Refine Your Search

Date

Date

Topic

Topic

Suppliers Technical review MTC1, Earthmoving Machinery Quality, Reliability, and Durability

Search Results

Viewing 1 to 20 of 24
12Next >Last >>
Sort by relevance
Standard

Cutting Edge—Optional Cross-Sections and Dimensions Loader Straight
2006-02-05
HISTORICAL
J1581_200602
The purpose of this SAE Recommended Practice is to specify dimensions for loader straight cutting edge cross sections without holes and with bolt holes for mounting bolt-on teeth and tooth adaptors on loader buckets described by SAE J731. This recommended practice is intended to supplement SAE J1303 and SAE J1304 with cross sections for heavier duty applications, by identifying larger blunts, greater bevel angles, larger bolt holes, and greater bolt spacing.
Standard

Hole Spacing for Scraper and Dozer Cutting Edges
2006-02-01
HISTORICAL
J737_200602
This standard is intended for cutting edge sections used on: a Tractor-scrapers as described in SAE J1057 and J728. b Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation.
Standard

CAPACITY RATING—ELEVATING SCRAPERS
1993-06-01
HISTORICAL
J957_199306
This SAE Standard specifies a procedure for approximating the volume of a typical material carried in the bowl of an elevating scraper as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and a representative volume on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.
Standard

IDENTIFICATION TERMINOLOGY—PIPELAYERS
1980-06-01
HISTORICAL
J1295_198006
This standard applies to machines which are designed to raise, lower, and carry pipe and loads of similar nature. The term pipelayer does not include tractors or loaders with side booms which are optional attachments, manufacturer or dealer-installed, to machines as defined in SAE J1057. Note: Some related standards will apply equally to pipelayers and to tractors and loaders with side boom. Two such standards are SAE J743 and ANSI B30.14.
Standard

Travel Performance and Rating Procedure, Crawler Mounted Hydraulic Excavators, Material Handlers, Knuckle Boom Log Loaders, and Certain Forestry Equipment
2012-01-06
CURRENT
J1309_201201
This SAE Standard describes a uniform method to calculate and specify travel performance characteristics of hydraulic excavators, material handlers, knuckle boom log loaders, delimbers, feller bunchers, harvesters, processors, and other knuckle boom material handlers. It establishes definitions and specifies machine conditions for calculations and tests. This document applies to crawler mounted machines such as hydraulic excavators as defined in SAE J/ISO 6165 and ISO 7135, and knuckle boom log loaders as defined in SAE J1209 and SAE J2055. This document also applies to certain forestry equipment defined in SAE J1209 and ISO 6814 that have crawler mountings such as delimbers, feller bunchers, harvesters, and processors. Included in the definition of hydraulic excavators are also front shovel, clamshell, and telescoping boom excavators.
Standard

Loading Ability Test Procedure - Scrapers
2011-10-27
CURRENT
J764_201110
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
Standard

Cutting Edge—Cross Sections Loader Straight
2006-02-05
HISTORICAL
J1303_200602
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85.
Standard

Cutting Edge - Cross Sections Loader Straight
2011-10-25
CURRENT
J1303_201110
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85. NOTE—For some heavy duty applications, cross sections with larger blunts and greater bevel angles may be required.
Standard

Cutting Edge—Cross Sections Loader Straight with Bolt Holes
2006-02-05
HISTORICAL
J1304_200602
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters.
Standard

Cutting Edge - Cross Sections Loader Straight with Bolt Holes
2011-10-25
CURRENT
J1304_201110
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters. NOTE—For some heavy-duty applications, cross sections with larger blunts, greater bevel angles, and larger bolt holes may be required.
Standard

Lift Capacity Calculation Method Scrap and Material Handlers
2019-04-15
CURRENT
J2518_201904
This SAE Standard provides a uniform method to calculate the lift capacity of scrap and material handlers, establishes definitions and specifies machine conditions for the calculations. This document applies to scrap and material handlers as defined in SAE J2506 that have a 360 degrees continuous rotating upper structure. It does not apply to equipment that is incapable of lifting a load completely off the ground. This document applies to those machines that are crawler, wheel, rail and pedestal or stationary mounted.
Standard

Cutting Edge—Curved Grader
2006-02-05
HISTORICAL
J739_200602
This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580.
Standard

Earthmoving Machinery—Coupling of Attachments to Skid Steer Loaders
2000-06-28
HISTORICAL
J2513_200006
This SAE Standard sets forth standard dimension requirements for the loader attachment bracket and attachment interface to allow interchangeability of attachments on skid steer loaders whose operating mass (see SAE J/ISO 6165) is 4,500 kg or less. Narrow skid steer loaders may have a width that does not allow compliance with this standard. The design of the loader attachment bracket locking system is not restricted by this standard and is left to the discretion of the manufacturer.
12Next >Last >>
X