electrical equipment shall be for nominal system ratings of 12, 24, or 32 V as determined by the power requirements of the application. It is recommended that no intermediate voltages be considered. The combination of a 24 V starting motor and two 12 V batteries connected in series for cranking is considered practical where it can be adapted to the installation.
Standard

Standard of Purity for Recycled R-134a (HFC-134a) and R-1234yf (HFO-1234yf) for Use in Mobile Air-conditioning Systems

2012-04-10
CURRENT
J2099_201204
This SAE Standard applies to: recycled R-134a refrigerant, used in servicing of motor vehicle air conditioning (A/C) systems that were designed for use with R-12 and have been retrofitted for use with R-134a; recycled R-134a refrigerant, used in servicing of motor vehicle air conditioning (A/C) systems that were designed for use with R-134a; recycled R-1234yf refrigerant, used in servicing of motor vehicle air conditioning (A/C) systems that were designed for use with R-1234yf. Hermetically sealed, refrigerated cargo systems are not covered by this document.
Standard

Drawbars--Crawler Tractor

2002-02-21
CURRENT
J749_200202
This SAE Standard provides recommended dimensions for drawbars for crawler tractors as defined in SAE J1057 (SEP88). It includes only those dimensions which will affect the attaching of towed equipment.
Standard

Vehicle Jack Requirements and Test Procedures

1996-05-01
HISTORICAL
J1884_199605
The scope of this SAE Recommended Practice is restricted to the testing of jacks supplied as original equipment on passenger cars, light trucks, and vans. To this end, both component suppliers and vehicle manufacturers are guided in the proper design and testing of jacks. The purpose of this document is to provide a test procedure that can be used to ensure reasonable quality and uniformity for vehicle jacks as supplied as original equipment.
X