Search Results

In view of increasing concern over diesel particulates and tightening legislation to control their emission, much work has been done to develop diesel particulate filters (DPFs) and systems to allow them to work reliably. Although a filter will effectively trap solid particles, any material in the vapour phase, such as unburned hydrocarbons, may pass through the filter and subsequently condense. The use of a catalytic wash coat, either on the DPF itself or on a separate substrate, has been proposed to oxidise these hydrocarbons and thus reduce the total material emitted. The use of fuel borne catalysts to aid the regeneration of trapped material within the DPF is also well documented. Such catalyst will also catalyse the oxidation of any hydrocarbons bound up within the particulate. The oxidation of such hydrocarbon occurs at a lower temperature than that of carbon itself, thus allowing lower temperature regeneration of the DPF.

Impending legislation will make it almost inevitable that heavy-duty trucks will have to be fitted with some form of particulate removal after-treatment device. The challenge is to provide a system that is not only environmentally acceptable and cost effective but also durable enough to meet the demands of the trucking industry. Diesel particulate filters (DPF), in conjunction with fuel borne catalysts to facilitate regeneration, are now a recognised technology for meeting future passenger car emissions limits. Retrofitting of such systems to older technology vehicles, where specific environmental concerns exist, has demonstrated the possibility of applying this technology to the heavy-duty vehicle sector. Most of these retrofit applications tend to be to vehicles with a relatively low duty cycle. Whereas this type of duty cycle poses the greatest challenge to the successful regeneration of the filters it is not necessarily the most arduous test of the durability of the system.

A novel dosing system for fuel borne catalyst (FBC), used to assist regeneration with a diesel particulate filter (DPF), has been developed. The system was designed for on-board vehicle use to overcome problems encountered with batch dosing systems. Important design features were simplicity, to minimise system cost, and the use of in-line dosing rather than batch dosing linked to tank refuelling. The paper describes the development of the dosing system which continuously doses FBC into the fuel line feeding the engine injection pump. The theoretical considerations behind the concept are explored, together with the realities imposed by fuelling regimes in which a variable proportion of the fuel flowing through the injection pump is passed back to the fuel tank. Two types of system are considered, ie where 1) FBC is added to the fuel in direct proportion to the flow rate of fuel and 2) FBC is added at a constant time-based rate.

A dosing system has been developed to facilitate the addition of a fuel borne catalyst (FBC) to a vehicle's fuel supply. The on-board dosing system was primarily designed to reduce cost and complexity. One embodiment of the design provided an additional benefit, namely the automatic adjustment of treat rate according to duty cycle. For high duty operating cycles where average exhaust gas temperatures are high, a low treat rate of FBC is supplied. Conversely at low duty where the exhaust temperature is lower, a higher treat of FBC is delivered. Data from field applications are presented to demonstrate this feature.

The influence of swirl on performance and emissions was investigated using a single cylinder Hydra research engine fitted with a high pressure electronic unit injector and a variable swirl mechanism. A large amount of emission data was collected together with the cylinder pressure, fuel line pressure and needle lift signals at a wide range of operating conditions. The influence of a fixed swirl ratio on emissions was also investigated on a Ford HSD425 York engine with conventional injection system and a synopsis of the results is discussed. Laser illuminated high speed cinematography was used to study the interaction of swirl with spray and combustion processes. Data is presented on air- fuel mixing, spray trajectories and flame movement at different operating conditions. Data is also presented to highlight the influence of swirl on the heat release rate, cylinder pressure rise and its relation to measured emission levels, particularly NOx and particulates.

Continuing research into the effect of vehicle emissions is driving legislation, which is increasingly being enacted to encourage the retrofitting of emissions control devices. Of particular concern are emissions of diesel particulate matter and nitrogen oxides. More recently the adverse effects of nitrogen dioxide in particular, have been highlighted. A programme of work is underway in Santiago to demonstrate the suitability of retrofitting diesel particulate filters (DPF) to urban buses. This paper presents data, including regulated and unregulated emissions, from a bus fitted with a DPF that relies on a fuel borne catalyst (FBC) to facilitate regeneration of the DPF.

