Search Results

The ride comfort of the commercial vehicle is mainly affected by several vibration isolation systems such as the primary suspension system, engine mounting system and the cab mounting system. A rigid-flexible coupling model for the truck was built and analyzed in multi-body environment (ADAMS). The method applying the excitation on the wheels center and the engine mountings in time domain was presented. The variables' effects on the ride performance were studied by design of experiment (DOE). The optimal design was obtained by the co-simulation of the ADAMS/View, iSIGHT and Matlab. It was found that the vertical root mean square (RMS) acceleration and frequency-weighted RMS acceleration on the seat track were reduced about 17% and 11% respectively at different speeds relative to baseline according to ISO 2631-1.

In this paper, a multi-mode active seat suspension with a single actuator is proposed and built. A one-DOF seat suspension system is modelled based on a quarter car model of commercial vehicle with an actuator which is comprised of a DC motor and a gear reducer. Aiming at improving ride comfort and reducing energy consumption, a multi-mode controller is established. According to the seat vertical acceleration and suspension dynamic travel signals, control strategies switch between three modes: active drive mode, energy harvesting mode and plug breaking mode.

To design and optimize the vehicle driveline is necessary to decrease the fuel consumption and improve dynamic performance. This paper describes a methodology to optimize the driveline design including the axle ratio, transmission shift points and transmission shift ratios considering uncertainty. A new and flexible tool for modeling multi-domain systems, Modelica, is used to carry out the modeling and analysis of a vehicle, and the multi-domain model is developed to determine the optimum design in terms of fuel economy, with determinability. Secondly, a robust optimization is carried out to find the optimum design considering uncertainty. The results indicate that the fuel economy and dynamic performance are improved greatly.

This paper describes a simplified model to identify sprung mass using golden section method, the model treats the unsprung mass vertical acceleration as input and the sprung mass vertical acceleration as output, which can avoid the nonlinear influence of trye. Unsprung mass can be also calculated by axle load and the identified sprung mass. This study carries out road test on the vehicle ride comfort and takes a scheme that the group of 20 km/h is used to identify sprung mass and the group of 80 km/h is used to verify the identification result. The similarity of the results from the simulation and experiments performed are, for the sprung mass, 98.59%. A conclusion can be drawn that the simple method to measure the sprung mass in the suspension systems in used vehicles, such as the vehicle shown here, is useful, simple and has sufficient precision.

The road adhesion coefficient has a great impact on the performance of vehicle tires, which in turn affects vehicle safety and stability. A low coefficient of adhesion can significantly reduce the tire's traction limit. Therefore, the measurement of the coefficient is much helpful for automated vehicle control and stability control. Considering that the road adhesion coefficient is an inherent parameter of the road and it cannot be known directly from the information of the on-vehicle sensors. The novelty of this paper is to construct a road adhesion coefficient observer which considers the noise of sensors and measures the unknown state variable by the trained neural network. A Butterworth filter and Adaptive Neural Fuzzy Interference System (ANFIS) are combined to provide the lateral and longitudinal velocity which cannot be measured by regular sensors.

As is known to all, there are some contradictions between the handling and ride performance during the design process of vehicles. Sometimes owing to serious collisions of each criterion in the high-dimensional solution space, the common method to deal with the contradiction is to transform into a single target according to weights of each objective, which may not obtain a desired result. A multi-criteria approach is therefore adopted to optimize both properties and the result of a multi-criteria design is not a unique one but a series of balanced solutions. This paper is focused on the robust design of a simplified vehicle model in terms of not only ride comfort but also handling and stability using a multi-objective evolutionary algorithm (MOEA) method. Using the proposed method, the conflicting performance requirements can be better traded off. One of the most important indexes to characterize the vertical ride comfort is the acceleration of the sprung mass.

