Search Results

Commercial three way catalysts (TWC) are designed to eliminate HC, CO and NOx pollutants emitted from gasoline powered internal combustion engines. TWC have been optimized over many years to meet ever more stringent emission regulations. It has long been speculated that surface electrical conductivity may be a key parameter in controlling catalytic activity, however until now it has not been possible to reliably measure this physical parameter on a catalytic surface. In this study, the surface electrical conductivity of catalyst powders, such as Rh/ CeO1-x-ZrxO2, Rh/ZrO2 and Rh/Al2O3, were measured by EUPS (Extreme Ultraviolet excited Photoelectron Spectroscopy). Then the measured electrical conductivity was compared with catalyst performance from CO-NO and water gas shift reactions which are important for controlling automobile exhaust emissions from gasoline vehicles.

From the viewpoint of the global warming restraint, reduction of exhaust emissions from diesel engine is urgent demand. However, it needs further development in combustion control besides after treatment system. Larger amount of EGR (Exhaust Gas Recirculation) is effective to reduce NOx emission. On the other hand, in-cylinder physical conditions greatly influence on self-ignition and combustion process, especially low O2 fraction charged gas owing to excessive EGR causes misfire. A drastic solution for this problem, fuel injection timing should be optimally manipulated based on predicted ignition delay period before actual injection. For this purpose, Toyota has developed a model based diesel combustion control concept to avoid the misfire and to keep low emission combustion includes in transient condition.

We have developed a novel engine cycle simulation program (UniDES: universal diesel engine simulator) to reproduce the diesel combustion process over a wide range of engine operating parameters, such as the amount of injected fuel, the injection timing, and the EGR ratio. The approach described in this paper employs a zoning model, where the in-cylinder region is divided into up to five zones. We also applied a probability density function (PDF) concept to each zone to consider the effect of spatial non-homogeneities, such as local equivalence ratios and temperature, on the combustion characteristics. We linked this program to the commonly used commercial GT-Power® software (UniDES+GT). As a result, we were able to reproduce transient engine behavior very accurately.

Difference of engine combustion characteristics, species and amount of exhaust gas and PM (particulate matter consisted of SOF and Soot and Ash), and especially PM oxidation characteristics were studied when diesel fuel or bio-fuel, here PME (palm oil methyl ester) as an example, was used as a fuel. The fueling rate was adjusted to obtain the same torque for both fuels and engine was operated under several range of EGR (Exhaust Gas Recirculation) ratio. Under such conditions, PME showed shorter ignition delay time and lower R.H.R (rate of heat release) under 0-40% EGR ratio. With respect to engine exhaust gas species, CO, NO, THC and HCHO, CH3CHO concentration was almost the same when the EGR ratio is higher than 35% (Intake-Air/Fuel: A/F=20). However, PME also showed lower exhaust gas emission when the EGR ratio is higher than 30%.

The introduction of a large amount of EGR gas into cylinders is effective for reducing exhaust emissions in diesel engines. As combustion characteristics under the condition of higher EGR rate are highly influenced by the amount of intake charge gas and its composition. It requires a precise control method for preventing the increase of NOx and particulate matter (PM) in spite of the transient conditions of supercharging and tolerance of turbocharger. In this study, a new control method was developed based on the observed oxygen concentration of charge gas and excess air ratio (stands for the oxygen concentration of burnt gas) which are the main physical factors governing NOx and PM formation. In a conventional method, the intake airflow rate is controlled to meet a target value determined in advance in the stationary engine operating condition.

This paper describes the development of a High Speed Calculation Diesel Combustion Model that predicts combustion-related behaviors of diesel engines from passenger cars. Its output is dependent on the engine's operating parameters and on input from on-board pressure and temperature sensors. The model was found to be capable of predicting the engine's in-cylinder pressure, rate of heat release, and NOx emissions with a high degree of accuracy under a wide range of operating conditions at a reasonable computational cost. The construction of this model represents an important preliminary step towards the development of an integrated Model Based Control system for controlling combustion in diesel engines used in passenger cars.

The efficiency of the NOx Storage and Reduction (NSR) catalysts used in the aftertreatment of diesel engine exhaust gases can potentially be increased by using reactive reductants such as CO and H₂ that are formed during in-cylinder combustion. In this study, a multi-dimensional computational fluid dynamics (CFD) code coupled with complex chemical analysis was used to study combustion with various fuel after-injection patterns. The results obtained will be useful in designing fuel injection strategies for the efficient formation of CO.

An experimental study was conducted to determine combustion and exhaust emissions characteristics in an automotive direct-injection diesel engine dual-fueled with natural gas with the objective of improving exhaust emissions and thermal efficiency. Dual-fuel operation can yield a high thermal efficiency almost comparable to the diesel operation and very low smoke at higher loads. However, NOx cannot be reduced by dual-fueling. On the other hand, at lower loads, a dual-fueled engine inevitably suffers from lower thermal efficiency and higher unburned fuel. To resolve these problems, the effects of exhaust gas recirculation (EGR) were investigated. The results show that in dual-fuel operation, hot EGR can improve thermal efficiency and reduce unburned fuel emission at lower loads, While cooled EGR can considerably reduce NOx at higher loads. A Pt oxidation catalyst can be used for additional reduction in unburned fuel emitted due to dual-fueling.

To facilitate research and development of diesel engines, the universal numerical code for predicting diesel combustion has been favored for the past decade. In this paper, the finite-rate elementary chemical reactions, sometimes called the detailed chemical reactions, are introduced into the KIVA-3V code through the use of the Partially Stirred Reactor (PaSR) model with the KH-RT break-up, modified collision and velocity interpolation models. Outcomes were such that the predicted pressure histories have favorable agreements with the measurements of single and double injection cases in the diesel engine for use in passenger cars. Thus, it is demonstrated that the present model will be a useful tool for predicting ignition and combustion characteristics encountered in the cylinder.

Diesel oxidation catalysts (DOCs) combining the functions of Pd and Pt-Pd alloys have been used in practice to satisfy the strict exhaust emission regulations that have been specified for passenger cars in recent years. Pd is an indispensable component in DOCs because it exhibits superior oxidation activity for CO and HC. To reduce the amount of precious metal used and to improve robustness, it is important to control the electronic state and gas adsorption characteristics of Pd and PdOx during catalytic reactions.In this study, by investigating the CO adsorption behavior of Pd, it was observed that Pd supported on a CeO2/ZrO2 mixed-oxide material (CZ) showed a preferable CO adsorption state and better CO light-off performance. Pd in Pd/CZ became metallic with increasing reaction time, and the CO oxidation performance of Pd/CZ decreased. This change in activity was correlated with CO adsorption on Pd changing from linear-type to bridge-type adsorption.