The most cost-effective way to reduce the level of diesel particulate emissions is to retrofit exhaust aftertreatment devices. While diesel oxidation catalysts will reduce the mass of particles emitted, they will not significantly reduce the number of ultrafine particles, that are considered the most harmful to health. Diesel Particulate Filters (DPFs) are therefore considered the most effective retrofit devices. One obstacle to the widespread adoption of DPFs is that many DPF technologies require low sulphur fuel. Using a Fuel Borne Catalyst (FBC) to facilitate regeneration of the DPF allows a sulphur tolerant DPF system to be produced.

An 8.5 inch bore two stroke engine has been modified into a photographic test rig in which pictures of the complete combustion chamber could be taken vertically upwards through a perspex crowned piston, using a high speed camera. Tests were carried out using several nozzles of the same total hole area. Two fuelling rates and three different air supply pressures were used. At each test condition thirteen cycles of fired data were recorded on 16 mm high speed colour film. At the same time synchronised transient cylinder pressure and fuel injection data were recorded using an on-line data acquisition system. Correlation of jet development from photographs with heat release deduced from the cylinder pressure diagrams using a standard single zone technique show differences due to changes in the hole configuration and in air supply pressure, with approximately constant fuel injection rates.

There is mounting worldwide concern over the health effects of airborne ultra-fine particles. Of greatest concern are the risks due to the cancer-inducing properties of these particles and the aggravation of existing respiratory diseases by the ultra-fine (i.e. <2.5 micron) fraction. This disquiet has already resulted in legislation, regulations and other measures, either mandated or proposed, in the industrialised world to severely restrict particulate emissions from diesel-fuelled automotive transport. Emissions of particles from both new and existing vehicles have been addressed. With the rapid growth anticipated in some developing countries they to will need to address this problem. This paper outlines some alternative solutions to the problem, ranging from alternative power sources, alternative fuels, alternative engine technologies and after-treatment strategies. It also outlines what is required to implement these different solutions.

Fuel-borne catalysts are now an accepted means of aiding the self-regeneration of diesel particulate filters (DPFs). In the past it has been possible to assess the effect of these fuel additives by investigating the temperature at which the filter reaches a pressure drop equilibrium. Under these temperature conditions, the particulate matter is oxidised at the same rate as it is being deposited and there is thus no change in pressure drop across the filter. This technique adequately demonstrates the oxidation temperature of the carbon in the presence of the catalyst. However, it is now well known that such fuel additives also influence the low temperature oxidation of particulate bound hydrocarbons. This phenomenon is not detected by the filter equilibrium technique.

Trapping diesel particulates is effective in reducing both the number and the mass of fine particulate emissions from diesel engines, but unless the accumulated soot can be burned out or regenerated periodically, the vehicle to which the trap is fitted will cease to function after a relatively short time. A programme of work with soot traps using a low treat rate iron-strontium organo-metallic fuel additive to assist and secure regeneration has been carried out. As part of this programme, an advanced specification diesel engine passenger car equipped with a diesel particulate filter (DPF), was operated on roads in the UK for approximately 18 months, during which time the vehicle covered over 50,000 km After completion of 50,000 km on roads, the vehicle was operated on a chassis dynamometer to increase the distance covered with a DPF more rapidly to a final total of 80,000 km.

Recent developments in diesel engines and fuel injection equipment together with the move to ULSD and bio-blends have seen an increase in reports regarding deposits in both injectors and filters. Historically deposits have been generated from a number of sources: bio-contamination, both aerobic and non-aerobic, water contamination, lube oil adulteration, additives, dirt, metals in fuel, and biodiesel degradation. These may be ascribed to “poor housekeeping,” incorrect additivation, deliberate adulteration or some combination. However the recently observed deposits differ from these. The deposits are described and indicate possible precursor molecules that support proposed mechanisms and their ability to form filter deposits.