To study the torque distribution of track and tire in the wheel-track hybrid drive vehicle driving along the shoreline, an analysis model of wheel-track hybrid drive vehicle was established by using multi-body dynamics (MBD), discrete element (DEM), and shoreline pavement construction methods. The vehicle speed, acceleration, torque, vertical load, sinkage, slip, and other indicators when the vehicle passes the shoal at different wheel speed of rotation are analyzed. The relationships between wheel speed of rotation and slip, sinkage and slip, and vertical load and driving moment were studied, and the laws that the sinkage of tires and tracks is positively related to their slippage and the driving moment of wheels and tracks is positively related to their vertical load were obtained.

The imbalance of propeller shaft is an excitation to the vehicle structure and causes noise and vibration. This paper presents an experimental study of effects of propeller shaft imbalance on vehicle vibration characteristics. A two-piece propeller shaft with unbalance is used in real vehicle test. The vehicle vibration is characterized by accelerations of the cabin floor and of the bearing which supports the propeller shaft. Through the experiment, some interesting phenomena are observed.

In the petroleum and gas industry, cargo truck is one of the most important ways to transfer the skid-mounting from the manufacturer to the job location. Under the condition of bumpy road surface, the random vibration from the ground can easily cause the resonance of the internal equipment components of the skid-mounting, produce large deformation in the pipeline and equipment connection, and even the equipment will be damaged. In this paper, the finite element analysis model and dynamic rigid flexible coupling model of a TEG (Triethyleneglycol) dehydration unit regeneration skid-mounting are established by using the finite element analysis and multi-body dynamics software. The modal analysis of the skid and the vibration of the whole vehicle under different road excitation and driving conditions are carried out. Two solutions are proposed to improve the anti-vibration ability of the skid, and comparative analysis is made.

Vehicle tire performance is an important consideration for vehicle handling, stability, mobility, and ride comfort as well as durability. Significant efforts have been dedicated to tire modeling in the past, but there is still room to improve its accuracy. In this study, a detailed in-plane flexible ring tire model is proposed, where the tire belt is discretized, and each discrete belt segment is considered as a rigid body attached to a number of parallel tread blocks. The mass of each belt segment is accumulated at its geometric center. To test the proposed in-plane tire model, a full-vehicle model is integrated with the tire model for simulation under a special driving scenario: acceleration from rest for a few seconds, then deceleration for a few seconds on a flat-level road, and finally constant velocity on a rough road. The simulation results indicate that the tire model is able to generate tire/road contact patch forces that yield reasonable vehicle dynamic responses.

Vehicle systems often operate with some degree of uncertainty. This study applies the Chebyshev interval method to model vehicle dynamic systems operating in the presence of interval parameters. A full vehicle model is used as the numerical model and the methodology is illustrated on the steering wheel angle pulse input test. In the numerical simulation, suspension stiffness coefficients and suspension damping coefficients are chosen as interval parameters and lateral acceleration and yaw rate are chosen to capture vehicle dynamic characteristics. System responses in time domain are validated against Monte Carlo simulations and against the scanning approach. Results indicate that the Chebyshev interval method is more efficient than Monte Carlo simulations. The results of scanning method are similar to the ones obtained with the Chebyshev interval method.

This paper presents a torque distribution strategy for four-wheel independent drive electric vehicles (4WIDEVs) to achieve both handling stability and energy efficiency. The strategy is based on the dynamic adjustment of two optimization objectives. Firstly, a 2DOF vehicle model is employed to define the stability control objective for Direct Yaw moment Control (DYC). The upper-layer controller, designed using Linear Quadratic Regulator (LQR), is responsible for tracking the target yaw rate and target sideslip angle. Secondly, the lower-layer torque distribution strategy is established by optimizing the tire load rate and motor energy consumption for dynamic adjustment. To regulate the weights of the optimization targets, stability and energy efficiency allocation coefficient is introduced. Simulation results of double lane change and split μ road conditions are used to demonstrate the effectiveness of the proposed DYC controller.