Search Results

Standard

Numbering Systems for End Mills

2019-10-09

CURRENT

J2342_201910

This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering Systems for End Mills

1999-01-20

HISTORICAL

J2342_199901

This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Film Analysis Guides for Dynamic Studies of Test Subjects

2019-10-02

CURRENT

J138_201910

This SAE Recommended Practice is intended to provide guidelines for the identification of subjects used in dynamic tests. It establishes recommendations for location and description of target areas on test subjects or test devices, as well as recommendations for photographic calibration and timing.

Standard

FILM ANALYSIS GUIDES FOR DYNAMIC STUDIES OF TEST SUBJECT

1969-12-01

HISTORICAL

J138_196912

This SAE Recommended Practice is intended to provide guidelines for the identification of subjects used in dynamic tests. It establishes recommendations for location and description of target areas on test subjects or test devices, as well as recommendations for photographic calibration and timing.

Standard

Seat Belt Hardware Performance Requirements

2013-02-13

HISTORICAL

J141_201302

This SAE Recommended Practice describes performance requirements for hardware used in motor vehicle seat belt assemblies when tested in accordance with the test procedures specified in SAE J140. Test procedures and performance requirements for retractors will be covered in separate SAE Recommended Practices to be issued later.

Standard

OEM Plastic Parts Repair

2019-10-24

CURRENT

J1573_201910

This SAE Recommended Practice defines the information required to repair the various types of plastics found on modern light-duty highway vehicles. Information is included for the repair and refinishing of most plastic body parts, both interior and exterior. Repair information is described for all commonly used plastics including, but not limited to, polyurethanes, polycarbonate blends, modified polypropylenes, polyethylenes and nylons. Repairs can be made to these types of plastics using two-part (2K) repair adhesives, plastic welding, and other materials available from body shop suppliers. When a new type of plastic is being introduced to the market through a new vehicle program, specific repair and refinishing procedures should be provided, following the format in this document. Sheet-molded compounds (SMC), fiber-reinforced plastics (FRP) and carbon fiber reinforced plastics can also be repaired using slightly different procedures and repair materials.

Standard

OEM Plastic Parts Repair

2011-12-20

HISTORICAL

J1573_201112

This SAE Recommended Practice defines the information required to repair the various types of plastics found on modern light-duty highway vehicles. Information is included for the repair and refinishing of most plastic body parts, both interior and exterior. Repair information is described for all commonly used plastics including, but not limited to, polyurethanes, polycarbonate blends, modified polypropylenes, polyethylenes and nylons. Repairs can be made to these types of plastics using two-part (2K) repair adhesives, plastic welding, and other materials available from body shop suppliers. When a new type of plastic is being introduced to the market through a new vehicle program, specific repair and refinishing procedures should be provided, following the format in this document. Sheet-molded compounds (SMC), fiber-reinforced plastics (FRP) and carbon fiber reinforced plastics can also be repaired using slightly different procedures and repair materials.

Standard

NUMBERING SYSTEM FOR REAMERS

1990-11-01

HISTORICAL

J2124_199011

This SAE Recommended Practice provides a systematic method for the identification of various types of hand, machine, and shell reamers used in industrial applications. When used as recommended in this report, the numbering system will assist in obtaining consistent reamer descriptions in communications. The report was developed in cooperation with the Automotive Industry Action Group (AIAG).

Standard

Numbering System for Single Diameter and Taper Reamers

2019-10-09

CURRENT

J2124_201910

This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Single Diameter and Taper Reamers

1998-10-14

HISTORICAL

J2124_199810

This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

NUMBERING SYSTEM FOR SINGLE DIAMETER DRILLS

1994-04-01

HISTORICAL

J2122_199404

This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools.

Standard

NUMBERING SYSTEM FOR STANDARD DRILLS

1990-11-01

HISTORICAL

J2122_199011

This SAE recommended practice provides a systematic method for the identification of standard drills. It is intended to assist in the cataloging and supplying of these tools. The report was developed in cooperation with the Automotive Industry Action Group (AIAG).

Standard

Numbering System for Single Diameter Drills

2019-10-09

CURRENT

J2122_201910

This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying drills that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Single Diameter Drills

1998-10-14

HISTORICAL

J2122_199810

This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying drills that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Multiple Diameter Cutting Tools

2019-10-09

CURRENT

J2276_201910

This SAE Recommended Practice provides a systematic method for the identification of multiple diameter cutting tools. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Multiple Diameter Cutting Tools

1998-10-13

HISTORICAL

J2276_199810

This SAE Recommended Practice provides a systematic method for the identification of multiple diameter cutting tools. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

NUMBERING SYSTEM FOR STANDARD TAPS

1990-11-01

HISTORICAL

J2123_199011

This SAE Recommended Practice provides a systematic method for the identification of standard taps. It is intended to assist in the cataloging and supplying of these tools. The report was developed in cooperation with the Automotive Industry Action Group (AIAG).

Standard

Numbering System for Taps

1998-10-14

HISTORICAL

J2123_199810

This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1— Caution must be taken when assigning codes to prevent specifying taps that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Taps

2019-10-09

CURRENT

J2123_201910

This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1— Caution must be taken when assigning codes to prevent specifying taps that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Motor Vehicle Seating Systems

2019-10-02

CURRENT

J879B_201910

This SAE Recommended Practice establishes uniform test procedures and certain minimum performance requirements for motor vehicle seats and seat adjusters. It is limited to tests that can be conducted on uniform test fixtures and equipment available in commercial laboratory test facilities. This practice includes a minimum requirement for horizontal forward loads encountered in vehicle forward impacts, and horizontal loads obtained by impacting the vehicle from the rear. The requirements and test procedures in this recommended practice reflect current technology and industry experience. It is intended to subject this recommended practice to a continuing review and revision as technology advances and experience is expanded.